Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3 4 5 6   Go Down

Author Topic: See "Posh Box" being built for "nudiefish"  (Read 30286 times)

0 Members and 1 Guest are viewing this topic.

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
See "Posh Box" being built for "nudiefish"
« on: May 05, 2013, 10:35:41 AM »

Following the discussion with “nudiefish” about a custom made melodeon on the site, I thought it might be a good idea to show the steps involved in making the “Posh Box” from order to inception. There will be a few photos, and any replies within my text from “nudiefish” will be in blue text.
As I’m now in semi retirement!!!! There are no more 60-hour weeks.

Original Order;
Key D/G  21 button 3 voice (TTT) French Musset, 3 stops. 12 Bass 2 stops.
Size 240mmx150mm.
Timber; Frames “Birds Eye Rock Maple” End Plates and treble mechanism; Masur Birch, none in my stock or in Adelaide, replaced with Quilted Sycamore (cut before 1913.) Contrast; “Jarrah”   
Keyboard; Raised with 15 mm buttons. Bass side; 15mm buttons
Strap system; Double.
Fitted with on board Mike System.

Daily log;
Day 1
Make up blank frame with “Jarrah” side rails
4 hours
Day 2
Frame blanks are ready for ripping down.
End plates and bulkheads glued up and finished.  End plates made from “Queensland Red Cedar” core with two veneers on either side, two “blue” blind veneers athwartships, and the outside 2 fore and aft, Bulkheads made from gluing together two 1.5 mm sheets of aeroplane ply, external grain running athwart-ships.
7 hours
Photo 1 shows blank frames before rip down.
Day 3
Removed end plates from under press, they had been there far too long (I hade the day off between clamping and removal) so mildew on hidden veneers, one bubble where it had not stuck down so used the iron too fix down, this works well on PVA glues.

I call the veneers inside the box “hidden” and the ones between other veneers or timber as “blind”.

Rip cut the blank frames using very fine blade (blank was only 11.5 mm thick and I needed 5mm for each frame, and the blade had 1mm kurf) but went very slowly and it worked very well, not much sanding needed and frames were finished in the thickness sander to 5mm.

One side of frames were coated with red oil, made from the gum of the Yakka tree native here in Australia, this highlights the reeds within the timber but does not stain, this allows choice after spraying as to what side the customer wants on the outside.

Treble mechanism was glued up ready for spraying.
Bass button riser cut and blind drilled.
5 hours.
Photo 2 shows frames after rip down and sanded with Red Oil sent too “nudiefish”.
Thank you very much for sending me that shot.  I simply love the frames. I've blown up the image so as to better take in the pretty maple lines and all that swirly detail.  Plus the rich red borders are lovely.  I'm going to enjoy the look of this box just as much as the sound of it. 
Secondly, I love the idea of you documenting the making of the box.  Actually, having a pictorial record of it being made is quite a special gift. I don't think that there would be very many people in the world who could produce images of their squeeze box being born, and in living colour too.  And posting the results to the melodeon site is also an excellent idea and one worth pursuing.  These guys live and breath melodeons and I agree there are many who would be thrilled by the notion of seeing a melodeon grow out of nothing.  I know that I would!
Anyway, thanks Stormy, please go ahead, and look forward to watching my box come to life.   
Cheers,


« Last Edit: May 13, 2013, 11:11:21 AM by Peter Stormy Hyde »
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

nudiefish

  • Member
  • *
  • Offline Offline
  • Posts: 40
  • Aussie Morriser
    • Art Prints
Re: See "Posh Box" being built for "nudiefish"
« Reply #1 on: May 05, 2013, 11:29:36 AM »

Thanks Stormy, looking forward to seeing the box develop.  I'm actually leaving for Europe in a few days so I will have to catch these installments on those rare occasions when I stumble upon free WIFI. 
Logged
1 x Hohner D/G, 1 Sandpiper Stint D/G and a Hyde D/G Box.  I'm also a photo buff!

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: See "Posh Box" being built for "nudiefish"
« Reply #2 on: May 06, 2013, 10:22:49 PM »

Very nice!

I've heard rumours about exotic woods being difficult to import, even when they are part of an instrument and from a stock like yours, rather than being illegally logged. Have you had any troubles with that?
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: See "Posh Box" being built for "nudiefish"
« Reply #3 on: May 06, 2013, 10:41:53 PM »

The desk under my computer is made of an old recovered kitchen, itself a recycled 1950s school  chemistry lab - "ironwood" I'm told.

But you can only plumb in square sinks  ;)
Logged
  _       _    _      _ 

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #4 on: May 07, 2013, 01:09:36 AM »

Very nice!

I've heard rumours about exotic woods being difficult to import, even when they are part of an instrument and from a stock like yours, rather than being illegally logged. Have you had any troubles with that?
Thank you.
Yes; there is now a problem along those lines you mention, even if it is recycled timber, but it is a little strange as some of the very threatened Australian species are not on that list. I have a big stack of off cuts of Brazilian rosewood that came from a guitar maker some years ago, so i would not use that on an export instrument.
I think I'm safe with the timbers on this box.
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #5 on: May 07, 2013, 01:15:57 AM »

The desk under my computer is made of an old recovered kitchen, itself a recycled 1950s school  chemistry lab - "ironwood" I'm told.

But you can only plumb in square sinks  ;)
I once had a customer send me the timber from a toilet door from an old derelict farm where he was born up in Northern NSW, the timber in that door was Queensland Rosewood, Queensland Ceder and Blackwood, obviously the customers grandfather who built the farm house had good taste.
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #6 on: May 13, 2013, 08:15:00 AM »

Day 4
Sand down and spray all parts, this is done so that I get a good finish on the inside, and the outside is protected from scratches and glue.
8 hours

Question nudiefish; would you like the darker leaver stock as seen in front of the mechanism or would you like the sycamore again, my feeling is the darker would look good.

Thanks for providing an update on my box, Peter.  I actually look foreword to watching our project develop and grow and I love the look of the thing.  It is indeed beautiful, and I agree, please keep the dark wood as you have it.  Having a blond box allows a very sweet red colour to set it all off.
I must admit, Stormy, that ever since playing your other box and hearing that resonant deep bassoon sound it has me thinking.   Either way I can't wait to get my hands on your creation.


Day 5
Cut trenches on inside of frames and then cut down to size, and fit corners. Fix risers to leaver stock. Start cutting slots for treble leavers in Treble Mechanism Block.
4 hours
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: See "Posh Box" being built for "nudiefish"
« Reply #7 on: May 13, 2013, 08:20:32 AM »

This is going to be one beautiful Box Stormy - thanks for the updates !
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #8 on: May 13, 2013, 10:49:01 AM »

This is going to be one beautiful Box Stormy - thanks for the updates !
Thank you Adam-T

Day 6
Finish slots in treble mechanism, and glue on capping. Fit bulkheads to frames, and then router out the holes. Make reed block shoes. Extra reed block shoe was made for the treble 3rd voice  reed block, as I will also be making a bassoon reed block, so it can be swapped for the 3rd voice tenor.

You will notice that I use an overhead router (in fact it is a heavy duty grinder) to router out the holes, the stand and the grinder have served me well as they are over 30 years old.

The radial arm saw is used only for cutting the slots on the mechanism, and nothing else. I have had a couple of blades made with V tips so the spring goes center in the slot.
I set the saw up again for the photo so I would not normally use it with the block sander behind the fence, and of course the capping was put on after the slots were cut.

And the real stupid thing here is I have just made a 23 key mechanism for a 21 key instrument, it is possible to cut a bit off the ends and slide it into the slot without being seen, but this time I will make a new one. Automatic mode can be deadly at times.
4 hours
 
« Last Edit: May 13, 2013, 11:15:17 AM by Peter Stormy Hyde »
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #9 on: May 26, 2013, 11:33:05 AM »

Day 7
Back "on deck" after getting called on to another job.

The first photo shows the bulkheads fitted to the frames, at this stage they are held together with rubber bands. I always make the bulkheads  slightly oversize then i cut away what is needed at the back and bottom edges.

The second photo shows the slides fitted to the bulkheads using cardboard as spacing material*
*Now before you all throw your hands up in the air that cardboard is used by the British Museum for numerous tasks and one of them is the stiffener within leather bound books, it is acid free and the edge that is cut by a guillotine is as hard as any timber . This cardboard was purchased by me 35 years ago to make concertina bellows, and it worked very well for that job, I bought a pallet load of the stuff. It has been stored in the roof of the garage for all that time and is still as good as the day i purchased it, so it is very stable. If anybody is looking for this cardboard I would suggest that you get in touch with your local book bindery, then that might now be in China, but I'm sure the bindery at the British museum will be helpful.

I glue the cardboard over the holes and then quickly cut out the holes using a fret saw, i could put them back under the router, but the saw does a cleaner cut, do not use blades from the hardware store go to a jewellery suppler and get good quality fine blades.

 
« Last Edit: May 26, 2013, 11:36:07 AM by Peter Stormy Hyde »
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: See "Posh Box" being built for "nudiefish"
« Reply #10 on: May 27, 2013, 07:59:46 PM »

Coming on Nicely Stormy - keep the shots coming !!
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #11 on: May 28, 2013, 12:33:53 AM »


Coming on Nicely Stormy - keep the shots coming !!
Thanks for the encouragement.
Day 8
Fit reed block shoes on bass side
Glue up treble reed block blanks. With this I work with a height of 300mm, as this is what will go under my book press. I start by cutting the dividers needed I always make it a 12 cavity reed block, and as my treble buttons are spaced at 18mm I then have a 14mm cavity with a 4 mm divider.  So with this in mind I have laid out strips of 14mm craft board glued down to a bed of ply with slots left in between for the dividers. I now insert the strips into the space for them then I glue down a sheet of dividing bulkhead that is 5mm thick  (there is good reason that it is so thick as I’m always working at getting a 3 voice box into an instrument 150mm wide,) I then place this under the book press for a few hours, then I repeat the process on the other side. I now have what I call my “reed block blank” ready to slice off any size I require.
Yes I know it does not look like timber, it is not; it is in fact foam that is used in boat, shipping, and aerospace industries, so it is of a very high quality specification and has no acoustic quality’s at all, it is dead as a Dodo and that is what is needed so that it does not interfere or scavenge from the resonator.
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: See "Posh Box" being built for "nudiefish"
« Reply #12 on: May 28, 2013, 07:30:36 AM »

Excellent stuff - great to see the foam reedblocks in parts - it`ll be very interesting to see them when they`re complete and also with reeds waxed in .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

nudiefish

  • Member
  • *
  • Offline Offline
  • Posts: 40
  • Aussie Morriser
    • Art Prints
Re: See "Posh Box" being built for "nudiefish"
« Reply #13 on: May 28, 2013, 08:55:56 PM »

The bloke hopping impatiently from one leg t'other waiting for this darned box is me,  Peter!  Thanks for all the updates, Mate. I know that you are talking a lot of trouble in documenting the process.  I'm more than a bit curious on how it all comes together.  For instance,  so that's how the slides work??
Logged
1 x Hohner D/G, 1 Sandpiper Stint D/G and a Hyde D/G Box.  I'm also a photo buff!

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #14 on: June 03, 2013, 11:59:41 AM »

The bloke hopping impatiently from one leg t'other waiting for this darned box is me,  Peter!  Thanks for all the updates, Mate. I know that you are talking a lot of trouble in documenting the process.  I'm more than a bit curious on how it all comes together.  For instance,  so that's how the slides work??
I hope it is not because you want the dunny; they are a little hard to find in Europe
Day 9
Now I will explain why I need wide dividers within the reed blocks. As I never make any instrument any wider than 150mm and this includes three rowers and 3 voice two rowers I’m pushing for all the free space I can get, as I do not want the back reed blocks right under the treble mechanism for obvious reasons. If I put a thick divider in the reed block and then put slots in so the reeds can pass each other but still stay within its own cavity, by doing this I can reduce the top width of the reed block by 5mm. This then gives plenty of room between reed blocks for the reeds and valves not to interfere with each other. The slots are cut out with the bench-mounted router, and I should have taken the slots a little deeper as I can take the divider down to 0.5mm with no problem at all.


Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #15 on: June 10, 2013, 12:02:48 PM »

When I glue down the capping on the reed block the shoe goes up against a very ridged surface like as a small table clamped into the vise and under that I place a wedge with the same taper as the reed block that way I get a good surface for the clamps, or the wedge can go on the top of the capping as shown. I use a 1.5 mm reed block shoe; if it is any thicker it starts to flatten the reeds. When fitting reeds to the reed block and they are too short for the cavity then fill the cavity from the top and reduce the cavity size, some makers and repairers use a strip of timber at the bottom of the reed to rise it up the cavity, it works but flattens the reed in the process.
« Last Edit: June 10, 2013, 12:06:02 PM by Peter Stormy Hyde »
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: See "Posh Box" being built for "nudiefish"
« Reply #16 on: June 10, 2013, 01:12:51 PM »

Thanks for sharing all this, Stormy !!! . keep 'em coming, it`s great to have this here as a resource, you`re the only one i know of who makes Foam reedblocks , I think even Strasser used Wooden ones (albeit Balsa if I remember rightly) in their foam laminate cased Steirische
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: See "Posh Box" being built for "nudiefish"
« Reply #17 on: June 11, 2013, 12:02:48 PM »

Thanks for sharing all this, Stormy !!! . keep 'em coming, it`s great to have this here as a resource, you`re the only one i know of who makes Foam reedblocks , I think even Strasser used Wooden ones (albeit Balsa if I remember rightly) in their foam laminate cased Steirische
I’m glad you are getting some use from it.
Intresting about the Strasser that they are now using balsa and foam it is the first I have heard of any other makers using these material. When I started using balsa and foam I copped a fair amount of stick as most people thought I was nuts, just as well there are a few nuts in this world.
Here is a link to an old site where I wrote a little about my work at the time on balsa reed blocks, reading it again after so many years I would have to make a couple of changes!!!

http://www.19larchclose.freeserve.co.uk/acc/Stormy.htm
« Last Edit: June 12, 2013, 12:12:43 AM by Peter Stormy Hyde »
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: See "Posh Box" being built for "nudiefish"
« Reply #18 on: June 11, 2013, 12:40:49 PM »

Intresting about the Strasser that they are now using balsa and foam it is the first I have heard of any other makers using these material.


They aren`t now but they did experiment with them and other unorthadox materials a few years back
Logged
Q: How do you cure MAD?
A: Buy more Boxes

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: See "Posh Box" being built for "nudiefish"
« Reply #19 on: June 12, 2013, 11:13:36 AM »

Very nice and interesting report!
Thank you very much for sharing all this interesting information.

Whre are the pictures about ths building process?

---------------------------------------------------------------------------------------------
I did build an other big box this Year.
It is a GCFB Heliconbox all in massive wood. 19,8cm x 36cm 5,2 kg

https://plus.google.com/photos/116672106411032803534/albums/5874487803623754961?banner=pwa

Best regards, Johann Pascher
Logged
Pages: [1] 2 3 4 5 6   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal