Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 [5]   Go Down

Author Topic: Metal strap between reedblocks...?  (Read 17503 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Metal strap between reedblocks...?
« Reply #80 on: March 28, 2012, 12:49:00 AM »

This is an amazing trick. I installed a strap between the treble blocks on my Erica and the tuning has suddenly improved! Thanks for the tip.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Metal strap between reedblocks...?
« Reply #81 on: April 10, 2012, 02:41:35 AM »

Yes, it seems to work!
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

saabanders

  • Member
  • *
  • Offline Offline
  • Posts: 19
Re: Metal strap between reedblocks...?
« Reply #82 on: April 17, 2012, 02:24:21 PM »


 Hello.

I have followed this tread whit great interests. And yesterday I tried it on my 4 voice Borsini button accordion. And I was amazed. I sounded noticeably better. Specially when playing accords. Next to try on is an old Hagström. Thanks for this good advice .


Anders     
Logged

bender

  • Member
  • *
  • Offline Offline
  • Posts: 5
    • Pitch Bending for Free Reed Instruments
Re: Metal strap between reedblocks...?
« Reply #83 on: April 17, 2012, 05:10:19 PM »


This is a very interesting thread, and I thank the OP for starting it and for Theo to zoom into a  seducing and fundamental explanation. 

It seems to me there are two cases to consider: 1) when only one reed is speaking and its vibration causes an oscillatory movement in its own reed plate, because the block on which it is placed is induced to vibrate, and 2) when the reed plate of a first speaking reed is being vibrated by a resonance between the block and a second speaking reed. 

In case (1), the frequency of the induced motion in the reed plate is likely to be the same as the fundamental of the musical tone, with probably a phase difference.  It's difficult to know for sure how this affects the sound of the reed, but my guess is that it can cause a lowered volume and a frequency spectrum with reduced overtones, perhaps causing a "less bright" sound.  Some listeners might prefer such a timbre. 

In Case (2), the situation is more complex.  If the reed plate is vibrating at a frequency that is an integer multiple of the fundamental of the speaking reed, the effect on sound might be similar to that of Case (1).  When the frequencies are different, aperiodic pressure pulses will contribute to the sound produced, simply because such pulses contribute to the chopping of the air produced by the relative motion between the vibrating tongue and the vibrating reed plate.  In other words, there will be some measure of noise, and it's magnitude can, in general, range from imperceptible, to the annoying "warbling" described by others. 

The video showing synchronization of the metronomes is very interesting, though note that these metronomes are tuned to have very nearly the same individual frequencies.  Thus, their oscillations are pulled in phase, with all having vibration amplitudes close to their individual responses.  When two linear oscillators of different frequencies are coupled, their oscillations can be in unison, at some intermediate frequency, albeit with possibly a greatly reduced amplitude.  If the separate natural frequencies are far apart, I believe complicated, seemingly chaotic, motion is possible.  Thus, I can see that, in some cases, very unpleasant warbling can occur when more than one reed is vibrating in a reed block that is susceptible to it's own harmonic behavior. 

Those familiar with the Asian free reed instruments can observe that the natural vibrational frequencies of the reed tongue and the coupled tube resonator often differ, and the resulting musical tone of the coupled vibration operates at a pitch somewhat intermediate between the two.  This sound, however, is entirely enjoyable, though I'm not suggesting that all the important physical mechanisms are the same. 

Contrary to some here, I don't see that the effect of reed block motion occurs via influence on the reed tongue vibration itself.  I see it happening through its effect on the air chopping that is so fundamental to free reed operation.  For instance, since the tongues are mounted tip up, their attachment to the plate/block is near the bottom of the block, where the block's motion is likely at some minimum.  In my view, I see the tongue vibrating pretty much like it wants to vibrate, with the block doing the same, and their nexus is at the top, where their relative motion is most pronounced.  This is where the musical tone is affected. 

For those energetic enough, the entire phenomenon should be relatively easy to set up for experimentation, in an apparatus that allows vibration of the reed plate at user-selected frequency and amplitude. 

Best regards,
Tom
Pages: 1 2 3 4 [5]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal