Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Peter Stormy Hyde on May 05, 2013, 10:35:41 AM

Title: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 05, 2013, 10:35:41 AM
Following the discussion with “nudiefish” about a custom made melodeon on the site, I thought it might be a good idea to show the steps involved in making the “Posh Box” from order to inception. There will be a few photos, and any replies within my text from “nudiefish” will be in blue text.
As I’m now in semi retirement!!!! There are no more 60-hour weeks.

Original Order;
Key D/G  21 button 3 voice (TTT) French Musset, 3 stops. 12 Bass 2 stops.
Size 240mmx150mm.
Timber; Frames “Birds Eye Rock Maple” End Plates and treble mechanism; Masur Birch, none in my stock or in Adelaide, replaced with Quilted Sycamore (cut before 1913.) Contrast; “Jarrah”   
Keyboard; Raised with 15 mm buttons. Bass side; 15mm buttons
Strap system; Double.
Fitted with on board Mike System.

Daily log;
Day 1
Make up blank frame with “Jarrah” side rails
4 hours
Day 2
Frame blanks are ready for ripping down.
End plates and bulkheads glued up and finished.  End plates made from “Queensland Red Cedar” core with two veneers on either side, two “blue” blind veneers athwartships, and the outside 2 fore and aft, Bulkheads made from gluing together two 1.5 mm sheets of aeroplane ply, external grain running athwart-ships.
7 hours
Photo 1 shows blank frames before rip down.
Day 3
Removed end plates from under press, they had been there far too long (I hade the day off between clamping and removal) so mildew on hidden veneers, one bubble where it had not stuck down so used the iron too fix down, this works well on PVA glues.

I call the veneers inside the box “hidden” and the ones between other veneers or timber as “blind”.

Rip cut the blank frames using very fine blade (blank was only 11.5 mm thick and I needed 5mm for each frame, and the blade had 1mm kurf) but went very slowly and it worked very well, not much sanding needed and frames were finished in the thickness sander to 5mm.

One side of frames were coated with red oil, made from the gum of the Yakka tree native here in Australia, this highlights the reeds within the timber but does not stain, this allows choice after spraying as to what side the customer wants on the outside.

Treble mechanism was glued up ready for spraying.
Bass button riser cut and blind drilled.
5 hours.
Photo 2 shows frames after rip down and sanded with Red Oil sent too “nudiefish”.
Thank you very much for sending me that shot.  I simply love the frames. I've blown up the image so as to better take in the pretty maple lines and all that swirly detail.  Plus the rich red borders are lovely.  I'm going to enjoy the look of this box just as much as the sound of it. 
Secondly, I love the idea of you documenting the making of the box.  Actually, having a pictorial record of it being made is quite a special gift. I don't think that there would be very many people in the world who could produce images of their squeeze box being born, and in living colour too.  And posting the results to the melodeon site is also an excellent idea and one worth pursuing.  These guys live and breath melodeons and I agree there are many who would be thrilled by the notion of seeing a melodeon grow out of nothing.  I know that I would!
Anyway, thanks Stormy, please go ahead, and look forward to watching my box come to life.   
Cheers,


Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on May 05, 2013, 11:29:36 AM
Thanks Stormy, looking forward to seeing the box develop.  I'm actually leaving for Europe in a few days so I will have to catch these installments on those rare occasions when I stumble upon free WIFI. 
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Owen Woods on May 06, 2013, 10:22:49 PM
Very nice!

I've heard rumours about exotic woods being difficult to import, even when they are part of an instrument and from a stock like yours, rather than being illegally logged. Have you had any troubles with that?
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Chris Ryall on May 06, 2013, 10:41:53 PM
The desk under my computer is made of an old recovered kitchen, itself a recycled 1950s school  chemistry lab - "ironwood" I'm told.

But you can only plumb in square sinks  ;)
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 07, 2013, 01:09:36 AM
Very nice!

I've heard rumours about exotic woods being difficult to import, even when they are part of an instrument and from a stock like yours, rather than being illegally logged. Have you had any troubles with that?
Thank you.
Yes; there is now a problem along those lines you mention, even if it is recycled timber, but it is a little strange as some of the very threatened Australian species are not on that list. I have a big stack of off cuts of Brazilian rosewood that came from a guitar maker some years ago, so i would not use that on an export instrument.
I think I'm safe with the timbers on this box.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 07, 2013, 01:15:57 AM
The desk under my computer is made of an old recovered kitchen, itself a recycled 1950s school  chemistry lab - "ironwood" I'm told.

But you can only plumb in square sinks  ;)
I once had a customer send me the timber from a toilet door from an old derelict farm where he was born up in Northern NSW, the timber in that door was Queensland Rosewood, Queensland Ceder and Blackwood, obviously the customers grandfather who built the farm house had good taste.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 13, 2013, 08:15:00 AM
Day 4
Sand down and spray all parts, this is done so that I get a good finish on the inside, and the outside is protected from scratches and glue.
8 hours

Question nudiefish; would you like the darker leaver stock as seen in front of the mechanism or would you like the sycamore again, my feeling is the darker would look good.

Thanks for providing an update on my box, Peter.  I actually look foreword to watching our project develop and grow and I love the look of the thing.  It is indeed beautiful, and I agree, please keep the dark wood as you have it.  Having a blond box allows a very sweet red colour to set it all off.
I must admit, Stormy, that ever since playing your other box and hearing that resonant deep bassoon sound it has me thinking.   Either way I can't wait to get my hands on your creation.

Day 5
Cut trenches on inside of frames and then cut down to size, and fit corners. Fix risers to leaver stock. Start cutting slots for treble leavers in Treble Mechanism Block.
4 hours
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on May 13, 2013, 08:20:32 AM
This is going to be one beautiful Box Stormy - thanks for the updates !
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 13, 2013, 10:49:01 AM
This is going to be one beautiful Box Stormy - thanks for the updates !
Thank you Adam-T

Day 6
Finish slots in treble mechanism, and glue on capping. Fit bulkheads to frames, and then router out the holes. Make reed block shoes. Extra reed block shoe was made for the treble 3rd voice  reed block, as I will also be making a bassoon reed block, so it can be swapped for the 3rd voice tenor.

You will notice that I use an overhead router (in fact it is a heavy duty grinder) to router out the holes, the stand and the grinder have served me well as they are over 30 years old.

The radial arm saw is used only for cutting the slots on the mechanism, and nothing else. I have had a couple of blades made with V tips so the spring goes center in the slot.
I set the saw up again for the photo so I would not normally use it with the block sander behind the fence, and of course the capping was put on after the slots were cut.

And the real stupid thing here is I have just made a 23 key mechanism for a 21 key instrument, it is possible to cut a bit off the ends and slide it into the slot without being seen, but this time I will make a new one. Automatic mode can be deadly at times.
4 hours
 
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 26, 2013, 11:33:05 AM
Day 7
Back "on deck" after getting called on to another job.

The first photo shows the bulkheads fitted to the frames, at this stage they are held together with rubber bands. I always make the bulkheads  slightly oversize then i cut away what is needed at the back and bottom edges.

The second photo shows the slides fitted to the bulkheads using cardboard as spacing material*
*Now before you all throw your hands up in the air that cardboard is used by the British Museum for numerous tasks and one of them is the stiffener within leather bound books, it is acid free and the edge that is cut by a guillotine is as hard as any timber . This cardboard was purchased by me 35 years ago to make concertina bellows, and it worked very well for that job, I bought a pallet load of the stuff. It has been stored in the roof of the garage for all that time and is still as good as the day i purchased it, so it is very stable. If anybody is looking for this cardboard I would suggest that you get in touch with your local book bindery, then that might now be in China, but I'm sure the bindery at the British museum will be helpful.

I glue the cardboard over the holes and then quickly cut out the holes using a fret saw, i could put them back under the router, but the saw does a cleaner cut, do not use blades from the hardware store go to a jewellery suppler and get good quality fine blades.

 
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on May 27, 2013, 07:59:46 PM
Coming on Nicely Stormy - keep the shots coming !!
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on May 28, 2013, 12:33:53 AM

Coming on Nicely Stormy - keep the shots coming !!
Thanks for the encouragement.
Day 8
Fit reed block shoes on bass side
Glue up treble reed block blanks. With this I work with a height of 300mm, as this is what will go under my book press. I start by cutting the dividers needed I always make it a 12 cavity reed block, and as my treble buttons are spaced at 18mm I then have a 14mm cavity with a 4 mm divider.  So with this in mind I have laid out strips of 14mm craft board glued down to a bed of ply with slots left in between for the dividers. I now insert the strips into the space for them then I glue down a sheet of dividing bulkhead that is 5mm thick  (there is good reason that it is so thick as I’m always working at getting a 3 voice box into an instrument 150mm wide,) I then place this under the book press for a few hours, then I repeat the process on the other side. I now have what I call my “reed block blank” ready to slice off any size I require.
Yes I know it does not look like timber, it is not; it is in fact foam that is used in boat, shipping, and aerospace industries, so it is of a very high quality specification and has no acoustic quality’s at all, it is dead as a Dodo and that is what is needed so that it does not interfere or scavenge from the resonator.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on May 28, 2013, 07:30:36 AM
Excellent stuff - great to see the foam reedblocks in parts - it`ll be very interesting to see them when they`re complete and also with reeds waxed in .
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on May 28, 2013, 08:55:56 PM
The bloke hopping impatiently from one leg t'other waiting for this darned box is me,  Peter!  Thanks for all the updates, Mate. I know that you are talking a lot of trouble in documenting the process.  I'm more than a bit curious on how it all comes together.  For instance,  so that's how the slides work??
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 03, 2013, 11:59:41 AM
The bloke hopping impatiently from one leg t'other waiting for this darned box is me,  Peter!  Thanks for all the updates, Mate. I know that you are talking a lot of trouble in documenting the process.  I'm more than a bit curious on how it all comes together.  For instance,  so that's how the slides work??
I hope it is not because you want the dunny; they are a little hard to find in Europe
Day 9
Now I will explain why I need wide dividers within the reed blocks. As I never make any instrument any wider than 150mm and this includes three rowers and 3 voice two rowers I’m pushing for all the free space I can get, as I do not want the back reed blocks right under the treble mechanism for obvious reasons. If I put a thick divider in the reed block and then put slots in so the reeds can pass each other but still stay within its own cavity, by doing this I can reduce the top width of the reed block by 5mm. This then gives plenty of room between reed blocks for the reeds and valves not to interfere with each other. The slots are cut out with the bench-mounted router, and I should have taken the slots a little deeper as I can take the divider down to 0.5mm with no problem at all.


Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 10, 2013, 12:02:48 PM
When I glue down the capping on the reed block the shoe goes up against a very ridged surface like as a small table clamped into the vise and under that I place a wedge with the same taper as the reed block that way I get a good surface for the clamps, or the wedge can go on the top of the capping as shown. I use a 1.5 mm reed block shoe; if it is any thicker it starts to flatten the reeds. When fitting reeds to the reed block and they are too short for the cavity then fill the cavity from the top and reduce the cavity size, some makers and repairers use a strip of timber at the bottom of the reed to rise it up the cavity, it works but flattens the reed in the process.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on June 10, 2013, 01:12:51 PM
Thanks for sharing all this, Stormy !!! . keep 'em coming, it`s great to have this here as a resource, you`re the only one i know of who makes Foam reedblocks , I think even Strasser used Wooden ones (albeit Balsa if I remember rightly) in their foam laminate cased Steirische
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 11, 2013, 12:02:48 PM
Thanks for sharing all this, Stormy !!! . keep 'em coming, it`s great to have this here as a resource, you`re the only one i know of who makes Foam reedblocks , I think even Strasser used Wooden ones (albeit Balsa if I remember rightly) in their foam laminate cased Steirische
I’m glad you are getting some use from it.
Intresting about the Strasser that they are now using balsa and foam it is the first I have heard of any other makers using these material. When I started using balsa and foam I copped a fair amount of stick as most people thought I was nuts, just as well there are a few nuts in this world.
Here is a link to an old site where I wrote a little about my work at the time on balsa reed blocks, reading it again after so many years I would have to make a couple of changes!!!

http://www.19larchclose.freeserve.co.uk/acc/Stormy.htm
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on June 11, 2013, 12:40:49 PM
Intresting about the Strasser that they are now using balsa and foam it is the first I have heard of any other makers using these material.


They aren`t now but they did experiment with them and other unorthadox materials a few years back
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on June 12, 2013, 11:13:36 AM
Very nice and interesting report!
Thank you very much for sharing all this interesting information.

Whre are the pictures about ths building process?

---------------------------------------------------------------------------------------------
I did build an other big box this Year.
It is a GCFB Heliconbox all in massive wood. 19,8cm x 36cm 5,2 kg

https://plus.google.com/photos/116672106411032803534/albums/5874487803623754961?banner=pwa

Best regards, Johann Pascher
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on June 12, 2013, 11:40:46 AM
Beautiful Job Johann !!
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 17, 2013, 01:19:21 AM
Intresting about the Strasser that they are now using balsa and foam it is the first I have heard of any other makers using these material.


They aren`t now but they did experiment with them and other unorthadox materials a few years back

I did forget to mention that Bryan Lafleur in Texas had tried the balsa, and the feed back I had from him was very positive, but my mind had been on the bigger European makers.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 17, 2013, 01:35:29 AM
Very nice and interesting report!
Thank you very much for sharing all this interesting information.

Whre are the pictures about ths building process?

---------------------------------------------------------------------------------------------
I did build an other big box this Year.
It is a GCFB Heliconbox all in massive wood. 19,8cm x 36cm 5,2 kg

https://plus.google.com/photos/116672106411032803534/albums/5874487803623754961?banner=pwa

Best regards, Johann Pascher
G;day John fantastic work, I'm impressed with the whole instrument, I find the way you have resolved the treble levers of interest, is there much "bounce" in them or is that resolved?.

Are you seeing any photos at all?  The post has drifted off a little so there has been no new photos with the last couple of posts, but I will remedy that a little later today.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 17, 2013, 01:59:40 AM
The “Bass Button Riser” has been blind drilled and then screwed down to the front surface of the accordion frame, I then drill all the way through with a small drill I can then counter sink with the 10mm drill at the back, so when drilling from the front with the 10mm drill I get a good clean exit. There is very good reasons for screwing it down rather than gluing it in place as I will want to be able to remove it later on for various reasons.

I think my titles of photos are getting a little out of sync’, this is just for filing within my file system, but all is self-explanatory.

Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on June 20, 2013, 07:30:10 PM
G;day John fantastic work, I'm impressed with the whole instrument, I find the way you have resolved the treble levers of interest, is there much "bounce" in them or is that resolved?.

Are you seeing any photos at all?  The post has drifted off a little so there has been no new photos with the last couple of posts, but I will remedy that a little later today.
This is acually off topic here, and i bette would talk about the things you explain.

The problem with the pictures seams to be solved, id did not change anything and the pictures do show up now.

To the questions:
 is there much "bounce" in them or is that resolved?
No there is not a lot of bounce, sure it is always a compromise. In may case i could  even reduced the bounce if i would not use wood for some parts of the levers. Dimension on the wooden parts is very low in this case.
The treble keyboard is basically conservative and in the traditional way.
The leavers are made up of a wooden and a Aluminum part glued together near where the bearing is placed.
I use plastic bearings within the wooden part. The rods are 1,5mm in diameter. Springs differ on all for rows. Springs are turned by hand with a self made tool. Also important is that the flaps are very light weight.  Fitting the bearings and putting all in a right angle is difficult. All must move easily without having to much play on the other hand. I did make different treble keyboards in the past as well, and all do have pro and contras.


Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 23, 2013, 11:47:13 AM
G;day John fantastic work, I'm impressed with the whole instrument, I find the way you have resolved the treble levers of interest, is there much "bounce" in them or is that resolved?.

Are you seeing any photos at all?  The post has drifted off a little so there has been no new photos with the last couple of posts, but I will remedy that a little later today.
This is acually off topic here, and i bette would talk about the things you explain.

The problem with the pictures seams to be solved, id did not change anything and the pictures do show up now.

To the questions:
 is there much "bounce" in them or is that resolved?
No there is not a lot of bounce, sure it is always a compromise. In may case i could  even reduced the bounce if i would not use wood for some parts of the levers. Dimension on the wooden parts is very low in this case.
The treble keyboard is basically conservative and in the traditional way.
The leavers are made up of a wooden and a Aluminum part glued together near where the bearing is placed.
I use plastic bearings within the wooden part. The rods are 1,5mm in diameter. Springs differ on all for rows. Springs are turned by hand with a self made tool. Also important is that the flaps are very light weight.  Fitting the bearings and putting all in a right angle is difficult. All must move easily without having to much play on the other hand. I did make different treble keyboards in the past as well, and all do have pro and contras.
I did have a little "bounce" on my 3 rowers, I was using 2 mm rods (bike spokes at the time) and I tried a couple of things to stop it, although I did have one customer say if i could get the same bounce over 3 rows it would have a terrific vibrato effect.
I resolved the problem by reducing the weight on the pallets by using balsa wood that is half the weight of other timbers, and then the real saving was foam as it is only one 3rd the weight of the balsa,  it makes fantastic pallets, this then has other benefits, like using thinner felts and leathers, and it also makes the box faster, as there is less dragging effect caused by the mass weight of the pallets themselves.

I likewise has tried various ways of making treble mechanisms, the main reason I have stayed with the method that I now use is that the mechanism is not so high, and I still get the lift on the pallets I need, and i only have 2.5 mm travel in the button, and another thing is I can still get my 3 row instruments into the 2 row backpacks.   
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 23, 2013, 11:53:53 AM
Fitting pallets to bass mechanism, in photos you will notice that I have used leather boot lacing. The lacing is placed into the slot and the leaver pushed down into it, as the leather is 1mm thick it allows the pallet to self align with the bulkhead as the leaver is not interfering anywhere else along the slot. if I’m using round rod for the mechanism then I use rubber spline that I have had made for the job. Here you will notice that I have used bolts on the leavers, so here I have used the same leather and of course a dob of glue will be placed over the top later on.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on June 23, 2013, 12:12:22 PM
Thanks Stormy - I like the leather idea as it looks like it makes for easier repairs later on - if the lever rusts it won`t split or ruin the wood as there`s plenty of width .
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 23, 2013, 12:40:37 PM
Thanks Stormy - I like the leather idea as it looks like it makes for easier repairs later on - if the lever rusts it won`t split or ruin the wood as there`s plenty of width .
Thanks Adam-T
I'm glad you like it, the leather lacing is very handy in the workshop as it comes in a couple of thicknesses and widths, and is always very uniform. The lacing gives a pivot point that works the same way as the rubber grommet type pallets. These leavers will not rust as they are brass, but you do have a good point, and the pallets are balsa, on the treble side I will be using foam pallets.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on June 23, 2013, 08:02:56 PM
Fitting pallets to bass mechanism, in photos you will notice that I have used leather boot lacing. The lacing is placed into the slot and the leaver pushed down into it, as the leather is 1mm thick it allows the pallet to self align with the bulkhead as the leaver is not interfering anywhere else along the slot. if I'm using round rod for the mechanism then I use rubber spline that I have had made for the job. Here you will notice that I have used bolts on the leavers, so here I have used the same leather and of course a dob of glue will be placed over the top later on.

Hi Peter, i also like your solutions. I agree that the main thing is to reduce the weight of the pallet, so the assembly lever plus pallet does not get into a critical resonance less weight is preferable in every way. I also did use balsa pallets on one box.
On a other box i used 0,4mm glass fiber with a lether and a top u profile that gets in the same direction as your leather solution, so the pallet is also to some extent selves adjusting. I tried a few other more complex leaver pallet Assembly's.

I never could get hold of foam that is of the quality as you use it. So my be at one stage i my be using foam in the future as you. Did you ever put a complete treble pallet used on a two reed-ed box on a scale?

I also like your bass mechanic, do yo get this Assembly's from Italy?

Best regards, Johann
 
 
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on June 24, 2013, 10:27:28 AM
Fitting pallets to bass mechanism, in photos you will notice that I have used leather boot lacing. The lacing is placed into the slot and the leaver pushed down into it, as the leather is 1mm thick it allows the pallet to self align with the bulkhead as the leaver is not interfering anywhere else along the slot. if I'm using round rod for the mechanism then I use rubber spline that I have had made for the job. Here you will notice that I have used bolts on the leavers, so here I have used the same leather and of course a dob of glue will be placed over the top later on.

Hi Peter, i also like your solutions. I agree that the main thing is to reduce the weight of the pallet, so the assembly lever plus pallet does not get into a critical resonance less weight is preferable in every way. I also did use balsa pallets on one box.
On a other box i used 0,4mm glass fiber with a lether and a top u profile that gets in the same direction as your leather solution, so the pallet is also to some extent selves adjusting. I tried a few other more complex leaver pallet Assembly's.

I never could get hold of foam that is of the quality as you use it. So my be at one stage i my be using foam in the future as you. Did you ever put a complete treble pallet used on a two reed-ed box on a scale?

I also like your bass mechanic, do yo get this Assembly's from Italy?

Best regards, Johann
 
G'day Johann
The foam is used in the boat building industry and is what is used to laminate fiberglass and foam to give it strength and lightness.
I have weighed the pallets in the past, but my scales are not as good as they used to be so I cannot give you a truthful answer on that one.

What you are looking at is the very last 12 bass mechanism (I still have 8 bass ones) that I got from East Germany just as the wall fell, I think i got all that was in the warehouse at the time, and they are spring retention leavers and they are brilliant, very good German engineering, they have never given me a single moment of grief. I much prefer them to the Italian method as they came with springs as well, and they cost me at the time $0.50 cents each unit. I did take one unit to Carini in Italy to see if they could get them made, although Roberto was very impressed with them he was not keen to do anything about getting them made. Of course if one needed plenty of them and as they could be done in a sheet metal workshop I'm sure the Chinese would be able to make them cheaply and still keep the quality.

Interestingly; I used to get all my parts from East Germany  in the early days, and the reeds prey wall or should I rightly say "unification" were very good but after they were not so good and the quality dropped off. I still have early accordions out there that I made 27 years ago with E/G reeds and bellows still going strong, and i have never had a reed breakage from them. I had one customer whose instrument got a little damaged so I used as much of the original timber and turned it from a full sized box into a flutina and used a single voice E/G set from the original 2 voice and it sounded fantastic.

Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 01, 2013, 12:38:45 PM
On the bass side I have used balsa pallets this is because I had the stock ready, and on the treble side I made them from foam.
There are many ways of making pallets but I chose to have a very special router cutter made that is fully adjustable so any pallet from the smallest to the biggest can be made on that same cutter, it allows me to shape the edges be that ¼ round or straight 45 degree angle and the slots any way I need.

 These pallets are made in just one pass then I run the stock through the band-saw to cut off the pallet strip. The strip is then cut into the desired pallet length then the pallets are placed into an angle jig and passed under the thickness sander to profile the front and back edges.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 01, 2013, 12:43:07 PM
Here are the foam pallets
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on July 01, 2013, 01:03:26 PM
Thanks again - How do you find the foam withstands facing replacement ? , I`d think the Balsa ones would have to be replaced if they need facing but is foam more resilient ? .... also what is the benefit of using balsa and foam pallets , I`d have thought this is one area where the traditional servicable rigid wood which is still very light (or solid resin / Fibreglass as in the better steirisches & Classical CBAs, heavier though) would have been better .

Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 02, 2013, 11:51:33 PM
Thanks again - How do you find the foam withstands facing replacement ? , I`d think the Balsa ones would have to be replaced if they need facing but is foam more resilient ? .... also what is the benefit of using balsa and foam pallets , I`d have thought this is one area where the traditional servicable rigid wood which is still very light (or solid resin / Fibreglass as in the better steirisches & Classical CBAs, heavier though) would have been better .
Both the balsa and foam handle re facing very well, I use PVA glue that is water soluble, i can just place the pallets down on a wet cloth and after about 10 minutes the whole lot just falls off. But even so balsa and foam are stronger most would think, so you can just pull the felts off.

The big benefit by using balsa and foam is the speed of the instrument is improved because of the reduced weight. The other point is that I'm not limited to off the shelf sizes and designs.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on July 07, 2013, 05:02:19 PM
I`ve not seen Water soluable PVA (not one for glueing the casings together on boxes likely to be used for the Morris in the UK - LOL) sounds like a good move for pallet facings though ..
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 09, 2013, 03:06:07 PM
I`ve not seen Water soluable PVA (not one for glueing the casings together on boxes likely to be used for the Morris in the UK - LOL) sounds like a good move for pallet facings though ..

One could always use Rabbit Skin glue that you can get from Art Suppliers, as it is still used to size canvases.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 09, 2013, 03:09:32 PM
The cutting out of the reed block seals can be a tedious job at times, there are different ways of doing this job but over the years of trying most I have found this way the best.
I staple a sheet of the double felted leather (skiver) down on a kitchen chopping board; I then staple the template over the top and then use double beveled chisels to cut them out. I know everybody’s first thoughts would be to use a very sharp art knife or scalpel, but no mater how sharp they are they will draw the leather.
Some of the other ways is to use jute or hemp string or even bellows seal sponge.
Here is some discussion I have had before about this subject.

http://forum.melodeon.net/index.php/topic,7527.msg93681.html#msg93681
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on July 09, 2013, 05:03:32 PM
The cutting out of the reed block seals can be a tedious job at times, there are different ways of doing this job but over the years of trying most I have found this way the best.


I`ve only done it once , to a Hohner using Charlie Marshall's self adhesive reedblock gasket material - I stuck it to the fondo and carefully cut out the circles using a scalpel (with the action removed of course ;-) , fiddly but did the job nicely . I guess a Template helps , with circular holes like in Hohner a sharpened pipe of the right diameter and a hammer would make the perfect punch (thanks for the tip Graham) after laying the material on wood ..  I hadn`t a hohner template so used the scalpel after sticking the stuff down way
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on July 12, 2013, 04:27:21 AM
Last night Stormy sent me a little email update on how the box was going.  Essentially, its getting very close to finishing. 

In the telling, though, he revealed just how clueless I really am in the craft of making melodeons.  He said that he just finished the "air leak" test where he fills the box with water to see where the water seeps out.  I totally believed him and wondered just how he protected the working mechanisms.

I re-read that paragraph several times trying to work out how he did the trick.

It is sad to say, that it took me about 30 seconds to realise that he was pulling my leg.  Actually, I never did work it out, in the next paragraph he told me he was kidding. 

Filling the box up with water.....  Jeeze....
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Nick Collis Bird on July 12, 2013, 07:33:55 AM
The desk under my computer is made of an old recovered kitchen, itself a recycled 1950s school  chemistry lab - "ironwood" I'm told.

But you can only plumb in square sinks  ;)

A really good source  of Mahogany  and Walnut can be found very cheaply in old Victorian wardrobes.
 I broke one up recently and was astounded to find solid wood and not veneer.  ;D
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Steve_freereeder on July 12, 2013, 08:41:49 AM
The cutting out of the reed block seals can be a tedious job at times, there are different ways of doing this job but over the years of trying most I have found this way the best.


I`ve only done it once , to a Hohner using Charlie Marshall's self adhesive reedblock gasket material - I stuck it to the fondo and carefully cut out the circles using a scalpel (with the action removed of course ;-) , fiddly but did the job nicely . I guess a Template helps , with circular holes like in Hohner a sharpened pipe of the right diameter and a hammer would make the perfect punch (thanks for the tip Graham) after laying the material on wood ..  I hadn`t a hohner template so used the scalpel after sticking the stuff down way
I use hollow leather punch* tools for jobs like this. Ideal!

*Do a google search, or see here (http://www.amazon.co.uk/Am-Tech-Hollow-Punch-Set-Pieces/dp/B004LAP3M0/ref=sr_1_1?ie=UTF8&qid=1373614606&sr=8-1&keywords=hollow+leather+punch+set) (warning - link may not always be available).
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on July 13, 2013, 07:32:53 PM
I have made my own oval and triangle punch tools for leather used for pallets. You my have a look at my workbench in attached picture.
I glue the leather fist to the felt before punching. For square Pallets i use a knife.
@ Peter Stormy, thank you for reply all you information on the subject.

Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Prestidigitator on July 13, 2013, 08:04:13 PM
The gasket stuff for the reed block bases, as supplied by Charlie Marshall, is called OLOVISC.

I shape it by cutting the piece to fit the reed block base; then I use a small jewellers hammer with a copper and nylon interchangeable head, to lightly "dress" the gasket against the block. This gives an imprint of the hole locations.

I then, like Steve, use a suitably sized "wad punch" (part of an old Eclipse set I've had 40 years or more), to punch the holes.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 16, 2013, 10:55:24 AM
It is now time to start assembling and gluing up the frames, at one time I used to clamp the whole thing together, but it was very hard to get all the corners at 90 °. I have made up a jig that is able to take one side and one end at the same time and then I clamp them together using a picture frame clamp, I have a corner protector on the top corner as the strap can collapse the corner as it will exhort a lot of pressure. Once you have a pair of these then clamp them together, depending on how good your jig is you will then get all the corners at 90 °.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Owen Woods on July 16, 2013, 11:30:59 AM
That is a beautiful grain. Can't wait to see it finished.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on July 16, 2013, 12:00:27 PM
Looks Fabulous Stormy - thanks for sharing this series with us, it`ll be something for you to look back on in many years also (as we all know, Melnet is timeless and will be here fovever  :||: :|||:)

On a side note - I have to be honest . I prefer the look of the bass end without the contrast colour button riser , that grain as Owen said is Beautiful, It`d be a shame to cover ANY of it up
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 17, 2013, 12:21:50 AM
Thanks Mates for the feed back.
Many years ago I was at the National Folk Festival in Canberra and as I was walking into the bar area pree session time and two blokes were walking out, and one said to the other "what brand of accordions were they", the other person said " a well known Italian brand", when i got into the bar there were only 3 of my customers within playing my accordions together.

From that point I made very sure that mistake is not made again,  I use 3 timbers the main timber, on the frames, then a highlighting timber on the end plates and treble mechanism then a contrasting timber to box it in. 
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 21, 2013, 05:04:31 AM
Cutting out end plates can either be hard or very easy, the main thing is to have all the right tools in place before you start, that is; V support, good fret saw, or piercing saw as some call it, very good blades of various TPI, compressed air, and candle wax.

As I have already given the end plates a coat of the lacquer I need a glue that will stick the template down and good enough to hold it down during the whole cutting process, for this I use good quality stick glue. I then go through and drill small holes into the waste, then I just sit there and take my time, and with a little bit of patience it dos not take to long to master the use of the saw, each treble end plate takes me about 45 minutes to cut out. I have a small jet of air that is directed to blow away the sawdust so I can see the lines. The template can be washed off with a damp cloth without lifting the veneers, but far more care has to be taken if there is no finish on the veneers as they will very quickly lift off with the moisture, it is surprising how fast this can happen.

To me the good quality fret saw is the most useful hand saw in the workshop as so much work can be done with it, with good quality blades you could keep the breakages down to a minimum. There was a maker of electric scroll saws in Europe who sold blades to be used with it and I made the mistake of buying them once. I used a bakers dozen blades just cutting out one end plate, whereas with the good quality jewelers blades I may break one per plate. One thing that helps is candle wax on the blade or rubbed onto the template, but without the compressed air it will cause the sawdust to accumulate in front of the cut making it hard to see the lines. I have also tried cutting the end plates out using a router but I was not happy with the result, and by using templates and hand saw the templates could easily be adjusted to correct size required on the computer.
 All my templates are on Excel spreadsheets, as it is a fantastic stable program that will take and adjust big images without crashing.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 21, 2013, 07:31:26 AM
The corner blocks I now fit are not designed to give the frames strength they are for the end-plate screws to hide within, I try to keep all screws on the outside of the instrument to an absolute minimum. I feel it after all the work that goes into the woodwork I do not want screws spoiling the effect. At this stage I drill down through them and the bulkhead with a small drill.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 29, 2013, 10:28:22 AM
Next stage is for me to glue the end plates down to the accordion frames. I then run the whole thing up against the router bench and router around the edge and give it a 5 mm radius. I then cut off the end plate using a fine slot cutter in the router, I cut about 10 mm below the end plate or around the red band area, by doing it this way you know the end plates will match the accordion frames.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on July 29, 2013, 10:31:00 AM
Using an 8 mm drill bit I counter drill down about 7mm into the end plate corners and insert leather plugs into the holes, these make fantastic screw “nuts” as they do not strip the same way as if you were screwing straight into the timber.
I then drill from the bulkhead side up into the screw corners using a specially made drill bit, it’s a 7 mm drill with a 25mm in length 3.5mm leader drill, with this bit I know how far my screws will protrude into the end plate nut.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on July 29, 2013, 03:19:05 PM
Fantastic - this box is really coming together ! . as I said before, it`s great to see this happening as a series on Melnet . thanks Stormy ...........
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 03, 2013, 09:30:28 AM
Fantastic - this box is really coming together ! . as I said before, it`s great to see this happening as a series on Melnet . thanks Stormy ...........
That's nice to hear, its easier writing about it than making it; at times!!
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: blafleur on August 04, 2013, 01:53:09 PM

I did forget to mention that Bryan Lafleur in Texas had tried the balsa, and the feed back I had from him was very positive, but my mind had been on the bigger European makers.

I did build one with some balsa.  The body was instrument grade spruce, and the reed blocks were balsa.  It was very light, and had a very rich, sweet tone. I showed it around a lot, with good reviews, but I learned to wait till the player tried it before telling them what it was made of, or they had preconceived ideas.  I always them I got the idea from a trail blazer in Australia.

Enjoying the photo series, Stormy!
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 05, 2013, 12:27:46 AM
G'day Mates Thanks for the feedback
I have a text problem with the next post, and Clive is looking into it.
As it turns out the photos were the problem so I re named them.
Treble Mechanism is now ready for fitting the ends.
I have cut the mechanism at the ends with a 5 deg slope inwards, if you go any further than that gluing the ends on can become more of a pain, as the ends will want to slide up on the glue. I tilt the mechanism back 15 deg and just put a couple of veneers underneath so when they are taken out after the glue up the treble mechanism ends are then resting on the frames. I have found by doing this it protects the bulkhead when the instrument falls from a great height off the stage, or some drunken bell hopper drops it.
After I have fitted the ends I then cut them back to about a 7.5 deg angle.   
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 12, 2013, 01:20:35 PM
The button rods on the bass side are made from 2.0 mm wire imported from Italy, I was using 2.4 mm bronze welding rods in the long distant past. It is very hard these days to get the older trade stock like wire and extrusions, so I got 10 kilo of each size wire that I needed 2.0mm 2.2mm and 2.4 mm, it is sold in 1-meter lengths.

I have a bending jig for each width of instrument, this picture is of my 150 mm wide jig, you can do each size on the same jig but you end up with far to many holes and you do not know if you are “Arthur or Martha”.

I have a few button shanks where I have drilled a 2 mm hole all the way through, I place the shanks within each bush with the wire passing through it, this allows me to line up the rod in the right angle before I cut off the excess, you should be able to see the shank and the excess rod within the photo.
Button shanks are fitted to the rods using Feraltite (used in Archery and Fishing) it is a hot melt resin and is better than glue.
Where the rod fits into the leaver holes I use the rubber spline to keep it in place, I just give it a little spit and that then holds on very well, just as well that I had 100 meters of it made at the time.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 12, 2013, 02:05:52 PM
I’m now ready to look at spraying the job, the photo shows all the parts that I have made, ready for striping down and then fitted to holding jigs for the spraying.

Next photo shows the gear that I use when I’m spraying there is another two filters at the end of the yellow hose, here is the warning; I will not even open up a tin of spray without that gear being worn, two pack is highly toxic to the body and will track right into the blood stream, this also goes for araldite and plastibond type products, the hardener is very dangerous, and it is the same stuff that is used as a hardener within the spray, so always wear gloves and goggles when using that filler or synthetic glues.

Even when I sand down I use the breathing gear with a half mask so there is no way I get that dust within my lungs.

It’s a little ironic that I use full gloss and I do all my spraying within the dirty workshop with sawdust all around without a booth with doors open to the elements and sometimes it’s a little windy, but still I get a good clean job and I can get away with it “off the gun”.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on August 12, 2013, 02:08:28 PM
Great to see it all in one place ready for spraying and assembly - looking forward to seeing the reeds being waxed in those foam blocks . I`m sure Nudiefish is also  :M
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 12, 2013, 02:39:34 PM
I forgot to show my corner fillets, these are put in on the corners of the accordion and bellows frames, I use the slot cutter on the router table to make the slots.  It is these that on the whole give the strength for holding the instrument together. I rely on the instrument springing apart if it is dropped from a great height, that way it does very little damage, as you do not get torn timber, except for the fillet. I can then re fit the fillets by using the router to cut them out and re gluing new ones in. But interestingly I had a customer whose instrument was placed on the kitchen table (during a very drunken party) on its bass side, I do not fit feet to the bass side so it rolled off and landed bass side down on a slate floor, and the bass strap caused a crack down the end plate, but all the frames held well.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 12, 2013, 02:50:26 PM
Great to see it all in one place ready for spraying and assembly - looking forward to seeing the reeds being waxed in those foam blocks . I`m sure Nudiefish is also  :M

I sent him a DVD of the final product being played in all its variations last week and he should be watching it right now, trying to make up his mind how he would like me to set it up for him in the first instance. He has a choice of TTT or TTB with a trad bass or a Hyde bass for starters. I have made a complete extra set of bass reed blocks and another 3rd voice reed block for the treble side, that I will send with the instrument for him to change over if and when he wants.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Nick Collis Bird on August 12, 2013, 03:35:24 PM
Peter, what sort of prices do you charge for these fantastic instruments ?
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on August 12, 2013, 03:35:51 PM
the weak-spot (fillets) looks a good idea, reduces the damage on a fall - Why no bass feet ?, everyone I know dumps the box on the bass end ..

I was also wondering about bellows, can`t remember if you made your own or bought in Italian, Slovenian ones etc ..
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on August 12, 2013, 11:26:17 PM
I'm careful not to throw spoilers into the mix at this point because this thread has turned into an excellent exposition how a craftsmen can turn wood, wire, foam and tiny bits of metal plate into a object of beauty and wonderment.  I will say that I have seen a photo of the finished product and have also communicated with Mr Hyde's test pilot - the guy who put it through its paces and a chap well known for English music in this country.   The photo is currently hanging on my office wall and I can't stop looking at it.  The word from the musician who tested the box - well, he said that it was one of the finest machine's he's ever played.  The CD Stormy sent me of it being played has yet to arrive (probs today) and I'm burning to hear it.    In a short while I shall have the instrument in my hot, sweaty hands and I shall be in heaven. 

You guys put me onto Stormy in the first place, thanks heaps!  I'm happy to show it off in due course - but not before he has finished this fascinating series.

It is like a striptease, but in reverse!

 :||:

Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 13, 2013, 01:06:31 AM
the weak-spot (fillets) looks a good idea, reduces the damage on a fall - Why no bass feet ?, everyone I know dumps the box on the bass end ..

I was also wondering about bellows, can`t remember if you made your own or bought in Italian, Slovenian ones etc ..
The reasons that I do not fit feet on the bass side is that due to the padded straps and both ends go within the instrument they would have to be very big as the bend in the strap takes a lot of space, and there is a lot of hardware on the bottom of the instrument that protects it when you put it straight down, you will see some of my photos are taken on a stone wall and there is no problems with that even with a very new finish.
I get my bellows made in Italy, where I can order any size down to the mm, I used to get them from East Germany before unification, and there are still plenty of them playing a good tune. Although I started my career 35 years ago as a concertina bellows maker and have made the same sort of bellows for a couple of accordions they are far to expensive to make that way.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: smiley on August 13, 2013, 02:25:26 AM
I probably shouldn't be telling you this - but some lucky person [hopefully ME] will be getting a new Hyde box for an outlay of $5.

There's a raffle being drawn in Adelaide on 21st December 2013 - see www.spiraldance.com.au/?download=Ale%20Raffle.pdf‎
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on August 13, 2013, 06:54:06 AM
Excellent - I`d not want to make bellows either, the Italians have it off to a fine art .. looks like its all coming together beautifully ;D
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Owen Woods on August 13, 2013, 08:53:34 AM
I probably shouldn't be telling you this - but some lucky person [hopefully ME] will be getting a new Hyde box for an outlay of $5.

There's a raffle being drawn in Adelaide on 21st December 2013 - see www.spiraldance.com.au/?download=Ale%20Raffle.pdf‎

I think you'll find that the lucky person will be me.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: brianread on August 16, 2013, 07:58:14 PM
I probably shouldn't be telling you this - but some lucky person [hopefully ME] will be getting a new Hyde box for an outlay of $5.

There's a raffle being drawn in Adelaide on 21st December 2013 - see www.spiraldance.com.au/?download=Ale%20Raffle.pdf‎

I think you'll find that the lucky person will be me.

or me!! (:) (:) (:) (:)
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: deltasalmon on August 16, 2013, 08:04:28 PM
I probably shouldn't be telling you this - but some lucky person [hopefully ME] will be getting a new Hyde box for an outlay of $5.

There's a raffle being drawn in Adelaide on 21st December 2013 - see www.spiraldance.com.au/?download=Ale%20Raffle.pdf‎

I land in Sydney on the 21st! I should buy some tickets since I'll be in the neighborhood and won't have to pay for the shipping to send it back...
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: brianread on August 16, 2013, 09:28:13 PM
I land in Sydney on the 21st! I should buy some tickets since I'll be in the neighborhood and won't have to pay for the shipping to send it back...

I got the impression that the prize included the shipping...
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: deltasalmon on August 16, 2013, 09:32:36 PM
I land in Sydney on the 21st! I should buy some tickets since I'll be in the neighborhood and won't have to pay for the shipping to send it back...

I got the impression that the prize included the shipping...

Adelaide is about a 14 hour drive from Sydney so that's not working in my favor either...
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 17, 2013, 11:17:28 AM
Peter, what sort of prices do you charge for these fantastic instruments ?
Sorry I have been a little slow here;
The easiest way to explain this is that my instruments range from $3500 - $6000 Ausy it is dependent on what you want on board, but most customization is done without extra cost, and I have 100% money back guarantee if the customer is not happy with the instrument, no questions asked (but I would like to know where I failed the customers needs), that also includes the post.

The biggest instrument I make is the same size as the poker work 280mmx150mm and within this size I can get 36 keys 2 voice or 25 keys 3 voice with stops, bass side 12 bass with stops. I have made a couple of instruments for the Dutch customers and they were 33 treble x 14 bass.
All instruments come with my lifetimes guarantee on all parts I make, I will pay for postage both ways in the first year, after that we split it, I will even do 8 hours work free of charge if you damage the instrument.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on August 17, 2013, 11:29:10 AM
Wow, that`s gotta win a good service award !! .... $3500 Aus is hardly what you`d call expensive for a bespoke box of this calibre either .
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 19, 2013, 10:20:20 AM
I use high gloss two pack polyurethane spray in a workspace that by rights should not work, as there is plenty of sawdust in the air, but for some obscure reason I get away with it and I get the finish “off the gun”.
I tend to fill any small imperfections with araldite as this does not hide the timber, sometimes I might use colored wax, or chips of the same timber.
I start by just putting a thickish first coat without to much worry about finish, as this coat will be almost sanded off again. I use only hand block sanders and 3M sanding pads (that I get from the automotive crash repair suppliers,) and steel wool, if there is any gloss left on the surface for the next coat it will pucker up at this point. Stay away from “wet and dry” as you can end up with black grit in the grain.
 The hardest things to get rid of is “fish eyes” in the lacquer, on the whole they are caused by vapors or silicone contamination, there is only one thing to do here, sand the finish right back to timber as the fish eyes leave marks in the coats underneath that are noticeable if you spray over them. 
I have made up hanging handles so that I spray in the hand then hang upside down from the roof.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 25, 2013, 12:36:22 PM
After I have got the finish that I want I then cut out and fit the logos. These logos are solid silver 0.3mm thick. Once I have cut them out I then stick them down to a spray card and then give them a few coats of spray.  I then use double-sided tape to stick them onto the instrument face. I then spray them in using very good thick coats of lacquer over them so they will not get caught on clothing. The thing about silver is that not much wants to stick to it, and that includes most glues, I tend to use craft glue to stick the templates down onto the silver. There is something very special about silver logos that can only be seen while on stage and that will blow away the audience.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Nick Collis Bird on August 25, 2013, 12:55:14 PM
Peter, truly fantastic. Plus the fact the lacquer will stop the silver tarnishing.
As for double sided tape, I had my doubts about its longevity as a bookbinder so I took a coffee mug and stuck it to the workshop door with this tape . That was twenty years ago and it's still there. However, the British Museum ( one of my clients) still won't accept it. They need fifty years to prove a "new" substance is acceptable.
  By the way, if I win the national lottery, I shall be next in the queue for one of your boxes.   ;D

PS. You don't do Limericks, do you?  >:E
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on August 25, 2013, 01:05:00 PM
Peter, truly fantastic. Plus the fact the lacquer will stop the silver tarnishing.
As for double sided tape, I had my doubts about its longevity as a bookbinder so I took a coffee mug and stuck it to the workshop door with this tape . That was twenty years ago and it's still there. However, the British Museum ( one of my clients) still won't accept it. They need fifty years to prove a "new" substance is acceptable.
  By the way, if I win the national lottery, I shall be next in the queue for one of your boxes.   ;D
Thanks for that.
Polyurethane stops the tarnishing, but this is not not the case with acid catalytic. The double sided tape is very good but on the whole the logos are held in place by the lacquer, that puts a very strong coat over the whole lot.
All I can say is; "all the best in that lottery"
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on August 25, 2013, 01:05:15 PM
as you`ll know better than anyone Nick, there`s tape and tape .. some is "real" tape in that it`s an adhesive on both sides of a plastic backing and there`s the type which really is merely adhesive in tape form - I'd choose the latter
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 03, 2013, 01:39:38 PM
After spraying I let the lacquer cure for a few days, how long this takes is very dependent on the weather.
After this I assemble the instrument and then cover it in masking tape to protect it over the next few stages, if you put this on before the lacquer has cured you can have a hell of a trouble getting it off.  When you get to the stage of taking it off then go over the surface with a damp cloth of mineral turpentine, it will make the removal very easy.

Next stage is laying out the reeds for valving and tuning. It is very important to have a system here, so if you go away for a month on holidays you can take one look at the reeds and they will tell you at what stage you are at as far as tuning is concerned.

For sticking the valves down I use the good old Selleys craft glue, it will even stick those sequins and buttons on to your “Pearly King” gear.
http://www.selleys.com.au/adhesives/household-adhesive/craft-adhesive/
At this stage I tune all reeds on the bench at least twice, first time to get them close to the mark as possible, and the second time to catch up on any “drift” that might have occurred overnight. It is after this stage I wax them into the reed blocks.

I know some people are going to say the reeds should not be tuned until the reeds are in the instrument, my reason for this is it allows me to “read the instrument”, if I had not tuned the reeds before I put them into the instrument I would not have any idea as to what the instrument is doing. This time after re checking the tuning on all reeds I found that there was a group of reeds in one spot that were slightly flat, by reducing the tension very slightly on the reed block the tuning sharpened up again at that point. I always look for other reasons why the instrument might be thrown out of tune other than just reed tuning, and on the whole this has become very intuitive on each instrument and hard to pass on.
After I have “tuned the instrument” I now go through and check each reed and give the reeds their final fine tune on the reed blocks.

So on the whole the reeds are checked and tuned in 3 stages.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Chris Ryall on September 03, 2013, 01:43:03 PM
Nice example of the little weights on the ends of the really deep (bass?) notes. Someone was a bit incredulous in another thread when I described these.

Not far to go now, then?
   (http://forum.melodeon.net/index.php?action=dlattach;topic=12263.0;attach=11997;image)
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 03, 2013, 01:51:30 PM
Nice example of the little weights on the ends of the really deep (bass?) notes. Someone was a bit incredulous in another thread when I described these.

Not far to go now, then?
Glad you like it.
Not far to go, but the next stage was far harder than expected.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on September 03, 2013, 03:28:40 PM
It`s looking superb, and really coming together ! . thanks for keeping the series going

Those weights on lower reeds are quite large on "outer rows" Boxes (A/D, G/C) with low notes .
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: diatonix on September 03, 2013, 05:54:19 PM
Thanks for an interesting thread which is, of course,  right down my alley. In case it's not a craftsman's secret, I'm curious to know the brand and category of the reeds.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 04, 2013, 02:11:42 AM
It`s looking superb, and really coming together ! . thanks for keeping the series going

Those weights on lower reeds are quite large on "outer rows" Boxes (A/D, G/C) with low notes .
They might be large but they work well on good quality reeds.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 04, 2013, 02:22:03 AM
Thanks for an interesting thread which is, of course,  right down my alley. In case it's not a craftsman's secret, I'm curious to know the brand and category of the reeds.

I just buy best quality "professional reeds" and on my shelves there are a few reeds from various makers.

My feeling is that if the "box" is not right then no matter what reeds go into it they will not help much, and if the "box" is good then the "professional reeds" will make a difference, that's why I find it very important to "tune the box".
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 09, 2013, 01:36:09 AM
As mentioned this stage was a bit of a surprise for me; when nudiefish asked me to fit a “mike system” I just said, “yes” without thinking much about it.
When I came to start to fit it I came to the very fast conclusion that I had never put one into this smaller size box (240mm x 150mm) that had 12 bass and slides, this causes the reed blocks to take up every last mm within the bellows cavity giving me very little room to move for the cabling down the inside of the bellows, eventually after a very frustrating day I got there with it.

Because of the 12 bass in such a small box I even had to put the stereo socket in a place where I would not normally do so, this time I had to have it fit within the bass mechanism rather than bellow it.
If I ever have to do this again on this size box, then I would run the first half of the cabling across the back folds then revert to the top for the next half.
After the initial frustration it works very well.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on September 09, 2013, 07:22:55 AM
Hi Stormy, Neat Job ! ...... the bass reedblocks look like wood ?
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 09, 2013, 08:19:41 AM
Hi Stormy, Neat Job ! ...... the bass reedblocks look like wood ?
Thanks.,
In fact the chord block has a veneered capping to give stiffness to the block. If you look very closely at the right end of the chord block you can see the veneers and the pink foam bellow, on the fundamental block you will see on the front edge above the higher reed the veneers within.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on September 09, 2013, 08:37:16 AM
Ahh right, got it, I wondered what you did to the foam to stiffen it . the Sole plate is wood anyway isn`t it .. Looking forward to pics of the finished foam treble reedblocks with the reeds fitted :)
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 09, 2013, 10:22:16 AM
Just had a quick look at my files and the only picture I have that shows the reed blocks is this one
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on September 09, 2013, 03:08:02 PM
Thanks .. looks good ! . nearly there !
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 13, 2013, 02:54:18 AM
Here we are; the instrument is made, recorded and sent to the new owner.
By supplying extra reed blocks, this box now has the option on the treble side of TTT or BTT. On the bass side the option of a Traditional Bass or Hyde Bass System.

Nudiefish has been great to work with, as he has appreciated the fact that he can have as much input into the construction of his box as he wishes, and my mate Paul has been a great help as the test pilot.
This has been a very enjoyable project all round, and its time for me to put up the feet for a week or so.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Adam-T on September 13, 2013, 07:06:58 AM
Excellent Stormy, it looks superb inside and out - thanks a lot for this series, it`s been a unique insight not only into the art of bespoke box making step by step in real time but more to the point, showing your groundbreaking designs and ideas proving that rather than just copying Hohner or the Italians like others have done (Chinese, Harmona etc) , a bit (well err, a lot really) of originality goes a long way ..
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 13, 2013, 09:05:37 AM
Excellent Stormy, it looks superb inside and out - thanks a lot for this series, it`s been a unique insight not only into the art of bespoke box making step by step in real time but more to the point, showing your groundbreaking designs and ideas proving that rather than just copying Hohner or the Italians like others have done (Chinese, Harmona etc) , a bit (well err, a lot really) of originality goes a long way ..
My pleasure.
I had the good luck of living a long way from other makers.
At first I started by copying the old Mezons, single rowers, two rowers, and 3 rowers, but after a while i came to realise that I was copying their mistakes, from that point of time I decided to "free fall" and not get overly influenced by other makers work.

 Accordions are just about the only instrument where there are no books printed on the making of the same, all is kept in house (you never see Italian makers on discussion groups; unless I missed them,) and you have to let go of all the pree conceptions and start from afresh.
The other thing about making is that one has to enjoy making mistakes, it is very strange that I revel in it, because sometimes and more often than not it will take me down a road that will produce something that is very beneficial, you have to keep looking out of those side windows for the unexpected. Sometimes people will make a comment that seems silly at the time, but can turn out to be a fantastic idea if you just give it a go.
I have made over 300 accordions in the past lifetime, and even now I can say that ideas have come and gone and come back again in another variation. You have to be willing to look back over the shoulder and not always ahead, as something you discarded years ago can now fit together with some other knowledge created today.
"There is no right way or wrong way to make an accordion, some will be better or worse than others".
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on September 13, 2013, 11:33:18 AM
Hello Fellow Squeezers,

It's about to break into the weekend downunder and I have been busy laying turf in the backyard for the spring, so I will advance my Hyde story slowly and as time allows.  I have kept (mostly) quiet about the project here so as to allow Stormy to explain things without me getting ahead of the game.  He has advised that it is safe for me to spruk about the box now without me upsetting the apple cart. So, I will start. 

I've had the Hyde box about three weeks now and it has exceeded my already high expectations.  I'm still getting used to playing it, my previous experience has mostly been limited to my several Hohner Ericas.  From that point of view, it does play very differently.  The various switches give me way too much choice for experimentation and if I could only resist changing the settings every five minutes I'm sure that I would have advanced further than I have to date.  It goes something like this:  I play a tune with everthing engaged - all three voices, including the fabulous bassoon block, then I cut out the bassoon voice and play it again with the two voice TT, afterwhich I exchange one of the treble voices back to a bassoon for the "octave jump" mode, then I play the single voice for the same tune - and next I hit on the bass side and cut out the thirds and play it again, and to finish I cut out the fundmental as well so that it is pretty much nude (the sound, of course, not me).  After all this I take off the bellows and put them on back to front to see what the effect I get from doing that (actually, I don't get much out of it at all).  This is the reason why my playing progress is so slow. 

I'll include a short You Tube vid of the new Hyde box playing with all the switches engaged.  Knowing the quality of the musicians on this site makes me feel the full weight of unrealistic expectations.  My own unrealistic expectations, that is.  For the fluffs on the clip, please blame me rather than the box - in time I shall grow into it, but that date has yet to arrive.    Lastly, I intend to try my hand at writing a Hyde box review - once again, it will be low on the technical side and high on playability, function and sound.  Probably a fair bit of emotion too, because that is the real reason why we play the box above all things.  I listened to a clip of Andy Cutting yesterday and after two minutes I had stopped listening to him play the box and began hearing him play music.   I think that there is a difference.   

Without further ado, here is "Nutting Girl" on a Hyde machine:

 http://www.youtube.com/watch?v=BjLCKboDoKM (http://www.youtube.com/watch?v=BjLCKboDoKM)



Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on September 13, 2013, 11:58:35 AM
"There is no right way or wrong way to make an accordion, some will be better or worse than others".

Absolutely true, and in some way it always terns out that everyone will be a little bit different, even if it is one of a range of the same production if more as one is made the same time. As Time goes on more accordion maker will use CNC and Laser Cutting for nearly all wooden parts that lead to a bit less of individuality. A handmade Box like Peter Stormy makes is from this point especially very special.

Thanks Peter i hope we here more of you once you start on the next box. Johann Pascher
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Lost Alamos on September 13, 2013, 12:37:22 PM
To the builder and the owner a big congratulation
and what Johann Pascher said goes for me too.
LA
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Chris Ryall on September 13, 2013, 01:00:37 PM
Looks great, guess I don't need to remind you to wax that last right end reed in (previous pic)  ;)

… another satisfied customer  :|glug
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: EastAnglianTed on September 13, 2013, 01:09:41 PM
    Wow fantastic work, and congratulations to the new owner too!
    P.S. And thanks for fulfilling my lust for seeing melodeon construction in action with your great pictures along the way! Really great!
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: an bosca ceoil on September 13, 2013, 04:18:41 PM
Looks great, guess I don't need to remind you to wax that last right end reed in (previous pic)  ;)

… another satisfied customer  :|glug

Ten are sufficient on that block?
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: diatonix on September 13, 2013, 04:22:26 PM
" As Time goes on more accordion maker will use CNC and Laser Cutting for nearly all wooden parts that lead to a bit less of individuality"
Fortunately, this statement doesn't make sense at all.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on September 13, 2013, 06:16:13 PM
" As Time goes on more accordion maker will use CNC and Laser Cutting for nearly all wooden parts that lead to a bit less of individuality"
Fortunately, this statement doesn't make sense at all.
The statement is naturally from my few point. I only tell what i did see in the production of boxes at the time i did visit various builders in Italy, Slovenia, Austria and Germany the past. I personally don't use CNC or Laser Cutting on the wooden parts. I did not build as many boxes as Peter, and so for this small number of boxes i did not see a need for it, and i anyway enjoy making nearly everything my self.  I just started on making two new four row Austrian style Helicon boxes and i don't have a hurry. At the moment i did do the preparing of the wooden frames for the box. If any one is interested i also my tell step by step how i go along.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: EastAnglianTed on September 13, 2013, 06:30:35 PM
At the moment i did do the preparing of the wooden frames for the box. If any one is interested i also my tell step by step how i go along.

    Please do! These kind of threads are very very interesting and useful.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Peter Stormy Hyde on September 14, 2013, 01:59:28 AM
Looks great, guess I don't need to remind you to wax that last right end reed in (previous pic)  ;)

… another satisfied customer  :|glug

Ten are sufficient on that block?
Yes I keep the "blind cavity's" as much as possible.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Owen Woods on September 16, 2013, 11:26:41 AM
I think that in something like a fiddle, controlling everything about the build is arguably not a good thing, because it limits the range of instruments (and therefore the range of customers) that a luthier will generate. For a melodeon though, precision in building, not just in manufacture has to be a good thing. A good custom maker will be able to adapt to each client and deliver a box which is utterly individual to them. The fact that it is precisely made with CNC and laser cutting doesn't affect the individuality of the instrument at all. I am full of admiration for those who can build completely using hand tools, but to me, CNC and laser cutting is just a natural extension of the concept of a jig, which lets the craftsman build quicker and spend more time being creative.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Cag on September 16, 2013, 03:21:55 PM
Cnc is a tool just like a saw. No one would criticise a person for using a powersaw rather than a handsaw to make an instrument. CNC is just another step up in the tool chain.

In the end, cnc or not, the instrument is a reflection of the design which comes from the maker's head and reflects their experience. Cnc makes it easier to avoid manual mistakes, and if manual mistakes equal quality something is awry.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: Owen Woods on September 16, 2013, 06:00:15 PM
By the by nudiefish, nice sound on that box! But remember that you can take your fingers off the bass from time to time ;)
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: nudiefish on September 17, 2013, 09:14:14 AM
Thanks, ukebert, I'll try and take that on board.
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on September 22, 2013, 04:43:02 PM

I have made the fist few pictures about the building process.
My be is better i open a new thread.
At the moment pictures are on my facebook page.

https://www.facebook.com/media/set/?set=a.661706320513827.1073741827.100000233943577&type=1&l=0a0fedbeb8

best regards, Johann
Title: Re: See "Posh Box" being built for "nudiefish"
Post by: JohannPascher on September 29, 2013, 11:46:50 AM

At the moment pictures are on my facebook page.

https://www.facebook.com/media/set/?set=a.661706320513827.1073741827.100000233943577&type=1&l=0a0fedbeb8

I have now created my on thread about my project to keep this away from this very interesting thread.
See:
http://forum.melodeon.net/index.php/topic,13284.0.html

About the question that is discussed here at the moment:
"The only problem i can see so far is that the little coils would mean there will be a lot of cabling moving around that is not anchored, and could end up between the reed blocks."

I also would think so, but one could give it a try. I think the distance between one side and the other of the bellows frame is  not long enough for the collapsed  coil. First one would need a nice wire coil with the amount of wires in it as the are needed.
How many single wires are in it?
Is such a coil available somewhere?
Will the coil keep its springiness over time?
I am also not sure if the wire will finaly with fast bellows movement still get caught?


Best regards, Johann Pascher
SimplePortal 2.3.5 © 2008-2012, SimplePortal