Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Peadar on January 28, 2019, 09:24:35 PM
-
A bit of advice needed...
1) Thumb-strap: One of my Hohners has what is obviously a replacement thumbstrap, neatly done and fixed with a shiny new rivet but made of artificial leather. The edge of the strap rapidly cut into my thumb. I have removed the strap and put on a soft leather substitute, button holed and slipped over the rivet head, but it keeps coming off....
So how do I remove the rivet to do the job from scratch?
2) Bass strap-The bass strap as fitted to my Hohner 1040 leaves a lot of wriggle room for my left hand this makes it difficult to rapidly switch from bellows push to pull.
Is the standard solution to shorten the strap so it touches the back of my hand?
Answers on a post-card please
-
I just cut off my rivet and fitted a new strap with a bolt and washers and locking nut . Not pretty but works well . Just take the keyboard off and cut rivet from the inside with some sharp nose pliers.
-
A bit of advice needed...
2) Bass strap-The bass strap as fitted to my Hohner 1040 leaves a lot of wriggle room for my left hand this makes it difficult to rapidly switch from bellows push to pull.
Is the standard solution to shorten the strap so it touches the back of my hand?
Could you fit something like this?
http://www.cgmmusical.co.uk/CGM_Musical_Services/Bass_Straps.html#23
-
To adjust the bass strap, just undo the bottom fixing and make new screw holes a short distance away from the existing ones and refit. I emphasis the 'short distance' bit as the effect of the reduction in length is more than you may think.
-
Just to add to Lester's answer - the new screw holes should be made in the leather strap, not in the wooden casework of the box (as I have sometimes come across :'( )
Shifting the screw holes even just 5 mm can make a noticeable difference.
-
Thanks for all the answers...Done the bass strap. Took it in 5mm twice and it feels a lot better- the previous owner obviously had bigger paws than me. Steve's advice was well timed- I renewed a bass strap on a Casali PA last year and found two sets of screw holes under one end...I nearly learnt by example.
Peadar
-
My standard fix is to replace the rivet with a T-nut glued in place from the inside of the keyboard.
https://www.albanycountyfasteners.com/T-Nuts-s/414.htm
You can bend off the prongs so it sits flat inside the keyboard.
-
Back to the Bass Strap...
Replaced the (perished) rubberised canvas bass strap on the Antoria growl box with a leather one... Will need to slacken it off I think. Holds my hand really securely- so securely I can work neither the air valve nor the bass buttons.
Hmm.
-
Aside adjusting the length of the bass strap, you may find that experimenting with different hand positions will help. If you kind of curve your hand like you are cupping a ball it will increase the tension against the strap.
-
If your box is equipped with the usual pair of shoulder straps you don't need a thumb strap.
-
If your box is equipped with the usual pair of shoulder straps you don't need a thumb strap.
No you have pair of shoulder straps don't need a thumb strap but you may chose to use one.
Also you don't need a thumb strap if you only use a single shoulder strap but you may choose to use one.
-
I find myself using different hand positions when playing faster cross row passages than using a thumb strap would allow, but that's just me. I watched a good player the other day who does use a thumb strap, and I noticed that his Castagnari thumb strap was on a one fastener pivot, which allowed a lot better access to the keyboard length then you can get on the hand trapping Hohner ones.
-
If your box is equipped with the usual pair of shoulder straps you don't need a thumb strap.
I am not sure that shoulder straps where common at the time boxes were still being labelled " Made in Saxony". Just a bit reluctant to fix the brackets on the old lady.