Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Wolfgang on August 05, 2018, 12:34:08 PM
-
Hello everyone!
I've two squeaking bass buttons on my new used Castagnari. It comes from the spot where the little springs rub on the metal levers. I've tried cleaning them thorughly and applying a tiny bit of graphite powder. Worked for two or three weeks, but now the squeak is coming back. Any advice on how to fix that for longer? I thought I should avoid machine oil?
Thanks and greetings,
Wolfgang
-
It's an annoying and frustrating problem which occurs sometimes. You have done the right thing so far, using graphite. It's best to avoid all oil or grease, as this will only attract dust and muck. You could try the following:
1. Add the graphite in a suspension with a little methanol. The methanol will carry the graphite further than just the powder alone and then will evaporate, leaving a film of graphite.
2. You could try just opening up the 'U'-shaped end of the spring by a tiny amount using a small screwdriver blade or similar. This would reduce the area of contact a little and may solve the squeak, especially if graphite is used too.
3. You seem fairly certain that the squeak comes from the point of contact that you've already mentioned, but it could be coming from elsewhere too; sometimes the coils of the spring can cause squeaks and a bit of graphite/methanol suspension can work here too.
-
I use PTFE dry lubricant spray,Spray some into the cap then apply with small paint brush,
Available fro Toolstation.
-
I had the same problem, and used Pete's solution successfully, but the squeak has come back again after a few months. Shouldn't happen on a very expensive new box!
-
Geof
I have sent you an email,I will sort that under warranty
Pete
-
Thanks for the shared wisdom everyone. My box is still under waranty too, but I don't want to ship it.
I'll try maybe the dry PTFE. Can I use the WD-40 brand, they have a dry product as well?
Greets, Wolfgang
-
Very simple fix, use a screwdriver to push the spring away from the rod a little then apply some graphics from a pencil. Works a treat, took me ages to track it down but fixed on many Castagnaris and is easy
-
Thanks for the shared wisdom everyone. My box is still under waranty too, but I don't want to ship it.
I'll try maybe the dry PTFE. Can I use the WD-40 brand, they have a dry product as well?
Greets, Wolfgang
Is it as aromatic?
-
Very simple fix, use a screwdriver to push the spring away from the rod a little then apply some graphics from a pencil. Works a treat, took me ages to track it down but fixed on many Castagnaris and is easy
Thanks, I'll try that first.
-
Is it as aromatic?
I have no idea?!
-
Hi
Something I have done in the past also,if you undo the spring just rub the rod where the spring sits with some fine wet and dry or emery cloth before applying lubricant
-
Sorted using Pete's emery paper + PTFE suggestion. Hope it's a permanent fix this time.
-
Very simple fix, use a screwdriver to push the spring away from the rod a little then apply some graphics from a pencil. Works a treat, took me ages to track it down but fixed on many Castagnaris and is easy
Thanks, I'll try that first.
Done that, let's see how long it keeps the squeak away. If not, I'll try one of the other sugggested fixes. Thanks again, everyone!
-
3. You seem fairly certain that the squeak comes from the point of contact that you've already mentioned, but it could be coming from elsewhere too; sometimes the coils of the spring can cause squeaks and a bit of graphite/methanol suspension can work here too.
I was fairly certain, but it seems I was indeed wrong. No treatment worked out well. Obviously there's a second spot where the spring rubs on the lever (yellow circles). I've tried to bend them away a little and applied some dry lubricant there. Seems that fixed it now, hopefully for a while.
Thanks for all the input! I enjoy my Casta a lot :-)