Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: A Hohner to Refurb and Learn From  (Read 9360 times)

0 Members and 1 Guest are viewing this topic.

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: A Hohner to Refurb and Learn From
« Reply #40 on: May 07, 2012, 06:31:38 PM »

Instead of cutters to remove bellows pins I simply use a small nail puller; lever action gives a lot more control and force than a cutter, especially when the pins are stuck. I put a thin piece of hardwood on the case as a pivot and lift the pin; I can increase the thickness of the pivot piece if I need to.
« Last Edit: May 07, 2012, 09:01:14 PM by Québécois »
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

chappie86

  • Folker
  • Good talker
  • **
  • Offline Offline
  • Posts: 65
  • Discovering Melodeons
Re: A Hohner to Refurb and Learn From
« Reply #41 on: May 07, 2012, 08:06:21 PM »

I have gained access to the guts of the box now.

The reed plates are stamped H and M. All of the reed valves are thick blue leather, most are still in place but there were three that are loose in the box so I am guessing some of the internal valves are missing. Should I replace these with newer plastic valves? If so, which ones shall I go for? and are there any good threads detailing the process of re-valving?



Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: A Hohner to Refurb and Learn From
« Reply #42 on: May 07, 2012, 08:44:29 PM »

I have gained access to the guts of the box now.

The reed plates are stamped H and M. All of the reed valves are thick blue leather, most are still in place but there were three that are loose in the box so I am guessing some of the internal valves are missing. Should I replace these with newer plastic valves? If so, which ones shall I go for? and are there any good threads detailing the process of re-valving?

Others may disagree but judging from the age of this box I would recommend relaxing the reeds as the wax is almost certainly dried out. If it is dried out the reeds will not be held solidly to the block and be impossible to tune. This will also give you he chance to inspect the valves on the inside of the reeds.

I would replace all the valves and my personal preference s to use vinyl valves from Charlie Marshall.

As to how to, remove the old valves and scrape any adhesive remaining on the reed plate, I use the back of a scapel blade, then I use EvoStik to stick the new valves in place. Use the glue sparingly on the rivet end of the valve.

The valves I use come in 3 varieties depending on the required length, also the longer reeds have either 3 or 2 leaves to increase the springiness. The valves will need trimming to length after they are fitted and I alway trim the leaves back proportionally to the overall shortening of the valve.
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal