Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Telemorris on December 15, 2010, 05:27:16 PM

Title: Bellows repair material
Post by: Telemorris on December 15, 2010, 05:27:16 PM
I just found this fine leather product at Talas.

http://apps.webcreate.com/ecom/catalog/product_specific.cfm?ClientID=15&ProductID=20728

Goldbeater's skin. It's very thin, tough, and might be just the ticket for sealing holes in bellows gaskets. Has anyone ever used this product?

My old Hohner ADG bellows has holes in many of the bellows gaskets and this seems like the right kind of product to do the repairs without adding bulk.

Title: Re: Bellows repair material
Post by: Christopher K. on December 15, 2010, 05:40:48 PM
Why not just replace the gaskets with gasket tape? Unless it's something else you mean by gaskets?
Title: Re: Bellows repair material
Post by: Telemorris on December 15, 2010, 05:53:40 PM
Hmm, sounds like I have my nomenclature wrong again.

What I want to do is repair holes in the leather corner diamonds on the bellows. For some reason I keep thinking of them as gaskets. Sorry.

Bellows gaskets are the strips of material that are used to seal the joint between the bellows frames and the treble and bass ends.



Title: Re: Bellows repair material
Post by: Steve_freereeder on December 15, 2010, 07:15:55 PM
What I want to do is repair holes in the leather corner diamonds on the bellows. For some reason I keep thinking of them as gaskets. Sorry.
Charlie Marshall's your man.....
Leather bellows corners (http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#12).
Title: Re: Bellows repair material
Post by: HallelujahAl on December 15, 2010, 07:25:14 PM
Quote
Charlie Marshall's your man.....
Leather bellows corners.
AY! He's the fella - though I've used the stuff from talas - ve. similar to the same super-thin plain leather that David Leese also sells on his concertina-spares wbsite.
AL
Title: Re: Bellows repair material
Post by: Christopher K. on December 16, 2010, 01:42:41 AM
Quote
Charlie Marshall's your man.....
Leather bellows corners.
AY! He's the fella - though I've used the stuff from talas - ve. similar to the same super-thin plain leather that David Leese also sells on his concertina-spares wbsite.
AL

Am I correct in assuming these are for patching the corners of the bellows from within? What type of glue is best?

 
Title: Re: Bellows repair material
Post by: Telemorris on December 16, 2010, 06:12:15 AM
Some of the diamonds in my bellows have small holes that need to be repaired. I'm wondering if it's better to completely replace the diamond or patch the hole? I was thinking of using the material from Talas as a patch material since it is extremely thin and shouldn't create a bulky repair.
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 08:27:20 AM
In my humble opinion the presence of more than one or possibly two damaged gussets is grounds for fitting new bellows.  Patching from inside is the simplest to do, but the patching material should be thin (less than .5mm) and it must also be airtight, not all leathers are.
Title: Re: Bellows repair material
Post by: malcolmbebb on December 16, 2010, 12:42:06 PM
I'm looking at repairing a bellows on a rather more hexagonal free reed instrument, which has several leaking corners and really doesn't warrant new bellows (financially).

I'm trying to decide between some 0.2mm leather from David Leese or some of Charlie's zephyr stuff. Any suggestions or better ideas - or should I just ask on t'other forum?

Somebody has tried external repairs in the past and they're 'orrible. And leaky.
Title: Re: Bellows repair material
Post by: Lester on December 16, 2010, 12:58:42 PM
I'm looking at repairing a bellows on a rather more hexagonal free reed instrument, which has several leaking corners and really doesn't warrant new bellows (financially).

I'm trying to decide between some 0.2mm leather from David Leese or some of Charlie's zephyr stuff. Any suggestions or better ideas - or should I just ask on t'other forum?

Somebody has tried external repairs in the past and they're 'orrible. And leaky.

HalelujahAl is our resident concertina bellows expert so if he does not see this you may like to pm him.
Title: Re: Bellows repair material
Post by: Broadland Boy on December 16, 2010, 01:34:15 PM
I just found this fine leather product at Talas.

Goldbeater's skin. It's very thin, tough, and might be just the ticket for sealing holes in bellows gaskets. Has anyone ever used this product?


Don't know about its use on bellows but having just read a book on the development of the Zeppelin, this is what they made the gas bags from, which (mostly) kept the hydrogen in.

Richard
Title: Re: Bellows repair material
Post by: HallelujahAl on December 16, 2010, 01:57:03 PM
Quote
I'm looking at repairing a bellows on a rather more hexagonal free reed instrument, which has several leaking corners and really doesn't warrant new bellows (financially).

I'm trying to decide between some 0.2mm leather from David Leese or some of Charlie's zephyr stuff. Any suggestions or better ideas - or should I just ask on t'other forum?

Somebody has tried external repairs in the past and they're 'orrible. And leaky
.
Sounds like they just need a re-bind - as long as the leaks are only on the corners. Wouldn't bother with either Dave's or Charlie's Zephyr (tis the same material essentially). Would ensure that the leaks are simply on the corners by taking one end off and removing reed pan and shine a torch inside or sticking a shing lightbulb inside it, marking with chalk the places where it's leaking from. Then purchase a run of leather from Dave Leese (usually 3/4" black skived both on both edges on one side) and glue the bind around after end-skiving etc. I use a number of different leather glues - but Tandy's 'Leather Weld' is a good product, don't even think about trying to use pva as it is not flexible and will fail. That'll last you a few years. You can also tidy it up by then sticking on some new bellows papers if you want. For a nice finish obviously it makes sense to do all the bellows folds, and make sure you start and finish the skived ends on what is for you the 'bottom' set of bellows folds. PM me if you want more detail/info. And if you can't be bothered then feel free to send the bellows to me and I'll do a rebind for you as long as you buy the leather and make a donation to The Salvation Army  ;D
Regards, AL
Title: Re: Bellows repair material
Post by: Telemorris on December 16, 2010, 07:33:16 PM
In my humble opinion the presence of more than one or possibly two damaged gussets is grounds for fitting new bellows.  Patching from inside is the simplest to do, but the patching material should be thin (less than .5mm) and it must also be airtight, not all leathers are.


I need to patch for the time being. I have some chamois and can take the thinnest portion of the hide for patching, if you think that will work. The Presswood only needs one patch though I will need to make new bellows for the ADG when I get to fixing it up.
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 11:09:17 PM
Chamois is no good for gussets,  much too porous. 
Title: Re: Bellows repair material
Post by: malcolmbebb on December 16, 2010, 11:22:52 PM
Quote
Sounds like they just need a re-bind - as long as the leaks are only on the corners.

Sorry, they are on the inside (bottom) corners - the easy ones have been re-taped! The leather seems very dry at these points.
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 11:28:58 PM
Are we  talking about concertina or melodeon bellows here?
Title: Re: Bellows repair material
Post by: malcolmbebb on December 16, 2010, 11:37:57 PM
In this instance, Concertina.
I was wondering about moving the topic to CNET but it seems to overlap pretty well with melodeon questions - unless there'a a fundamental difference other than size?
Title: Re: Bellows repair material
Post by: Telemorris on December 16, 2010, 11:40:04 PM
I am talking about melodeon gussets.
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 11:42:41 PM
In this instance, Concertina.
I was wondering about moving the topic to CNET but it seems to overlap pretty well with melodeon questions - unless there'a a fundamental difference other than size?

There are considerable differences, and its quite confusing for me (I don't know about others) to have the two topics mixed up like this.
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 11:46:36 PM
I am talking about melodeon gussets.

Right

Well chamois is still too porous!  In general either cow, calf or goat leathers are sufficiently airtight, but you still need to find something that is sufficiently thin and flexible.  Some clothing leathers are suitable,  glove leather is particularly good, but you won't get many gusset sized pieces free of stitching out of a pair of gloves.  The binding leather sold by David Leese would be good.
Title: Re: Bellows repair material
Post by: malcolmbebb on December 16, 2010, 11:47:29 PM
In this instance, Concertina.
I was wondering about moving the topic to CNET but it seems to overlap pretty well with melodeon questions - unless there'a a fundamental difference other than size?

There are considerable differences, and its quite confusing for me (I don't know about others) to have the two topics mixed up like this.
Fair point. I'd already gone to PM so the last post was just a clarification anyway. I'll shut up now.  :-[
Title: Re: Bellows repair material
Post by: Theo on December 16, 2010, 11:52:21 PM
In this instance, Concertina.
I was wondering about moving the topic to CNET

Good idea  (:)
Then you won't have to:
Quote
shut up now.  :-[
Title: Re: Bellows repair material
Post by: Telemorris on December 17, 2010, 05:44:29 AM
In general either cow, calf or goat leathers are sufficiently airtight, but you still need to find something that is sufficiently thin and flexible.  Some clothing leathers are suitable,  glove leather is particularly good, but you won't get many gusset sized pieces free of stitching out of a pair of gloves.  The binding leather sold by David Leese would be good.

Does the leather used for patching a gusset on a melodeon need to be thinner than the leather used to make the gusset in a new bellows? I've read in the archives that leather for patching melodeon gussets needs to be about .5 mm or so. How thick is the leather for gussets supplied by Charlie? The binding leather sold by David Leese is listed as .2mm thick

I'm asking because I've found some leather that is goat skin between 1 and 1-1/2 oz, or .4 to .6 mm thick. Would that do for both gussets and patching gussets? Is it too thick for gussets on a new bellows?
Title: Re: Bellows repair material
Post by: HallelujahAl on December 17, 2010, 07:30:17 AM
Quote
Is it too thick for gussets on a new bellows?
imho the answer is yes!
Title: Re: Bellows repair material
Post by: Telemorris on December 18, 2010, 01:49:31 AM
I'm going to call my local pipe organ repair shop to see what scraps of leather they have. What is the proper thickness for new bellows gussets?
Title: Re: Bellows repair material
Post by: george garside on December 18, 2010, 10:59:58 AM
I use "ladies glove leather"  for internal bellows repairs& have had no problems with it being thin, flexible & airtight..  The good thing is that it can be had for free!  Ladies semm to lose gloves one at a time rather than in pairs so a bit of asking around can yield  a supply of 'odd' gloves.

george
Title: Re: Bellows repair material
Post by: HallelujahAl on December 18, 2010, 01:30:28 PM
Charlie Marshall's leather gusset material is perfectly fine - I've used his stock on both concertinas, melodeons and accordions. I skive them down a little myself anyway - but they're great and I can recommend them (and Charlie, who is one hell of a good imho!).
AL
Title: Re: Bellows repair material
Post by: Broadland Boy on December 18, 2010, 09:13:38 PM
I'm going to call my local pipe organ repair shop to see what scraps of leather they have. What is the proper thickness for new bellows gussets?


I think they will know this as 'Zephyr', used mainly on the air motors operating keys etc., if that helps Telemorris

Richard
SimplePortal 2.3.5 © 2008-2012, SimplePortal