Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Theo on March 11, 2011, 10:58:44 PM
-
I need some help with an electronics project. I have a Tandy PZM that I want to fit to the left end of my box. It comes with a battery power supply and a mini jack connector. I would really prefer to be able to run it from phantom power, but I understand that this will require either modification or replacement of the electronics in the power supply. While I'm at it I'll replace the jack with an xlr connector.
Problem is my knowledge of electronics is pretty much non-existant. Can anyone suggest how to proceed, or even offer to do the job for me?
-
You may have already seen it, but, if not, there's a bit about phantom powering Tandy PZM in this Sound on Sound microphone article (http://www.soundonsound.com/sos/aug99/articles/micfaq.htm) (half way down, yellow box).
-
Theo,
There are various ways of making an electret mic phantom powered from the cheap and nasty to the opposite end of the scale. Adding a couple of resistors and a capacitor can work but values are dependent on the particular electret and this doesn't provide a balanced ouput. I wouldn't recommend this route.
I have in the past modified a simple active DI box to provide the power for the mic. The DI box deals with provision of relatively low voltage for its own electronics and provides the balaced output signal. Just requires a couple of components to add the supply to the input.
Orchid electronics do a mini DI that I've used for this http://www.orchid-electronics.co.uk/micro.htm (http://www.orchid-electronics.co.uk/micro.htm)
Alternatively they also do a box made for this http://www.orchid-electronics.co.uk/contact_mic.htm (http://www.orchid-electronics.co.uk/contact_mic.htm)
I've also used a phantom power adapter in an extended XLR plug which you can get from AKG (expensive) or similar. Maplin used to do a £20 electret mic with such a device attached but I can't see them on their web site now. I may have a spare one! I'll get back to you on that.
Howard
-
Hi Theo....we use an electronics engineer up in Inverness by the name of Roger Tingle (some name for a sparky)...very good and helpful chappie...anyhows...will contact you direct with his number...TomC
-
Maplin used to do a £20 electret mic with such a device attached but I can't see them on their web site now. I may have a spare one! I'll get back to you on that.
Howard
I have a spare used phantom power adapter from a maplin microphone. It has a small mic transformer inside with a few components to derive the electret supply from the phantom. Not as complex as the AKG variety. I've attached a quick photo by holding it in front of the web cam.
Alternatively, have a look at http://www.epanorama.net/circuits/microphone_powering.html#phantom (http://www.epanorama.net/circuits/microphone_powering.html#phantom)
Howard
-
I have a spare used phantom power adapter from a maplin microphone. It has a small mic transformer inside with a few components to derive the electret supply from the phantom. Not as complex as the AKG variety. I've attached a quick photo by holding it in front of the web cam.
I think I might have one of those myself. Can I just connect the electret capsule from the pzm in place of the original?
Alternatively, have a look at http://www.epanorama.net/circuits/microphone_powering.html#phantom (http://www.epanorama.net/circuits/microphone_powering.html#phantom)
Howard
I can sort of understand about half of that!
-
[I think I might have one of those myself. Can I just connect the electret capsule from the pzm in place of the original?
Yes, the solder pads are pretty small but I've done this with other types of electret mics. Make sure to get it the right way round. You might like to attach a short lead with a 3.5mm in-line jack socket to the phantom adapter and then just plug the mic in. That way you can use it with the original battery box as well.
Howard
-
I could do this for you.
I have made several battery boxes for Microvox kit, all of which use an XLR for output to an ordinary mic cable. The one I use regularly for band work actually combines the output from a Microvox mic for the bass end with an SM57 for the treble end.
Mine use batteries, and will tolerate phantom power but don't actually use it, but I know how to do it using the phantom power instead of batteries.
What size is the mini jack?