Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Owen Woods on February 17, 2012, 03:54:33 AM

Title: Reed Block Acoustics
Post by: Owen Woods on February 17, 2012, 03:54:33 AM
So I've been learning a few bits and pieces about box acoustics over the last few months. Today I finally got round to reading some stuff which had been sitting in my favourites for months after someone linked it to me on this forum. They are a few papers on box acoustics, especially on reed blocks.

First is a paper on resonance in chambers by Tom Tonon (of pitch bending accordion fame). Here it is: http://www.concertina.org/pica/pica_2005_2/html/reed_cavity_design_resonance.htm (http://www.concertina.org/pica/pica_2005_2/html/reed_cavity_design_resonance.htm). The main conclusion of it is, as far as I see it, that Helmholtz resonance of the chamber is a Bad Thing, but that quarter wave or full wave could boost volume of the reed and amplify certain harmonics, if a full or partial partition was placed in the chamber. This is interesting, but if you look at the table at the bottom it becomes clear that both quarter wave and full wave resonance is exponential (as expected), meaning that it's application to reed blocks in it's simplest form is impractical. One could "tune" blocks to exhibit quarter or full wave resonance at different partials, meaning that every chamber would cause some kind of resonance, but since different partials would be excited for every reed it is quite likely that the resulting sound would be haphazard and disjointed.

It would however be interesting to see if (say) a single octave instrument could be constructed with a block large enough at the low end and small enough at the top end to consistently excite the quarter wave resonance. I think it would be possible, but you'd have to tabulate all of the lengths so as to match to plates as closely as possible. And of course there would be little practical application.

The conclusions are backed up by this paper, which concludes that "For a given reed, general characteristics of the spectrum seem independent of cell [i.e. chamber] length" (http://www.public.coe.edu/~jcotting/acoustics.html (http://www.public.coe.edu/~jcotting/acoustics.html)). However it does note that increasing the chamber length can amplify the 1k-3k frequencies, which is potentially useful. However, since doubling the length of the reed chamber results in an increase in response of around 1.5 times, the effect isn't hugely significant over the range of practical chamber sizes. What is more interesting is that the presence of a chamber does change the sound of a reed, no matter what the size of the chamber is. This sounds similar to putting a loudspeaker in a baffle, which radically and immediately changes the sound. In fact the bellows act as a baffle - the sound of a reed inside the bellows is very different from the sound of a reed mounted outside the bellows [That might be wrong, this is based on a lecture that I was mostly asleep in].

So it appears that the function of reed block tapering is purely to ensure that there is enough air going into the reed so that it doesn't choke. Resonance is likely to be a bad thing, either because it interferes with the reed (which is bad) or because it results in uneven amplification and timbre across the instrument. Changing the dimensions of a chamber will affect the sound of the reed, but in a fairly negligible way.

What about mounting? Flat mounted reeds produce a very different sound from block mounted reeds. Part of this is due to a different transient response (i.e. attack), but there is more to it I think. I can think of two different mechanisms. One is that by distributing the force on the reed in a different way, the motion of the reed changes somehow and affects the sound. As the dominant frequency in the reed's vibration is the fundamental and the sound is based on pressure fluctuations caused by the reed blocking off and unblocking off the air supply, I'm doubtful of how much this would change the sound, especially since most traces I've seen show the movement of the reed as pretty much sinosoidal. Although modes of vibration of the reed do appear in the spectrum when excited by air (http://www.public.coe.edu/~jcotting/ICA2007%20Free%20Reed.pdf (http://www.public.coe.edu/~jcotting/ICA2007%20Free%20Reed.pdf), it seems unlikely that they would necessarily translate into sound. The other explanation is that by altering the air intake the flow pattern changes, meaning that the air coming out of the reed has a different direction and velocity. Again though, the frequency is dependent on the period of blocking and unblocking - what effect would different flow actually have?

My problem now is that I have lost sight of how reeds differ, except by their fundamental mode of vibration. Nobody that I can find has ever studied different kinds of reed for the same instrument of the same pitch. So if the sound of boxes is independent of soundboard and is independent of reedblock, what makes good reeds sound good and bad reeds sound bad?

That might be unintelligible, but it is nearly 4am and I have a project meeting about stringed instrument acoustics in 5 hours.
Title: Re: Reed Block Acoustics
Post by: Theo on February 17, 2012, 09:07:32 AM
So if the sound of boxes is independent of soundboard and is independent of reedblock, what makes good reeds sound good and bad reeds sound bad?

This statement does not follow from your previous discussions, its false logic.  Your arguments clearly describe why some possible effects on sound production are not going to happen, but there may be others.   One could test the statement of yours that I have quoted with some fairly straightforward experiments in a test rig that simulates a real instrument but where reedblocks and/or soundboards of different designs and materials can be substituted. 

My own personal hunch is that the materials and construction of reedblocks is critical, but I'm afraid I don't understand the factors involved well enough to design the ideal reedblock.  One small clue is in the design of the Castagnari Mory.  I'm not alone in believing that the models made prior to the late 1990s are superior players to the ones made around 2000 and onwards (though recent examples are better).  The early Mory (identifiable by the semicircle design on the grill) have reedblocks carved out of a single piece of timber with the grain running lengthwise, with a cap and base glued on.   Later ones are built up from a mid rib with chamber walls glued on.   The most highly regarded Paolo Sopranis also have their blocks made in the same manner as the early Mory. I don't know what this means, but there could be something there.   What I suspect is important is the ability of the reedblock to hold the reed rigidly and to resist any vibration of the reed plate, thus ensuring that as much energy as possible is retained in the vibrating reed.

I have one other hunch, nothing stronger than that, about the difference in sound from a flat mounted reed as opposed to one on a block is, at lease in part, simply a result of the site where the sound is produced is closer to the outside world, therefore the emerging sound has a shorter path with less opportunity for being modified by interaction with the surfaces it passes.

Title: Re: Reed Block Acoustics
Post by: pete /acorn on February 17, 2012, 10:36:45 AM
Hi,
I think Theo is correct,I've been doing a lot of looking and comparing recently but more with piano accordions,the reed block material effects the sounds greatly,also with piano boxes a lot of the well respected older makes use leather under the reeds and pin the reeds on.
I think with the reed  flat onto the soundboard,as Theo said makes the sound sharper.A good example of how sounds change,get hold of a cassotto box,especially one with a cedar cassotto chamber,the resonance makes the bassoon reed in a PA sound richer very like a Bassoon and if the clarinet reed is in the cassotto chamber this then produces a sound more akin to a wooden clarinet,obviously the resonance of the chamber has a great influence on the sound of the instrument.

Pete

Title: Re: Reed Block Acoustics
Post by: Theo on February 17, 2012, 11:06:29 AM
A good example of how sounds change,get hold of a cassotto box,especially one with a cedar cassotto chamber,the resonance makes the bassoon reed in a PA sound richer very like a Bassoon and if the clarinet reed is in the cassotto chamber this then produces a sound more akin to a wooden clarinet,obviously the resonance of the chamber has a great influence on the sound of the instrument.


I fully agree that the cassotto chamber makes a difference to the sound, but I don't think it is correct to describe it as being produced by "resonance of the chamber".  Ukebert has given a good summary of why resonance is almost certainly not a beneficial thing in reed block acoustics.  What does happen in the longer and larger chamber such as a cassotto is that there is a more complex pattern of reflection of sound waves within the chamber which can cause a variety of interactions between partials, and a much greater opportunity for absorption of sound by the chamber walls.    I strongly suspect that it is this increased internal reflection of sound that is responsible for the different sound character.
Title: Re: Reed Block Acoustics
Post by: mory on February 17, 2012, 11:23:36 AM
Theo Quote [I have one other hunch, nothing stronger than that, about the difference in sound from a flat mounted reed as opposed to one on a block is, at lease in part, simply a result of the site where the sound is produced is closer to the outside world, therefore the emerging sound has a shorter path with less opportunity for being modified by interaction with the surfaces it passes.]

When I place a reed flat on my tuning bellows either on a flat/half block or straight on the surface they are always much louder than any on upright blocks, I always thought of it as the angle of attack if you like with the air coming from behind the tongue on the flat mounted and end on on the upright racks, maybe to do with turbulence I suspect, same loud volume in a Connie for same reason regardless of other contributary factors AtB mory

same happens with a mouthie comb
Title: Re: Reed Block Acoustics
Post by: Theo on February 17, 2012, 11:54:47 AM
Good points Mory.

As a scientist by training I know it is important to distinguish between things we can actually observe and the separate step of explaining why the differences are there.  For example we can easily observe that flat mounted reeds sound different from reeds on an upright block, but explaining why is a much more complex business. Between us we have  come up with some ideas of what we guess might be going on, now we need someone like ukebert to do some investigation and careful experiments to try to get a working theory that we can use to predict which design factors determine the kind of sound we want.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 17, 2012, 12:23:56 PM
It is a mind numbing but fascinating thing.  There are quite a few variables other than just the reed block that also come into play.  Sound hole size, chambers varnished or not, bellows size, and of course the reeds themselves and how they're set up.  I've wondered how much the taper matters.  And maybe you can explain why blocks are tapered larger at the bottom of the reed to smaller at the top.  And, I wonder, what is optimum taper?  I use 2 1/2 degrees, not for any particular reason, I just ended up there.  Seems every bit of testing I do is contradictory.

Randy Falcon has done some testing of different size/shape reeds of same pitch and has some definite opinions on which he prefers, but like Theo pointed out, explaining why is another matter.  And deciding which one you like best can be completely nullified by not being able to buy them in that configuration.

I was convinced reed block material made a big difference in the sound(and still hold on to that some), even though a highly respected builder told me it didn't, until I made one with balsa blocks, which has just as rich and loud a sound as the ones I make out of hard maple.  I did make some with a wood harder than hard maple, and I didn't like the sound. It seemed more shrill and less rich.

I really think accordions laugh at people trying to apply human logic to them.  They're baffling creatures.
Title: Re: Reed Block Acoustics
Post by: mory on February 17, 2012, 01:09:59 PM
I think the tapered block (bottom to top) is an exercise in getting the air flow behind the tongue as in the flat mounted reed and is a real necessity in an upright block to get a quick response to the reed even if it lacks a little in volume by comparison AtB mory
Title: Re: Reed Block Acoustics
Post by: pgroff on February 17, 2012, 02:28:44 PM
I think the tapered block (bottom to top) is an exercise in getting the air flow behind the tongue as in the flat mounted reed and is a real necessity in an upright block to get a quick response to the reed even if it lacks a little in volume by comparison AtB mory

This is something I was also considering, after our recent discussion of the Baldoni and V. Soprani reedblocks shown here:

http://forum.melodeon.net/index.php/topic,8225.msg109766.html#new

PG
Title: Re: Reed Block Acoustics
Post by: diatonix on February 17, 2012, 02:42:17 PM
As a builder I do not worry too much about what to make my reed blocks from. My personal choice is alder: it works easily, it is stable, resistent and not too heavy, glues well. It is also relatively inexpensive. I also used abachi in two or three batches, but continuous exposure to its dust may lead to health issues...
My priorities: Sound improves noticeably when the blocks are glued straight on the board (no bottom, no gasket, no screws). Large sound holes. Following this simple recipe you should get more or less the same result as with flat mounted reeds.
Title: Re: Reed Block Acoustics
Post by: pgroff on February 17, 2012, 06:14:31 PM
As a builder I do not worry too much about what to make my reed blocks from. My personal choice is alder: it works easily, it is stable, resistent and not too heavy, glues well. It is also relatively inexpensive. I also used abachi in two or three batches, but continuous exposure to its dust may lead to health issues...
My priorities: Sound improves noticeably when the blocks are glued straight on the board (no bottom, no gasket, no screws). Large sound holes. Following this simple recipe you should get more or less the same result as with flat mounted reeds.

I know some electric guitar enthusiasts who claim to hear a difference between alder and ash for solid-body instruments (and prefer alder).  

Regarding the second point, you can sometimes hear the difference cited by diatonix in the same instrument -- that is, in accordions and concertinas that have one or more reedblock glued to the soundboard, and another one or more reedblock removable, with gasket and screws.  As an example, in the photo below, the box on the left has two removable reedblocks and the notes from the inside row are a little more muffled than from the outside row of buttons, probably due to the position of pallets down close to the keyboard.  The box in the middle has the same arrangement of pallets, but the notes from the inside row seem brighter than from the outside row -- probably because the reedblock for the reeds sounded from the inside row of buttons is glued in place with no gasket.  Some modern german-made 20 key concertinas* also have a mixture of glued-in and removable reedblocks and the same phenomenon can be noted.

PG

*for example, the model for sale at the top of this list:


http://www.elderly.com/vintage/cats/160U.htm



Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 18, 2012, 01:09:02 AM
This statement does not follow from your previous discussions, its false logic.  Your arguments clearly describe why some possible effects on sound production are not going to happen, but there may be others.   One could test the statement of yours that I have quoted with some fairly straightforward experiments in a test rig that simulates a real instrument but where reedblocks and/or soundboards of different designs and materials can be substituted.

You are of course, quite right! My statement was a rather unscientific piece of frustrated rhetoric. My problem is that I feel that many of the more conventional (in musical instrument acoustics terms) ways of defining the sound have been disproved and I can't think of adequate mechanisms to explain the rest.

Quote
My own personal hunch is that the materials and construction of reedblocks is critical, but I'm afraid I don't understand the factors involved well enough to design the ideal reedblock.  One small clue is in the design of the Castagnari Mory.  I'm not alone in believing that the models made prior to the late 1990s are superior players to the ones made around 2000 and onwards (though recent examples are better).  The early Mory (identifiable by the semicircle design on the grill) have reedblocks carved out of a single piece of timber with the grain running lengthwise, with a cap and base glued on.   Later ones are built up from a mid rib with chamber walls glued on.   The most highly regarded Paolo Sopranis also have their blocks made in the same manner as the early Mory. I don't know what this means, but there could be something there.   What I suspect is important is the ability of the reedblock to hold the reed rigidly and to resist any vibration of the reed plate, thus ensuring that as much energy as possible is retained in the vibrating reed.

I don't think that the material of the reedblock makes much difference, but I think that the construction of the reedblock may well have an effect. Certainly, as you say, the vibration of the reedplate (or rather the lack of it) is very important, as is the lack of vibration of the block. As for multiple pieces, I'm not sure how that would affect the vibration of the block - probably decrease some modes and increase others, so it might well be that the construction that you state gives a more rigid block. With some thought a multiple piece reedblock could possibly be designed such that vibration was selected against, as the glue join probably would constitute a block to vibration. Talking out of my hat here you will have guessed, it's a complex shape and I've got little experience with how it would behave. The material might have some effect in how the block vibrates, but I think that the construction dominates.

Quote
I have one other hunch, nothing stronger than that, about the difference in sound from a flat mounted reed as opposed to one on a block is, at lease in part, simply a result of the site where the sound is produced is closer to the outside world, therefore the emerging sound has a shorter path with less opportunity for being modified by interaction with the surfaces it passes.

I think that this is probably true. But I don't think that it's the whole story. I think that the difference is about air flow and I think (at the moment) that it is air flow that makes a reed good or bad. The fundamental is dependent on reed geometry, but my hunch is that the shape of the resultant waveform and perhaps more importantly the way that the reed behaves as it is being excited is dependent on the flow out of the block, which would primarily be based on the reed shape and the path of the air.

I fully agree that the cassotto chamber makes a difference to the sound, but I don't think it is correct to describe it as being produced by "resonance of the chamber".  Ukebert has given a good summary of why resonance is almost certainly not a beneficial thing in reed block acoustics.  What does happen in the longer and larger chamber such as a cassotto is that there is a more complex pattern of reflection of sound waves within the chamber which can cause a variety of interactions between partials, and a much greater opportunity for absorption of sound by the chamber walls.    I strongly suspect that it is this increased internal reflection of sound that is responsible for the different sound character.

This is possible, but I dunno... I do think that the finish of a reedblock makes a difference, but something doesn't seem quite right, that mechanism doesn't quite sit right with what's in my head. I suppose because I'm still getting my head around the radically different form of sound generation that a reed affords. I think that it's more helpful to think about flow than sound, i.e. a cassotto makes a different sound because the flow does a dogleg. Ready to be called out on that though.

When I place a reed flat on my tuning bellows either on a flat/half block or straight on the surface they are always much louder than any on upright blocks, I always thought of it as the angle of attack if you like with the air coming from behind the tongue on the flat mounted and end on on the upright racks, maybe to do with turbulence I suspect, same loud volume in a Connie for same reason regardless of other contributary factors AtB mory

I think that this is probably the right answer (see above about air flow). What would be interesting would be to see how much of the difference in sound is transient and how much isn't. This could be quite simple, given enough time to set up a repeatable experiment. i.e. set up a air chamber with a compressed air supply and release a valve which triggers a microphone to start recording (preferably in an anechoic chamber) and which will allow air to pass through the reed. The microphone will record the sound coming out until it stabilises (i.e. after a pre-defined period of time) at which point the flow would be swiftly ramped down and once the reed has stopped vibrating the microphone would be turned off. Put the resulting data through a FFT and you could get a sonogram, which would show how the frequency spectrum and amplitude changes over time. The trick would be comparing it to a block, but identical chamber dimensions with reeds from the same manufacturer but the only difference being the location of the hole... yes, I'd say that it would be possible. And that would give you a direct comparison, albeit only for one note and you'd have to design the chamber well such that you wouldn't have any problems with resonance.

I think the tapered block (bottom to top) is an exercise in getting the air flow behind the tongue as in the flat mounted reed and is a real necessity in an upright block to get a quick response to the reed even if it lacks a little in volume by comparison AtB mory

I think that this is an excellent explanation. It would not surprise me in the slightest if this is the reason and the explanation would make it much easier to design good blocks.

As a builder I do not worry too much about what to make my reed blocks from. My personal choice is alder: it works easily, it is stable, resistent and not too heavy, glues well. It is also relatively inexpensive. I also used abachi in two or three batches, but continuous exposure to its dust may lead to health issues...
My priorities: Sound improves noticeably when the blocks are glued straight on the board (no bottom, no gasket, no screws). Large sound holes. Following this simple recipe you should get more or less the same result as with flat mounted reeds.

That observation doesn't surprise me actually and probably the difference between mounting on blocks and flat is partly due to the reedblocks being properly secured. The securing method for reedblocks is pretty suboptimal and if it wasn't for ease of tuning I would think that every block would be glued on, it makes much more sense from a vibration point of view. There will be give in the gasket, which means that there are a whole selection of block modes that just wouldn't be available if they were glued down. Even if they were glued down though there would potentially be more modes available for the blocks than there would be for the pan. The experiment that I detail above wouldn't be affected by that, since both block and pan would only hold one reed and would be clamped, so if that would not yield any data then the clamps would be a potential explanation.

What is frustrating is that I know exactly where in my department there is a lab where such an experiment could be carried out. There is an anechoic chamber and everything. I even know that there is a rig that could be adapted for this purpose. I know all this because it's the basis of the fourth year project of a close friend of mine. For this reason though it is impractical to do anything, as the rig is most definitely in use and will be for the foreseeable future! Plus of course I'm busy enough with my own project (on stringed instrument acoustics, which are a lot more straightforward). Would be an interesting thing to do though and it wouldn't be completely impractical to do it as an amateur, although you'd have to be very careful with noise interference when measuring the sound output from the reed - particularly if you are using a compressor. And you'd need a copy of MATLAB, which is a bit pricey.  
Title: Re: Reed Block Acoustics
Post by: Anahata on February 18, 2012, 08:43:03 AM
You may be on to something with the mention of starting transients. It's well known that much of the recognisable character of the sound of a musical instrument is in the way the notes start. Snip those off recordings of a flute and a trumpet playing the same note, for example, and they sound surprisingly similar. The speed of starting also affects the feel of the instrument for the player, and is a major difference between good reeds and bad reeds.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 18, 2012, 01:01:03 PM
I do not strongly doubt the argument that it doesn't too much matter the material of the block, and my recent balsa block project helps confirm that, but if so, why does it make such a drastic difference if the reed is on an aluminum or brass base?  Why shouldn't the material that the plate is attached to also make a difference?  I also think there is a distinction between what make no difference and what can make a little difference. A little difference can be the difference between preferring this accordion or that one.

With my last 2 projects, I also helped confirm Diatonix's report that a bigger sound hole is better, which also kills what I had previously thought.  I assumed that a hole needed to be big enough, but too big would use too much air.  So I made square holes, which added quite a bit more surface area than my round holes.  I can tell no difference in air consumption, but a noticeable difference in volume and richness of sound. Still can't help but think there is a point of diminishing returns.

Back to blocks. Also as an experiment, I made my blocks on another accordion (with my conventional maple blocks) with dual level chambers.  The thought was since the push/pull reeds are set the space of the plate apart, I would try to take up that space under the push reed. First impression was inconsistent.  Some reeds seemed louder, and some choked.  So I tried shaving down the top of the raised portion under the tip of the push reed, problem solved.  My next 3 will also have these stepped chambers, so hopefully I'll be able to see if it is consistently better than what I had been doing.

My experiments have very little scientific thought, but a whole lot of "what if..",but is definitely the fun part for me.
Title: Re: Reed Block Acoustics
Post by: Theo on February 18, 2012, 01:04:38 PM
IBack to blocks. Also as an experiment, I made my blocks on another accordion (with my conventional maple blocks) with dual level chambers.  The thought was since the push/pull reeds are set the space of the plate apart, I would try to take up that space under the push reed. First impression was inconsistent.  Some reeds seemed louder, and some choked.  So I tried shaving down the top of the raised portion under the tip of the push reed, problem solved.  My next 3 will also have these stepped chambers, so hopefully I'll be able to see if it is consistently better than what I had been doing.

You are in good company there.  Castagnari have made their reed blocks like that for many years.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 18, 2012, 01:26:04 PM

You are in good company there.  Castagnari have made their reed blocks like that for many years.

Ha, I assume that everything I try has probably already been tried.  Do they mill theirs out or do they glue in strips for the step up?
Title: Re: Reed Block Acoustics
Post by: Theo on February 18, 2012, 01:50:22 PM
They are milled.
Title: Re: Reed Block Acoustics
Post by: IanD on February 18, 2012, 02:09:23 PM
I do not strongly doubt the argument that it doesn't too much matter the material of the block, and my recent balsa block project helps confirm that, but if so, why does it make such a drastic difference if the reed is on an aluminum or brass base?  Why shouldn't the material that the plate is attached to also make a difference?  I also think there is a distinction between what make no difference and what can make a little difference. A little difference can be the difference between preferring this accordion or that one.

With my last 2 projects, I also helped confirm Digitonix's report that a bigger sound hole is better, which also kills what I had previously thought.  I assumed that a hole needed to be big enough, but too big would use too much air.  So I made square holes, which added quite a bit more surface area than my round holes.  I can tell no difference in air consumption, but a noticeable difference in volume and richness of sound. Still can't help but think there is a point of diminishing returns.

Back to blocks. Also as an experiment, I made my blocks on another accordion (with my conventional maple blocks) with dual level chambers.  The thought was since the push/pull reeds are set the space of the plate apart, I would try to take up that space under the push reed. First impression was inconsistent.  Some reeds seemed louder, and some choked.  So I tried shaving down the top of the raised portion under the tip of the push reed, problem solved.  My next 3 will also have these stepped chambers, so hopefully I'll be able to see if it is consistently better than what I had been doing.

My experiments have very little scientific thought, but a whole lot of "what if..",but is definitely the fun part for me.

It seems generally that the heavier and more rigid the reed plate mounting is the better; brass reed frames are a lot heavier than aluminium ones (more mass), glued-in blocks are better than ones mounted on gaskets (more rigidity). Also big area pallet holes in a thin pallet board are better (my Oakwood used big rectangular holes), as is a clear open path for air flow to the reed. Bigger holes don't use more air, by far the smallest cross-section in the air flow path is the reed in its frame.

So it'll be interesting to see what flat-mounted reeds (short air path) Allen-bolted down to a milled aluminium "reed pan" with no gaskets sound like, the reed should think it's mounted directly on a big rigid metal block and you can't much get more massive and rigid than that...  ;)

Ian
Title: Re: Reed Block Acoustics
Post by: pgroff on February 18, 2012, 03:02:28 PM
Hi Ian,

I have wondered about integral, milled soundboard/reedplates, but thought of the plates waxed on. Probably your idea of screwed-on reedplates would be more secure in case of temperature changes.

I have played a highly customized Hohner Amatona (a 4 voice D/D#) years ago, owned by a very creative and handy guy.  The reedblocks had been modified to have metal bases (aluminum or stainless, I can't remember which), machined to exactly mate surface-to-surface on a metal soundboard, and locked in place to yield an airtight metal-to-metal fit with no gasket.  This box had a really unique, rich, bright and present sound, but it had many other modifications also (for example the original grille was off and an open, curved metal "collar shape" installed) and I don't know what it sounded like before the reedblocks were modified.

PG
Title: Re: Reed Block Acoustics
Post by: pgroff on February 18, 2012, 03:11:21 PM
You may be on to something with the mention of starting transients. It's well known that much of the recognisable character of the sound of a musical instrument is in the way the notes start. Snip those off recordings of a flute and a trumpet playing the same note, for example, and they sound surprisingly similar. The speed of starting also affects the feel of the instrument for the player, and is a major difference between good reeds and bad reeds.


Anahata, this observation (and ukebert's) is crucial -- thank you! It might deserve another topic.  But in my opinion, this factor also is highly influential in the differences among playing styles developed by good musicians who play dance music.  Some musicians seem to have developed a style using very high bellows pressure to get quick response and good articulation of rhythms at a micro time scale, and this can work with reeds that are less than optimally efficient and/or somewhat leaky instruments. You can achieve the accuracy without harshly overblowing the reeds on the attack.  Other musicians have a lower-pressure style that depends on extremely efficient reeds and very tight instruments to achieve those great dance rhythms.  Each approach can sound accurate and tonally beautiful, on the appropriate instruments for each style.

PG
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 18, 2012, 04:06:17 PM
I do not strongly doubt the argument that it doesn't too much matter the material of the block, and my recent balsa block project helps confirm that, but if so, why does it make such a drastic difference if the reed is on an aluminum or brass base?  Why shouldn't the material that the plate is attached to also make a difference?  I also think there is a distinction between what make no difference and what can make a little difference. A little difference can be the difference between preferring this accordion or that one.

So I'm guessing that it's to do with the stiffness of the plate. If the plate vibrates then it is going to (probably adversely) affect the sound. And the plate is a large area which is attached by wax, which is pliable. So the plate is the most likely part of the block to vibrate. I hear what you are saying and agree that probably the material of the block does make a little bit of difference, but that the construction of the block makes far more of an affect.

Quote
With my last 2 projects, I also helped confirm Digitonix's report that a bigger sound hole is better, which also kills what I had previously thought.  I assumed that a hole needed to be big enough, but too big would use too much air.  So I made square holes, which added quite a bit more surface area than my round holes.  I can tell no difference in air consumption, but a noticeable difference in volume and richness of sound. Still can't help but think there is a point of diminishing returns.

There is a point of diminishing returns, but I think that would come when the hole comprises the majority of the chamber, i.e. at the point at which you stop having a chamber and instead have a semi-enclosed space. One of the papers that I linked to showed that having a chamber gave better response at the 1-3kHz range, which is what we perceive as "definition" (I'm told). So if you stop having a chamber at all then the sound will change a fair bit. But for a conventional melodeon that would never happen.

Quote
Back to blocks. Also as an experiment, I made my blocks on another accordion (with my conventional maple blocks) with dual level chambers.  The thought was since the push/pull reeds are set the space of the plate apart, I would try to take up that space under the push reed. First impression was inconsistent.  Some reeds seemed louder, and some choked.  So I tried shaving down the top of the raised portion under the tip of the push reed, problem solved.  My next 3 will also have these stepped chambers, so hopefully I'll be able to see if it is consistently better than what I had been doing.

Do you mean that you shaped the inside of the chamber such that there was less wood under the push reed? This is done in high end PAs I think, Thierry Benetoux shows some pictures of such blocks in "Sounding out the Accordion". It makes sense to do that, as it should mean that the flow to the reeds is more consistent across push and pull. I think.

Quote
My experiments have very little scientific thought, but a whole lot of "what if..",but is definitely the fun part for me.

Don't knock yourself, this is how innovation happens, by people trying things out!

You may be on to something with the mention of starting transients. It's well known that much of the recognisable character of the sound of a musical instrument is in the way the notes start. Snip those off recordings of a flute and a trumpet playing the same note, for example, and they sound surprisingly similar. The speed of starting also affects the feel of the instrument for the player, and is a major difference between good reeds and bad reeds.


Quite. The question is to what degree the flat mounted reeds give a different sound. For instance, there is a difference between quicker response and a different mechanism. Both may be transient (probably would be), but the interesting thing is knowing whether the difference in sound is due to a different mechanism or the same mechanism being excited in a slightly different way. The first is a definite argument for flat mounted reeds, the other encourages experimenting with making block mounted reeds respond better, as diatonix and Bryan have done.

So it'll be interesting to see what flat-mounted reeds (short air path) Allen-bolted down to a milled aluminium "reed pan" with no gaskets sound like, the reed should think it's mounted directly on a big rigid metal block and you can't much get more massive and rigid than that...  ;)

Ian

I literally cannot wait to find out. Got a due date yet?

Anahata, this observation (and ukebert's) is crucial -- thank you! It might deserve another topic.  But in my opinion, this factor also is highly influential in the differences among playing styles developed by good musicians who play dance music.  Some musicians seem to have developed a style using very high bellows pressure to get quick response and good articulation of rhythms at a micro time scale, and this can work with reeds that are less than optimally efficient and/or somewhat leaky instruments. You can achieve the accuracy without harshly overblowing the reeds on the attack.  Other musicians have a lower-pressure style that depends on extremely efficient reeds and very tight instruments to achieve those great dance rhythms.  Each approach can sound accurate and tonally beautiful, on the appropriate instruments for each style.

This is quite true and is one of the problems with studying musical instruments - you can create the best musical instrument in the world for one particular thing and people can turn around and say "But I want it to do x". There is no right answer and there is no definitive best sound. Which from a scientist's point of view is a bit of a pain but from a musician or builder's view is one of the most exciting things about working with instruments.

I have played a highly customized Hohner Amatona (a 4 voice D/D#) years ago, owned by a very creative and handy guy.  The reedblocks had been modified to have metal bases (aluminum or stainless, I can't remember which), machined to exactly mate surface-to-surface on a metal soundboard, and locked in place to yield an airtight metal-to-metal fit with no gasket.  This box had a really unique, rich, bright and present sound, but it had many other modifications also (for example the original grille was off and an open, curved metal "collar shape" installed) and I don't know what it sounded like before the reedblocks were modified.

I'm struggling to visualise a collar shaped grille, but that idea for the reedblocks is interesting, it seems that gaskets do have quite an impact on how the box sounds, which isn't altogether surprising. So Ian's box will be very interesting in that regard.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 18, 2012, 04:19:39 PM
  but that the construction of the block makes far more of an affect.

Quote

But I don't think we should concentrate on just the things that have the biggest affect, the little nuances can make the difference in a good sounding accordion, or an exceptional one, and vice versa.
 

 

Do you mean that you shaped the inside of the chamber such that there was less wood under the push reed? 

Quote


There is more wood under the push reed.  The push reed is the thickness of the reed plate higher than the pull reed, so I added a strip of wood to take that amount of space up.

Also big area pallet holes in a thin pallet board are better (my Oakwood used big rectangular holes), as is a clear open path for air flow to the reed. Bigger holes don't use more air, by far the smallest cross-section in the air flow path is the reed in its frame.


Ian

Additionally, my assumptions, also maybe wrong, were that there should be some degree of pressure build up in the chamber, not for volume but tone.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 18, 2012, 04:21:16 PM
And I obviously know even less about using the multiple quote feature
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 18, 2012, 04:31:53 PM
But I don't think we should concentrate on just the things that have the biggest affect, the little nuances can make the difference in a good sounding accordion, or an exceptional one, and vice versa.
 

This is perfectly true. What I meant was that it is conceivable that the material of a reedblock might make a noticeable affect on the sound and it is conceivable that it doesn't. The difference between them may be that one has a different construction than the other. i.e. that the construction can make the affect of the material so tiny that you wouldn't notice it. But of course, the only way to know is to test it, which you have done (:)

Quote
There is more wood under the push reed.  The push reed is the thickness of the reed plate higher than the pull reed, so I added a strip of wood to take that amount of space up.

Sorry, typed the wrong thing. Yes, that's what is described in Sounding Out. You found that it improved the response of the push reed?

Quote
Additionally, my assumptions, also maybe wrong, were that there should be some degree of pressure build up in the chamber, not for volume but tone.

You may be right, but I think that Ian's point was that the resistance of the reed is so huge compared to the hole that increasing or decreasing the resistance of the opening by changing the hole diameter isn't going to change the pressure in the chamber hugely. Correct me if I'm wrong Ian. With a larger hole, however, the air flow will be cleaner and more direct into the chamber, which is important for the sound.

I think I'm using affect and effect wrong. This is what 4 years of studying a numerate subject does to you :P
Title: Re: Reed Block Acoustics
Post by: sine labore on February 18, 2012, 04:37:32 PM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.
Title: Re: Reed Block Acoustics
Post by: Anahata on February 18, 2012, 05:22:01 PM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.

Oh good - you're going to come back and tell us all the answers  ;)
Title: Re: Reed Block Acoustics
Post by: IanD on February 18, 2012, 05:25:51 PM
But I don't think we should concentrate on just the things that have the biggest affect, the little nuances can make the difference in a good sounding accordion, or an exceptional one, and vice versa.
 

This is perfectly true. What I meant was that it is conceivable that the material of a reedblock might make a noticeable affect on the sound and it is conceivable that it doesn't. The difference between them may be that one has a different construction than the other. i.e. that the construction can make the affect of the material so tiny that you wouldn't notice it. But of course, the only way to know is to test it, which you have done (:)

Quote
There is more wood under the push reed.  The push reed is the thickness of the reed plate higher than the pull reed, so I added a strip of wood to take that amount of space up.

Sorry, typed the wrong thing. Yes, that's what is described in Sounding Out. You found that it improved the response of the push reed?

Quote
Additionally, my assumptions, also maybe wrong, were that there should be some degree of pressure build up in the chamber, not for volume but tone.

You may be right, but I think that Ian's point was that the resistance of the reed is so huge compared to the hole that increasing or decreasing the resistance of the opening by changing the hole diameter isn't going to change the pressure in the chamber hugely. Correct me if I'm wrong Ian. With a larger hole, however, the air flow will be cleaner and more direct into the chamber, which is important for the sound.

I think I'm using affect and effect wrong. This is what 4 years of studying a numerate subject does to you :P

Exactly what I meant -- almost all the pressure drop will be across the reed, what seems to matter most for sound is clean air flow -- especially to the tip of the reed where most of the air flows -- and least obstruction in the air path.

This is why with normal reed blocks the lower reeds are mounted "tips up", so the air flow from the pallet hole goes up the cavity and out past the reed tip; if they're "tips down" the air flow has to kind of reverse direction. The highest reeds work better "tips down" because this allows a smaller reed cavity and there is much less air flow anyway.

With flat-mounted reeds placed with the tip end directly over the pallet hole the path is more direct still and with less resistance to air-flow because it doesn't have to flow along a cavity, it can just go straight past the reed tip without even turning 90 degrees.

The only time when big chambers are really needed is with low bass reeds which start slowly, and being big tongue area and relatively flexible are prone to choking if the pressure in the chamber builds up before they've started. A big chamber will slow down the rate of pressure change when the pallet opens, and also allows air to flow around the reed more easily if there's a big clearance to the walls of the chamber. This is probably why Helikon basses often have the lowest and octave reeds on one plate; the upper one starts faster and helps to relieve the pressure in the (big) chamber. However this then means less air for the higher reed (quieter) once the low one does start, so might not always be such a good thing unless you want the "parp-y" tuba sound...

I've measured the size of the chamber in the reed blocks on my 3 D/G boxes, and there seems to be good correlation between the quality of the bass reed sound (and resistance to choking) and the size of the chambers (biggest is best). It seem that often these aren't big enough in melodeons, especially small ones -- the reed blocks need to be deeper, wider or both.
Title: Re: Reed Block Acoustics
Post by: IanD on February 18, 2012, 05:30:07 PM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.

Oh good - you're going to come back and tell us all the answers  ;)

I think the problem is that *nobody* knows all the answers for free-reed instruments, there's been far too little serious investigative work (as opposed to anecdotes or opinions) done on them to see what really affects the sound -- or at least, that has been published so people know about it...
Title: Re: Reed Block Acoustics
Post by: Andrew Wigglesworth on February 18, 2012, 05:53:54 PM
... and to throw another spanner in the works, we're dealing with human perceptions.

We all blithley go along thinking that we "hear sound" when in fact this is a creation of the human brain interpreting reactions from parts of the body. The interpretation is also acclimitised to particular experiences and the environment. People brought up using different languages will even hear human speech differently with one group completely unable to differentiate certain sounds that are plainly separate for another group.

This is not to say that things are unknowable, and I'm not throwing in a bit of "woo" to say that science is meaningless, far from it. But if anyone thinks that you can simply wave a sound pressure meter and an osciloscope at a melodeon and come up with a definitve answer then I think they are misguided.

Psycho-acoustics I think it's called.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 18, 2012, 06:01:16 PM


I think the problem is that *nobody* knows all the answers for free-reed instruments, there's been far too little serious investigative work (as opposed to anecdotes or opinions) done on them to see what really affects the sound -- or at least, that has been published so people know about it...

That's true, we all just guess based on our ideas and our own experiences, and it's so hard to experiment because of the huge amount of time it takes to build the components.  What has always amazed me is how efficient and well thought out turn of the century accordions were considering how new the concept was.  Taking into account technology and improved materials, we have not really improved accordions nearly as much as we should have.  Maybe technology is our problem. ::)
Title: Re: Reed Block Acoustics
Post by: Andrew Wigglesworth on February 18, 2012, 06:06:19 PM


I think the problem is that *nobody* knows all the answers for free-reed instruments, there's been far too little serious investigative work (as opposed to anecdotes or opinions) done on them to see what really affects the sound -- or at least, that has been published so people know about it...

That's true, we all just guess based on our ideas and our own experiences, and it's so hard to experiment because of the huge amount of time it takes to build the components.  What has always amazed me is how efficient and well thought out turn of the century accordions were considering how new the concept was.  Taking into account technology and improved materials, we have not really improved accordions nearly as much as we should have.  Maybe technology is our problem. ::)

Maybe it's perfect already  :P
Title: Re: Reed Block Acoustics
Post by: IanD on February 18, 2012, 06:41:45 PM
... and to throw another spanner in the works, we're dealing with human perceptions.

We all blithley go along thinking that we "hear sound" when in fact this is a creation of the human brain interpreting reactions from parts of the body. The interpretation is also acclimitised to particular experiences and the environment. People brought up using different languages will even hear human speech differently with one group completely unable to differentiate certain sounds that are plainly separate for another group.

This is not to say that things are unknowable, and I'm not throwing in a bit of "woo" to say that science is meaningless, far from it. But if anyone thinks that you can simply wave a sound pressure meter and an osciloscope at a melodeon and come up with a definitve answer then I think they are misguided.

Psycho-acoustics I think it's called.

Nobody said you should only use measurements, though these help if you know what you're looking for. For example it's easy to tell louder from quieter, or brighter from softer tone. But what you want to know is what people prefer.

So you try out different things and compare them using a panel of listeners and see which they like best. So long as this is done in an unbiased way, you then *are* finding out what people want to listen to -- it's science, but based on perception.

As was pointed out, the problem is the amount of time and effort to do all this. Just trying few different things for a melodeon would take an entire thesis i.e. several years of work, and for no money. This kind of investigation has been done with various aspects of violins on several occasions, but there's no university department specialising in the acoustics of melodeons :-(
Title: Re: Reed Block Acoustics
Post by: mory on February 18, 2012, 07:41:27 PM
It would be interesting to see the airflow in various settings of reeds/blocks/hole size/shape etc can't you set some thing up ukebert, you know Slow mo camera, glass sided chambers, smoke machine, etc, a wind tunnel for free reeds or maybe this is taking the science to far and we could just enjoy the results we already have! Does advanced tech equal better? springs on valves allow faster sounding reeds and yet a lot of people condemn fast playing, squeezing in more voices mean upright blocks but flat mounted reeds (Preciosa Lilly Cajun) are louder for less reeds whats a worthy advance and whats more for the sake of more, not forgetting that this seems to be the age we are living in and does the way a reed is ground provide a surface for the air to pick up on and should reeds be ground differently dependant on the intended mounting position flat/upright and angle of input of airflow. I'm sure many of our minds rattle with the unanswered ponderables I know mine does. We need more definitive answers from the scientific community else we all perish from the weight of it all. Personally as interested as I am in all this (I am I am) I'm also entirely happy with the accumulated knowledge and its practical application carried out by that little community in Italy and all the other makers of the world that use their base of knowledge (and parts) and not forgeting the Germans how could one forget the germans and the wonderful work they did spreading the squeeze box to remote places like Brazil, Argentina, Africa, etc, etc, not least our own fondness for their product, but dam those Chinese, who do they think they are the liberty ! Oh yeah they invented it that's right  ;D does any one know of a Japanese produced box ? be interesting if they got involved look what they did with the guitar not to mention their crotch rockets. All in good spirit, All the Best mory
Title: Re: Reed Block Acoustics
Post by: Andrew Wigglesworth on February 18, 2012, 08:24:35 PM
... and to throw another spanner in the works, we're dealing with human perceptions.

We all blithley go along thinking that we "hear sound" when in fact this is a creation of the human brain interpreting reactions from parts of the body. The interpretation is also acclimitised to particular experiences and the environment. People brought up using different languages will even hear human speech differently with one group completely unable to differentiate certain sounds that are plainly separate for another group.

This is not to say that things are unknowable, and I'm not throwing in a bit of "woo" to say that science is meaningless, far from it. But if anyone thinks that you can simply wave a sound pressure meter and an osciloscope at a melodeon and come up with a definitve answer then I think they are misguided.

Psycho-acoustics I think it's called.

Nobody said you should only use measurements, though these help if you know what you're looking for. For example it's easy to tell louder from quieter, or brighter from softer tone. But what you want to know is what people prefer.

So you try out different things and compare them using a panel of listeners and see which they like best. So long as this is done in an unbiased way, you then *are* finding out what people want to listen to -- it's science, but based on perception.

As was pointed out, the problem is the amount of time and effort to do all this. Just trying few different things for a melodeon would take an entire thesis i.e. several years of work, and for no money. This kind of investigation has been done with various aspects of violins on several occasions, but there's no university department specialising in the acoustics of melodeons :-(

No disagreements here, it would indeed be science. My point was on the anec... no, actually, I'll stop there  :-X

There's a level or point at which all this merely becomes speculation on anecdotal speculations and you have to say "meh, I'll wait for the peer reviewed paper, thanks" (which as you point out, may take a while  :( ).
Title: Re: Reed Block Acoustics
Post by: oggiesnr on February 18, 2012, 09:26:22 PM
While I don't have the equipment to do it, I don't think that we're talking about that complicated an experiment.

We're measuring sound right?  Not whether we like it or not, but whether it changes? So we need measuring equipment, no problem in an acoustic lab, a bellows system (motorised so as to be consistent), one reed and a variety of reed blocks/fixing systems compatible with that reed.  One set of measurements for each of the different reed blocks, one set of measurements for each fixing method with each reed block.  There will either be a difference than can be measured or not.

Second or maybe third year degree project stuff.

Steve
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 19, 2012, 01:39:32 AM
Exactly what I meant -- almost all the pressure drop will be across the reed, what seems to matter most for sound is clean air flow -- especially to the tip of the reed where most of the air flows -- and least obstruction in the air path.

Glad to know that we are in accord :P What I don't know is the exact affect of this clean flow on the sound. I mean, I know what it does in a hand-wavey way, but none of this is backed up by experiment yet.

As was pointed out, the problem is the amount of time and effort to do all this. Just trying few different things for a melodeon would take an entire thesis i.e. several years of work, and for no money. This kind of investigation has been done with various aspects of violins on several occasions, but there's no university department specialising in the acoustics of melodeons :-(

I dunno, looking at the difference between flat mounted reeds and blocked reeds would make quite a nice 4th year project, I have a friend (as previously stated) who is doing something very similar, just with a different  sound generation mechanism. So it could be split into more manageable chunks than the years that it would take to look at the whole picture. Your point about the money is well founded though :P And I think that the Engineering Department at Cambridge would be really interested and I even know of two contacts who between them could make it happen, but self-funded. If I wasn't so bored of being a student and was good enough to do it then I'd be tempted. As it is I just want to get out of that place :P

It would be interesting to see the airflow in various settings of reeds/blocks/hole size/shape etc can't you set some thing up ukebert, you know Slow mo camera, glass sided chambers, smoke machine, etc, a wind tunnel for free reeds or maybe this is taking the science to far and we could just enjoy the results we already have!

This was my original idea for my fourth year project and I talked to some people in department and the conclusion was that it would be a really interesting MPhil project but too complicated and expensive for a fourth year project. Flow visualisation, if you want it done properly, is expensive, there is no getting around that. PIV would be the way to do it, but that requires quite a lot of investment in order to set up. Smoke is difficult - a friend of mine filled his lab with smoke and set off the fire alarm three times before giving up. What you can do is get the sound out, get the physical movement of the reed and get the flow in and out. With those bits of data you can draw some important conclusions, but they have to be based on accepted wisdom for what the flow does in the chamber.

While I don't have the equipment to do it, I don't think that we're talking about that complicated an experiment.

We're measuring sound right?  Not whether we like it or not, but whether it changes? So we need measuring equipment, no problem in an acoustic lab, a bellows system (motorised so as to be consistent), one reed and a variety of reed blocks/fixing systems compatible with that reed.  One set of measurements for each of the different reed blocks, one set of measurements for each fixing method with each reed block.  There will either be a difference than can be measured or not.

Second or maybe third year degree project stuff.

It isn't second year or third year, I can tell you that much. It's a taught masters level project, I know, doing one at the moment :P I think you oversimplify things slightly, most significantly in that all of that needs to be built be somebody! The way that research projects work is that the rig is designed in full by the student and then usually built by the technicians, aided by the student. So the student has to be able to design it themselves, which isn't trivial by any means. Building a bellows system is a bit of a nuisance. What I'd do is what my friend did and build a perspex tunnel connected to the pressurised air system in the lab with a valve such that you can precisely control the flow going into the reed chamber. That is a lot simpler than a bellows system. Remember that this needs to be repeatable and you need to eliminate all variables that you can. So just getting a load of reedblocks and testing them is going to prove nothing, they all have different materials, geometries and constructions, there is too much to test. I would make two reed chambers being the same dimensions, the same construction and the same material (would probably 3D print them for repeatability) and the only thing that would be different would be the position of the hole. I'm not sure how I would clamp them, I'd probably put in a flange to screw them down securely. Both flanges would feature on both blocks obviously. I would also have to think about how to secure the reed, probably screwing again, which would probably involve inserts on the blocks. The experiment should probably be carried out in an anechoic chamber, which isn't too difficult, but there is demand for these and you'd have to make your case to whoever is in charge of it. Measuring flow and pressure isn't too bad, nor is controlling it. You'll need a microphone with a flat frequency response and good quality microphones cost a lot of money. But if you have a decent microphone then measuring the sound shouldn't be a problem. You'll also need an amplifier and a junction box to process the data in such a way that your computer can read it. And software to process it, such as MATLAB. If you want to measure the physical movement of the reed then by far the most effective way is through a laser vibrometer. These do not add mass (which obviously changes the pitch of the reed!) and can do multiple scan points extremely quickly. Mine cost department £100,000 but you can get slightly cheaper ones. In fact there is one in the corner of my lab not being used that would be perfect for the job. Then there is flow visualisation, but that would be research masters level and I know little about it except that it is not easy.

And you'd need to do far more than one measurement! First you'd have to do a set with one block and one reed, to check how repeatable the experiment is. Then, assuming that you're getting constant results, you can take it off and dismount the reed, then putting it together and measuring it again. If that works then you try on different days and at different ambient conditions. That is all useful data. If you get the same results then you know that things are good. You then repeat that with the other block. Then you'd have to measure the sound out for each block at a range of different flow rates, repeating each experiment a number of times so as to be sure that you are getting a representative sample. It will be tricky to set up the system so that it measures transients well, so that will take a while to get right. You'll then need to measure the physical movement of the reed using the vibrometer, again at lots of different flow rates. You'd be taking a lot of data off the system and things are going to go wrong, so you'll have to repeat whole batches of experiments once you realise that you haven't taken something into account. There will be some days where you get no data at all, there will be some days where the system just will not work. It will take months of effort just to get the initial results. And once you have the results then you have to analyse them and no matter how straightforward this seems it will take forever. This is called "research". It is an art and I am finding out to my cost that it is not easy!

So it isn't a complicated experiment, but even a simple experiment has a lot of things that need to be thought about. Take my friend. He is academically and practically brilliant, he got a first in his bachelors and is a decent machinist. He is exactly the sort of person who does very well in research. He is aiming to do something very similar using similar kit. It took him a month and a half to get decent data, it's now 4 months into the project and he thinks that he has some results. He still has to do a fair bit and he'll probably finish doing his analysis at the 5 month mark. Then he'll write up, which will take about a month. So it's a good 6 months work, spending about 25 hours a week in the lab, so working around other work (as this is only worth half of the masters). And that would be to just test the difference between flat mounting and block mounting. If you want to look at the effect of the cassotto, or tapering or material or construction or different reeds or plate materials or any of the other things that we've discussed then you'll need to build a new experiment and start over again. So whilst you can make a nice 4th year project out of some of this, a nice MPhil project out of other parts, you won't be able to cover everything except in a PhD.

p.s. forgot to mention that my friend designed his rig last July and got it built over the summer so that he could start work at the beginning of the year, so that isn't included in the 6 months.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 19, 2012, 02:01:05 AM
p.p.s. People may be interested in this guide to amateur experimentation written for musical instrument makers by my supervisor: http://www2.eng.cam.ac.uk/~jw12/JW%20PDFs/Notes%20on%20acoustical%20measurement.pdf
Title: Re: Reed Block Acoustics
Post by: sine labore on February 19, 2012, 03:20:47 AM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.

Oh good - you're going to come back and tell us all the answers  ;)

I note all that you write.  I shouldn't be so arrogant as to be welcomed on to a site and then flood it with opinions.

There are some people on this thread with very evident knowledge in the matter of sound technology as well as in music and I am in a learning situation on both counts.  I had hoped to see whether I could perhaps look at melodeon sound as a project of my course if the opportunity arose.
Title: Re: Reed Block Acoustics
Post by: blafleur on February 19, 2012, 11:59:36 AM
But opinions is all any of us really have, actually it's more theories with a few opinions thrown in. ;D
Title: Re: Reed Block Acoustics
Post by: IanD on February 19, 2012, 12:05:03 PM
A couple of comments on Ukebert's post -- most of which -- as an engineer knowing the Eng Lab at Cambridge very well -- I agree with :-)

Simulating the air flow sounds easy, but whether it can be done in a sensible amount of computing time is the issue. According to the simulation software manufacturers their software is perfectly capable of simulating the chips we're designing, but to do this in enough detail would take years of real time (on a 128-CPU cluster) to get useful results; if you simplify the simulation to the point where it runs in useful time, you discard exactly the details that you're looking for. It's the kind of scale of problem that jet engine manufacturers have to deal with, and they have rather large budgets (both time, effort, money and supercomputers). Maybe if I could get access to the Fujitsu K supercomputer ('cos I know the engineers who designed it, in fact I met them last week at an award ceremony in Japan) this could be overcome, but I somehow think the Japanese government has first call on it...

So you're down to building stuff and measuring/listening to it. You don't need an anechoic chamber for free-reed measurements, a cardioid mic placed a few inches away will reject room reflections almost completely. But you do need someone to spend a lot of time building stuff with different materials/construction and this is where the time/effort would go; compared to this doing the measurements is easy.

Also doing anything significantly different in reed/frame construction in particular is a lot of work, the machinery is built to make standard reeds in standard frames so anything else has to be either done by hand (the old way) or using CAD/CAM machining (the new way). If I remember correctly there was one paper only about a new way of making high-frequency reeds with better volume and tone by shaping the reed and/or frame, and just this was a 3-year PhD.

I'd love all this to happen and be taken seriously but it would need a university engineering department to drive it, and multiple postgraduate students to work on it over several years. Anyone know any suitable heads of department who play melodeon?

Ian
Title: Re: Reed Block Acoustics
Post by: IanD on February 19, 2012, 12:06:30 PM
But opinions is all any of us really have, actually it's more theories with a few opinions thrown in. ;D

True, but some of those theories are based on genuine understanding of material science and acoustics  ;)
Title: Re: Reed Block Acoustics
Post by: oggiesnr on February 19, 2012, 06:26:15 PM
Thinking further, do you need to use bellows at all?  What we are after is a constant airflow so would a fan (suitably ducted) be sufficient?

Steve
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 19, 2012, 07:14:41 PM
Simulating the air flow sounds easy, but whether it can be done in a sensible amount of computing time is the issue. According to the simulation software manufacturers their software is perfectly capable of simulating the chips we're designing, but to do this in enough detail would take years of real time (on a 128-CPU cluster) to get useful results; if you simplify the simulation to the point where it runs in useful time, you discard exactly the details that you're looking for. It's the kind of scale of problem that jet engine manufacturers have to deal with, and they have rather large budgets (both time, effort, money and supercomputers). Maybe if I could get access to the Fujitsu K supercomputer ('cos I know the engineers who designed it, in fact I met them last week at an award ceremony in Japan) this could be overcome, but I somehow think the Japanese government has first call on it...

That isn't my area, but I agree that this would be an expensive route to take. And I don't think it's strictly necessary at this level. I think that a lot of conclusions can be drawn by measuring rather than simulating, once we have a better idea of what might be going on then it might be a good idea simulate... and by then the technology might have moved on. No point throwing money at something unless you know what to look for.

Quote
So you're down to building stuff and measuring/listening to it. You don't need an anechoic chamber for free-reed measurements, a cardioid mic placed a few inches away will reject room reflections almost completely. But you do need someone to spend a lot of time building stuff with different materials/construction and this is where the time/effort would go; compared to this doing the measurements is easy.

You're probably right re: the chamber. My friend is using an anechoic chamber because he has quite a complex sound and needs to get rid of room hum and the compressors in the floor below... whoever decided that the appropriate place to put an acoustics lab was above the compressors and below the supersonic wind tunnels was an idiot. But you are right that probably with a free reed that won't be necessary. And I'd say that once you know how to do them the measurements are easy - the trick is getting to that stage, especially if you were doing something from scratch. It takes a long time to get decent measurements out of a system. But if you already know what you are doing (as I am finding out now) then you can whiz through them like anything.

Quote
Also doing anything significantly different in reed/frame construction in particular is a lot of work, the machinery is built to make standard reeds in standard frames so anything else has to be either done by hand (the old way) or using CAD/CAM machining (the new way). If I remember correctly there was one paper only about a new way of making high-frequency reeds with better volume and tone by shaping the reed and/or frame, and just this was a 3-year PhD.

Agreed. I think that investigating current systems of mounting and so on is very straightforward, but as soon as you start looking at the reeds themselves then things get very difficult. But if you use a standard reed then there is still a lot that you can conclude.

Quote
I'd love all this to happen and be taken seriously but it would need a university engineering department to drive it, and multiple postgraduate students to work on it over several years. Anyone know any suitable heads of department who play melodeon?

As I said, Cambridge might well be up for it, the problem is money. Finding a sponsor would be tricky, department funding is very competitive and few have the money to self fund themselves.

Thinking further, do you need to use bellows at all?  What we are after is a constant airflow so would a fan (suitably ducted) be sufficient?

This is what I was suggesting, a compressed air supply, a proportional valve (or similar) and a duct to the reed. Controllable and repeatable.
Title: Re: Reed Block Acoustics
Post by: Mike Averill on February 19, 2012, 07:22:45 PM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.

Thats a fun course; I did it last year. Its very weighted to the music side though,lacks the serious physics/engineering rigour. The tutors are free reed friendly. I took my concertina to a day school at Milton Keynes and there were other free reeders there. Used it for the final examined assignment too.
Title: Re: Reed Block Acoustics
Post by: mory on February 19, 2012, 08:24:23 PM
Maybe if I could get access to the Fujitsu K supercomputer ('cos I know the engineers who designed it, in fact I met them last week at an award ceremony in Japan) this could be overcome, but I somehow think the Japanese government has first call on it...
said it would be interesting if the Japanese got involved, mory

Thinking further, do you need to use bellows at all?  What we are after is a constant airflow so would a fan (suitably ducted) be sufficient?

This is what I was suggesting, a compressed air supply, a proportional valve (or similar) and a duct to the reed. Controllable and repeatable.

Maybe a good place to start might be to get some measurement for air pressures likely to be created from your average player with average reeds, average bellows, playing in an average manner at the point of exit into an average reed chamber etc etc I think you would encounter a huge range of variables in this area alone and you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly, you would also encounter the moisture aspect of compressers so you'd have to filter as well or not AtB mory
Title: Re: Reed Block Acoustics
Post by: sine labore on February 19, 2012, 09:20:21 PM
This thread is most interesting to me as I have started an Open University Technology of Music Course and this discussion seems in point.  I shall bookmark it and return to it when (if) I learn something from the course.

Thats a fun course; I did it last year. Its very weighted to the music side though,lacks the serious physics/engineering rigour. The tutors are free reed friendly. I took my concertina to a day school at Milton Keynes and there were other free reeders there. Used it for the final examined assignment too.

I am pleased to hear from someone else who has attended this course and has some similarity of interests to myself. I feel that I shall find the mathematics/physics elements a bit daunting as I haven't undertaken any serious study for many years and maths. was never my forte.

From the comments on this thread I now feel that I shall be unlikely to add anything from the Technology of Music course to the wealth of knowledge that obviously exists here already, and instead I shall concentrate on enjoying the course as you did, and learning about the melodeon/accordion in a more relaxed fashion, as perhaps it should be.  Keep in touch.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 19, 2012, 11:54:56 PM
Maybe a good place to start might be to get some measurement for air pressures likely to be created from your average player with average reeds, average bellows, playing in an average manner at the point of exit into an average reed chamber etc etc I think you would encounter a huge range of variables in this area alone and you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly, you would also encounter the moisture aspect of compressers so you'd have to filter as well or not AtB mory

Well the lab has a compressed air supply which is filtered. It would be much more of a problem if you didn't have that facility. I don't think that you would necessarily need to measure air pressure from players, a few calculations should give you an order of magnitude and it wouldn't be difficult to put the thing together and vary the pressure such that it sounds well and to find the bounds within which it does.
Title: Re: Reed Block Acoustics
Post by: Anahata on February 20, 2012, 07:57:06 AM
you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly

Aside: I'm pretty certain that the objectionable fluttering effect you get when playing near a fan is caused by reflections of the sound off the blades interfering with the direct sound, not by modulating the air pressure supplied to the reeds.

Nevertheless I agree that you need a controlled source of air pressure for useful measurements, and it would be useful to know what pressures are generated inside a typical instrument.
Title: Re: Reed Block Acoustics
Post by: mory on February 20, 2012, 08:11:07 AM
you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly

Aside: I'm pretty certain that the objectionable fluttering effect you get when playing near a fan is caused by reflections of the sound off the blades interfering with the direct sound, not by modulating the air pressure supplied to the reeds.

Nevertheless I agree that you need a controlled source of air pressure for useful measurements, and it would be useful to know what pressures are generated inside a typical instrument.

Not so sure about reflection, I can understand why you might think so with a large blade ceiling fan but, you get the same effect with a six inch blade cooling fan at a variety of speeds but, generally seems more so when facing at the box, I'm thinking of the release pressure from the reeds not the imput pressure, maybe about turbulence? still the proof is in the science so I'll leave it to those that wish to prove or disprove it. All the Best mory
Title: Re: Reed Block Acoustics
Post by: Telemorris on February 20, 2012, 05:23:22 PM
As a builder I do not worry too much about what to make my reed blocks from. My personal choice is alder: it works easily, it is stable, resistent and not too heavy, glues well. It is also relatively inexpensive. I also used abachi in two or three batches, but continuous exposure to its dust may lead to health issues...
My priorities: Sound improves noticeably when the blocks are glued straight on the board (no bottom, no gasket, no screws). Large sound holes. Following this simple recipe you should get more or less the same result as with flat mounted reeds.

Are reed blocks that are glued to the soundboard the standard type of reed block that stand up or are you referring to flat mounted reeds?Would you provide photos of your blocks that are glued straight on the board please?

Thanks!
Title: Re: Reed Block Acoustics
Post by: diatonix on February 20, 2012, 08:18:50 PM
@Telemorris:
 https://www.facebook.com/media/set/?set=a.1314690187123.2040831.1226742509&type=3#
(Album #1  picture 66)
Title: Re: Reed Block Acoustics
Post by: Telemorris on February 20, 2012, 08:43:57 PM
@Telemorris:
 https://www.facebook.com/media/set/?set=a.1314690187123.2040831.1226742509&type=3#
(Album #1  picture 66)

Olav, Thanks for the links to your photos. One further question (I hope). How do you seal your reeds to the blocks? There's very little room for waxing. Do you use a special tool for waxing the reeds in?

Thanks!

Ed
Title: Re: Reed Block Acoustics
Post by: Owen Woods on February 21, 2012, 01:00:46 AM
Whilst we're on the subject of asking diatonix for stuff, I would love to see details of his register mechanisms... :P
Title: Re: Reed Block Acoustics
Post by: bender on April 05, 2012, 03:12:07 PM
I just came across this thread and found it interesting, and I also enjoyed the open mindedness and curiosity from the posters.  It's not a very old thread, so I can perhaps chime in, though I don't mean to re-hash a lot of worn topics.  

Concerning vertically mounted, tapered reed blocks, I was surprised to find no post that put forward the simplest explanation for why they are tapered.  If the vertically mounted blocks were not tapered, the vibrating reed tongues would collide with the reeds on the face of the adjacent block.  Therein, I think, lies the simple, practical reason.  I think it has little to do with acoustics, air flow, or reed response, and more to do with the necessity of cramming vibrating reeds into a confined space.    

In a little more detail, the pitch (distance) between reeds is determined primarily by the keyboard - the spacing between keys.  Here, convenience to the musician is paramount.  This pitch also primarily serves to define the width of the reed plates, and of course, the port hole, through which air passes to and from the reed.  For circular holes, then, this pitch also primarily fixes the minimum distance between reed blocks.  I do believe that we'd like this hole to be as large as possible, in order not to restrict air flow, but also to allow sound energy to escape.  Thus, one might try to increase this flow area by the use of rectangular holes, but with rectangles, and with the dimension between reed blocks variable, the issue is one of diminishing returns.  This distance is also constrained by the consequences to overall size and weight of the instrument.  Thus, we must settle for more or less square holes.

With the cross section of the air port now determined, and with vertically mounted blocks, it is now imperative that the blocks taper towards the top, and that the largest reeds be mounted "tip up," if the blocks are to be packed as tightly as possible.  Tight packing is of course a requirement for small, lightweight construction of the entire instrument. The largest reeds determine the taper simply because they are the ones with the largest swing during vibration.  (I don't see anything to gain by mounting the reed blocks along non parallel lines.)  With such a geometry, the smallest reeds can be mounted either tip up or tip down, simply because their swing is so small.  As some posters have noted, some small reeds are mounted tip down, and my feeling is that this is better, whenever possible, because the mounting will likely result in louder, more responsive reeds, as in flat mounted reed blocks.  Of course, there's a danger here in introducing non-uniform timbre in the sound of the reeds, moving along the keyboard.  My gut feeling is that such a danger is of little concern, simply because the (hearable) number of overtones of the smallest reeds are so small that their sound is close to sinusoidal to start with.  In rare instances, a tip down mounting is necessary in order to prevent the choking caused when the reed cavity length is too close to 1/4 wave resonance.  But such choking can be dealt with in other ways.  

I realize there were other issues covered in this thread, but I don't have the time right now to look more carefully into it, and I'm not sure if this message on an old thread will even be regarded.    

Best regards,
Tom
Title: Re: Reed Block Acoustics
Post by: mory on April 05, 2012, 04:08:22 PM
Welcome Tom interesting comments and yes definitely overlooked aspects regarding proximity. Great to have you on board, your work is much admired by some here and your technical expertease will certainly be a boost to some of the exchanges. All the Best mory
Title: Re: Reed Block Acoustics
Post by: Quebecois on April 05, 2012, 04:49:24 PM
Interesting indeed.
I have recently been putting together a melodeon out of parts of other boxes, and experimenting with the reedblocks. The bass side of a Pokerwork-type box can represent challenges with the old and big 'T' Hohner plates, and other that are even thicker, like the Cagnoni Macchina.  In some cases the rivets from the plates on the two reedblocks almost touched each other! Putting some tip down was the only option, and did not seem to affect the sound negatively.

Title: Re: Reed Block Acoustics
Post by: Owen Woods on April 07, 2012, 03:24:06 PM
I just came across this thread and found it interesting, and I also enjoyed the open mindedness and curiosity from the posters.  It's not a very old thread, so I can perhaps chime in, though I don't mean to re-hash a lot of worn topics.  

Hi Tom, you are certainly very welcome here! And I have no objection to my thread being revived. As you will see, no conclusion was reached particularly with the difference between flat and block mounted reeds, so it isn't a worn topic at all! Thanks for your comments, it may well be so that the principle reason of tapering the chambers is the reed travel, although I remain convinced that the airflow has something to do with it. Did you think that my summary (esp of your article) in the first post was meaningful?
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 07, 2012, 04:08:47 PM
Little quote from Frans van der Aa on Facebook

  I find again (and again) a better way to make the perfect reed blocks.

  http://www.youtube.com/watch?v=lNu6bYCfd7w (http://www.youtube.com/watch?v=lNu6bYCfd7w)

Seems I'll find out in November  8)
Title: Re: Reed Block Acoustics
Post by: bender on April 08, 2012, 12:34:39 AM
Hi Ukebert, In your paragraph, I think you captured many of the key ideas I tried to get across in my paper, and I'm glad they were communicated.  Although I may be overlooking something, I see no reasonable physical basis for the claim that airflow considerations explain the reason for the taper in vertically mounted reed blocks. 

I am curious, are you reasonably convinced that flat mounted reed blocks sound differently than vertically mounted ones?  If so, do you prefer the sound of one over the other? 

Best regards,
Tom
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 08, 2012, 08:02:38 AM
Kept out of this as I don't 'make' .. but it seems obvious to me that ...  ;)


That'll be 2p please  :|glug

you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly
Aside: I'm pretty certain that the objectionable fluttering effect you get when playing near a fan is caused by reflections of the sound off the blades interfering with the direct sound, not by modulating the air pressure supplied to the reeds.
edit Anyone remember Dick Nudds playing his "ol tremelodeon" in the 80's  - had a tiny bellow pressure fan inset AFAIR. Wacky and definately 'modulated'
Title: Re: Reed Block Acoustics
Post by: mory on April 08, 2012, 09:53:37 AM
Quote[ That'll be 2p please ]

you haven't allowed for inflation  ;)
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 08, 2012, 10:13:28 AM
Oooh yes I have! - play mostly on the pull  ;D

 .. off to Sheffield for their "Sessions Festival"  :|glug
Title: Re: Reed Block Acoustics
Post by: IanD on April 08, 2012, 12:03:53 PM
Kept out of this as I don't 'make' .. but it seems obvious to me that ...  ;)

  • Tapered block = tapered resonance chamber behind the plate.  In most instruments this has massive consequences, for examples organ pipes are segregated into straight and tapered sets, and the lovely (or otherwise) tone of a clarinette has (I'm told by makers) all to do with geting the taper just right on their reamer
    .
  • It's common to treat the block as an 'infinite mass' in accoustic terms (ie forget it), but that ain't the case? There is massive coupling from the action/reaction at the base of reed, and we've dicussed how without a coupling strap between blocks, the tone can go t1ts up on some notes. That coupling into block/box is so strong on my Gaillard that I feel the keyboard vibrate when playing low notes ..  makes it a second "sounding" board (as opposed to fondo)!  I think BG has made it super thin for that effect. Makes such a lovely hollow sound as you tap, that I considerered Carty style 'percussive' play for a while, though (as on guitar), I'm no Carty

That'll be 2p please  :|glug

you'd have to use a tanked air source as any one who has played near a ceiling fan or a cooling fan will tell you and I'm sure your aware, it plays havoc with the air pressure, it fluctuates and the reed responds accordingly
Aside: I'm pretty certain that the objectionable fluttering effect you get when playing near a fan is caused by reflections of the sound off the blades interfering with the direct sound, not by modulating the air pressure supplied to the reeds.
edit Anyone remember Dick Nudds playing his "ol tremelodeon" in the 80's  - had a tiny bellow pressure fan inset AFAIR. Wacky and definately 'modulated'

Sorry Chris but I have to disagree, you're doing the same extrapolating-from-very-different-instruments thing that always kicks off the "soundboard" discussions ;-)

The bore taper in wind instruments (organ pipes, clarinets) is critical because it has a very strong effect on the acoustics, the bore is comparable to a sound wavelength and is responsible for the resonances that produce the sound.

The cavity taper in reed blocks is not in any way comparable because the chambers are far too short and not resonant, see Tom Tonon's paper about reed block acoustics.

I do agree that treating the block as a rigid "infinite mass" is wrong for melodeons, hence the coupling straps. However you can build a melodeon in a way which is much closer to the ideal case, see the "A New Maker in England" thread... :-)

Ian

P.S. AFAIK the Kipper's "Tremelodeon" was just tuned with a ludicrous amount of tremolo, no fans were involved.
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 08, 2012, 12:48:52 PM
Ah, so the melodeon fourier is a pure sine wave? No harmonics. That explains why the chamber makes no difference  ;)  And that vibration of the fingered is reflected off the fan?
Title: Re: Reed Block Acoustics
Post by: IanD on April 08, 2012, 01:02:20 PM
Ah, so the melodeon fourier is a pure sine wave? No harmonics. That explains why the chamber makes no difference  ;)  And that vibration of the fingered is reflected off the fan?

Nope, plenty of harmonics. But go and work out what the resonant frequencies for melodeon reed chambers are, then you can conclude why they have little or no effect except maybe on the very highest reeds -- and why resonances are almost certainly a bad thing, not a good one (narrow-band high-Q resonances at almost-random frequencies which suck energy out of the reed are never a good idea). Tom Tonon's paper goes into this in detail.

Reed block cavities are tapered (if they are) to give the reed and valve room to swing while minimising the enclosed air volume. Resonance has little or nothing to do with it, again see Tom's paper.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on April 08, 2012, 05:26:03 PM
Hi Ukebert, In your paragraph, I think you captured many of the key ideas I tried to get across in my paper, and I'm glad they were communicated.  Although I may be overlooking something, I see no reasonable physical basis for the claim that airflow considerations explain the reason for the taper in vertically mounted reed blocks.

I'll freely admit that I know little about the subject. I should do, I have an exam on Aeroacoustics in less than three weeks which has lots of applications to box design, but as of yet I know none of it. What I do not know is whether the flow of the air has any noticeable affect on the sound. Or rather, I know that it does, since cassotto instruments sound so distinct, but to what extent? If we imagine two reeds mounted at 45 degrees and minus 45 degrees from  the vertical, meaning that the chambers are a triangle and a trapezium, the airflow is going to be very different in each of them. Does this make a difference? This is what I am not sure about, as I admittedly can't think of a mechanism. But then my problem at the moment is that I am struggling to understand what does make a definite difference, i.e. what makes a good reed or a good reedblock.

Quote
I am curious, are you reasonably convinced that flat mounted reed blocks sound differently than vertically mounted ones?  If so, do you prefer the sound of one over the other? 

No. I am convinced that my flat mounted box (http://www.youtube.com/watch?v=YqvSBmCnQR8) sounds very different to my block mounted box (http://www.youtube.com/watch?v=Ow3_Uws-11I) :P Which as you know isn't quite the same thing. diatonix on this thread has suggested that the difference is down to the fact that flat mounted reeds tend to be mounted on pans glued to the fondo, whereas blocks tend to be clamped to gaskets, which allow the block to move (c.f. reedblock straps). However my little box has a flat mounted pan clamped to the fondo, the other voice being glued.
Title: Re: Reed Block Acoustics
Post by: bender on April 08, 2012, 06:43:46 PM
If we imagine two reeds mounted at 45 degrees and minus 45 degrees from  the vertical, meaning that the chambers are a triangle and a trapezium, the airflow is going to be very different in each of them. Does this make a difference?

In the operation of reeds, there's a great distinction between the steady, or time averaged, or mean flow of air and the oscillatory (unsteady, or time dependent) vibrations produced in the air.  It seems to me you are visualizing and focusing only on the mean flow of the air.  It is the air vibrations that give rise to the sound we here, and thus, it's this motion that we need to focus on if we are to understand how different reed blocks influence sound.  This oscillatory motion is governed by concepts that are absent from a purely steady state treatment. 

Trying to understand the sound of a reed by focusing only on the mean, steady flow is like trying to understand the operation of Alternating Current circuits through application of only Direct Current concepts.  In the analogy, we understand clearly that capacitors and inductors, for instance, behave very differently to AC current than they do to DC current.  DC current cannot pass across a capacitor, whereas AC current can.  An ideal inductor behaves as a short circuit to a DC current, whereas it supplies an electrical inertial resistance to an AC current. 

Acoustics is an inherently unsteady (time dependent) phenomenon, and if you leave out this feature, you lose everything that explains how the reed is able to generate sound. 

Best regards,
Tom
Title: Re: Reed Block Acoustics
Post by: IanD on April 08, 2012, 07:09:24 PM
If we imagine two reeds mounted at 45 degrees and minus 45 degrees from  the vertical, meaning that the chambers are a triangle and a trapezium, the airflow is going to be very different in each of them. Does this make a difference?

In the operation of reeds, there's a great distinction between the steady, or time averaged, or mean flow of air and the oscillatory (unsteady, or time dependent) vibrations produced in the air.  It seems to me you are visualizing and focusing only on the mean flow of the air.  It is the air vibrations that give rise to the sound we here, and thus, it's this motion that we need to focus on if we are to understand how different reed blocks influence sound.  This oscillatory motion is governed by concepts that are absent from a purely steady state treatment. 

Trying to understand the sound of a reed by focusing only on the mean, steady flow is like trying to understand the operation of Alternating Current circuits through application of only Direct Current concepts.  In the analogy, we understand clearly that capacitors and inductors, for instance, behave very differently to AC current than they do to DC current.  DC current cannot pass across a capacitor, whereas AC current can.  An ideal inductor behaves as a short circuit to a DC current, whereas it supplies an electrical inertial resistance to an AC current. 

Acoustics is an inherently unsteady (time dependent) phenomenon, and if you leave out this feature, you lose everything that explains how the reed is able to generate sound. 

Best regards,
Tom

This could be one reason why flat-mounted reeds sound different; when the vibrating reed travels above the frame a pulse of air travels down through the frame, with flat-mounted reeds this is already travelling towards the air hole under the pallet but with reed blocks it has to make a 90 degree turn (or get reflected, which amounts to the same thing).

It's also possible that inside a reed block the pulse gets reflected off the back of the chamber back towards the reed, which doesn't happen with flat-mounted reeds (at least, if the free end of the reed is over the pallet hole).
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 09, 2012, 08:24:30 AM
Theory is all very good and I can waffle on as well as any.  We need experiment, or we'll twitter about this forever. I guess a constant pressure of air input (to keep simple) and I haven't cracked the problem of switching it on and off. Fast Fourier Transform programs can be downloaded for free, but you'd need a decent microphone into your sound board.

Variables

I'd be particularly interested in whether screwing a thin wood baffle to the block changes anything, and whether there are any changes to the harmonics if the chamber geometry varies. I accept that it's a Helmholz resonator at main tone wavelengths, but that won't IMHO be true of the higher harmonics whose wavelengths are similar to chamber dimensions. And it's these that govern the dynamics of a reed's sound as not many of us play constant tones.

Anyone up for this? (the attached sketch is just an idea)  I lost my own workshop with the last house and am now in a little flat.  Perhaps someone's tuning rig might be adapted?
Title: Re: Reed Block Acoustics
Post by: IanD on April 09, 2012, 10:35:16 AM
The reed chamber isn't even a Helmholtz resonator at most reed frequencies, it's much too small and the hole is too big -- again, see Tom's paper (or you can work it out from standard design equations for reflex loudspeakers).

Again as Tom said the chambers can have resonances (Helmholtz and cavity) at higher overtones of the high reeds, but the effects are unpredictable to say the least, and there's no way to get the chamber sizes to vary together with the reed frequencies because the range of sizes would be massive -- and if you don't do this the sound would be very inconsistent from reed to reed. I agree that nobody plays "constant tones" but a reed doesn't generate a sinewave, it has lots of high harmonics; but using resonances to affect these won't work consistently, just look at the dimensions involved.

(reed chamber length would have to vary over an 8:1 range to cover 3 octaves)

The dynamics of the sound -- reed starting and stopping -- are also little affected by chamber volume as such, the "response time" of the chamber (how long it takes air pressure to build up when the pallet opens) is much shorter than the time it takes the reed swing to build up, you can work this out from the size of the chamber and hole and the speed of sound.

The shape of the chamber and where the reed is placed compared to the pallet hole are much more important since these affect the air flow past the reed; if the chamber is "too small" it's the effect on air flow (constricting it) that matters, not the volume of the chamber as such -- this might sound like I'm being picky, but I'll bet that a small chamber with good airflow from reed to pallet hole will sound far better than a large chamber with poor airflow.

Resonances might be a good thing for violins and guitars, but they're undoubtedly a bad thing for free-reed instruments since they tend to absorb energy from the reed; extrapolating from stringed instruments to free reed is just plain wrong.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on April 09, 2012, 12:35:55 PM
In the operation of reeds, there's a great distinction between the steady, or time averaged, or mean flow of air and the oscillatory (unsteady, or time dependent) vibrations produced in the air.  It seems to me you are visualizing and focusing only on the mean flow of the air.  It is the air vibrations that give rise to the sound we here, and thus, it's this motion that we need to focus on if we are to understand how different reed blocks influence sound.  This oscillatory motion is governed by concepts that are absent from a purely steady state treatment. 

Trying to understand the sound of a reed by focusing only on the mean, steady flow is like trying to understand the operation of Alternating Current circuits through application of only Direct Current concepts.  In the analogy, we understand clearly that capacitors and inductors, for instance, behave very differently to AC current than they do to DC current.  DC current cannot pass across a capacitor, whereas AC current can.  An ideal inductor behaves as a short circuit to a DC current, whereas it supplies an electrical inertial resistance to an AC current. 

Acoustics is an inherently unsteady (time dependent) phenomenon, and if you leave out this feature, you lose everything that explains how the reed is able to generate sound. 

This is all true, but considering unsteady flow, the chamber shape is still going to make a difference to that flow, no? I don't know much about unsteady flow (although I probably should, c.f. my exam in 3 weeks time), my fluids training has been in steady flow most of it. My question is whether the chamber shape makes a difference to the flow and whether that is significant in terms of sound.

This could be one reason why flat-mounted reeds sound different; when the vibrating reed travels above the frame a pulse of air travels down through the frame, with flat-mounted reeds this is already travelling towards the air hole under the pallet but with reed blocks it has to make a 90 degree turn (or get reflected, which amounts to the same thing).

It's also possible that inside a reed block the pulse gets reflected off the back of the chamber back towards the reed, which doesn't happen with flat-mounted reeds (at least, if the free end of the reed is over the pallet hole).

Aye, the first is what I think happens. But I really don't know enough about the science to know whether it makes a difference. Maybe I should start revising...

Theory is all very good and I can waffle on as well as any.  We need experiment, or we'll twitter about this forever. I guess a constant pressure of air input (to keep simple) and I haven't cracked the problem of switching it on and off. Fast Fourier Transform programs can be downloaded for free, but you'd need a decent microphone into your sound board.

http://forum.melodeon.net/index.php/topic,8904.msg110818.html#msg110818 :P

I would be interested in doing this, but I don't have anything at the moment. As I mentioned there, department does and in 3 years time if my friend is still studying Aeroacoustics after his PhD I might try to persuade him to investigate free reeds. I would try it myself, but I don't have the ability really to do anything in department.

The shape of the chamber and where the reed is placed compared to the pallet hole are much more important since these affect the air flow past the reed; if the chamber is "too small" it's the effect on air flow (constricting it) that matters, not the volume of the chamber as such -- this might sound like I'm being picky, but I'll bet that a small chamber with good airflow from reed to pallet hole will sound far better than a large chamber with poor airflow.

Quite.
Title: Re: Reed Block Acoustics
Post by: Quebecois on April 09, 2012, 03:50:26 PM
 This is all very interesting but still does not explain why an old grey Paolo sounds like it does, or a Pokerwork has that Hohner sound!  I wonder if the designers of the boxes that became so popular since the 1940's ever went that far in studying all of the acoustics phenomena. One can get obsessed with technology, others will simply enjoy playing their box and enjoying the sound! People get more impressed with your playing than the scientifiic precision of the reedblocks...  ::)
Title: Re: Reed Block Acoustics
Post by: IanD on April 09, 2012, 04:18:23 PM
This is all very interesting but still does not explain why an old grey Paolo sounds like it does, or a Pokerwork has that Hohner sound!  I wonder if the designers of the boxes that became so popular since the 1940's ever went that far in studying all of the acoustics phenomena. One can get obsessed with technology, others will simply enjoy playing their box and enjoying the sound! People get more impressed with your playing than the scientifiic precision of the reedblocks...  ::)

So should we just not bother trying to improve things, and assume that sprinkling some magical grey Paolo fairy dust on a melodeon immediately makes it sound better?

-- remember that everyone *knew* that the sound of a Stradivarius was unsurpassed, until blind tests showed that it wasn't ;-)

I listen to music on a perfectly average stereo system not a top-notch expensive hi-fi, because I'm interested in enjoying the music not the equipment.

But it seems to me that it should be possible to make a melodeon which would be better to play and sound better (which leads to a happier musician), because to be honest the design has essentially been stagnant for almost a century in design, construction methods and materials.

And since we're discussing what might accomplish this, the normal way to do that is to use some objective scientific analysis to try and determine what might improve the sound and what should have little or no effect -- trial and error using pure guesswork went out a long time ago when the scientific method was invented. I'm sure that it is perfectly possible to explain the sound of a grey Paolo or a Hohner, it's just acoustics and materials not rocket science.

-- yes I know, rocket science is easy, it's rocket engineering that's difficult...

Since the scientific method worked for the guy who set out with the supposedly impossible task of building a violin which sounded better than a Strad -- and succeeded according the the blind tests by experienced musicians and listeners -- this seems a good enough reason to apply it to the melodeon...
Title: Re: Reed Block Acoustics
Post by: Quebecois on April 09, 2012, 04:52:34 PM
But it seems to me that it should be possible to make a melodeon which would be better to play and sound better (which leads to a happier musician), because to be honest the design has essentially been stagnant for almost a century in design, construction methods and materials.
Perhaps things are fine as they are! The "sounding better" thing is a very subjective topic, as no two humans have the same hearing... What sounds "good" on an oscilloscope may not be perceived as such by humans.

Guitars have been built the same way for over a century. Fabrication methods have evolved, with new tools, glues, finishes, strings, etc but essentially the instrument has received no "improvements" for a long time: it's just fine like it is. Same with the piano, brass instruments, etc. Why do we need a "new" melodeon?

There has been experimental instruments since the early 20th century, with plastic guitars, metal violins, other instruments made of acrylic or plexiglas material, etc. Yet, people always came back to the good old design. Why is it that so many people are seeking so many old instruments, instead of buying new ones? It's because they "sound" and play better! According to them...


 
Title: Re: Reed Block Acoustics
Post by: oggiesnr on April 09, 2012, 06:47:52 PM

But it seems to me that it should be possible to make a melodeon which would be better to play and sound better (which leads to a happier musician), because to be honest the design has essentially been stagnant for almost a century in design, construction methods and materials.


Therein lies the problem, your play and sound better may well be my play and sound worse.  I dislike the Baffetti Binci's and most Castagnaris, either the sound does nothing for me or the action is too responsive so a "better" box that had these traits would leave me cold.  That being said I love what some people can do with their BBs and Castas, I just don't want to make that sound or play that instrument.

I don't see the fact that design has been stagnant (and I think I disagree with that statement) is a problem.  Recorder design has been similarly stagnant and it seems to work.  IMHO what we have is an instrument that can be made at a variety of different price points, yet all of which are similar enough that we can basically pick up any of them and play one, but have a wide variety of tonal quality and responsiveness to suit all tastes.  I'm not sure that what we're trying to do is expensively redesign something that ain't broke.

Steve
Title: Re: Reed Block Acoustics
Post by: IanD on April 09, 2012, 10:33:20 PM
There's a basic difference in philosophy here; I'm always looking for better ways to do things in the belief that they can be improved (it's my job as well, and the evidence suggests I'm usually right there), other people are happy to assume that things are fine just as they are and/or that something has already been raised to the peak of perfection by many years of artisanal endeavour.

So those who like things just as they are -- don't worry, be happy, I don't have a problem with that. But don't shoot people down who want to improve things, after all we'd still be all banging rocks together to make music if nobody had ever made any advances in instrument design :-)

Of course "improve" may be subjective, nobody likes all the same things and it would be a sad world if they did. I don't like sweet-sounding dry-tuned 3-voice boxes but other people do, that's fine by me. I also think something can be done to make the type of instrument I like (2-voice box for English and similar dance music) better, so I'm going to try and do that together with Andrew.

If I like the result then as far as I'm concerned we'll have succeeded. I don't expect everyone to like the result, because it'll probably be like very hoppy beer -- you either love it or hate it. But if it works I suspect quite a lot of people will love it...

(and if it doesn't work out, well that's the way the cookie crumbles -- if you don't try anything new you'll never find out what doesn't work)

Ian
Title: Re: Reed Block Acoustics
Post by: Owen Woods on April 09, 2012, 10:50:17 PM
I don't have much time, so I won't respond properly now, I'll leave that till later in the week. But suffice it to say that I agree wholly with Ian and those who think that designs have been constant should look again (especially into the Piano!) and should read my last blog post (http://ukebert.wordpress.com)
Title: Re: Reed Block Acoustics
Post by: Quebecois on April 10, 2012, 02:40:34 AM
One day the Buddha met an old man sitting by a river, and asked him what he has done with his life. The man replied: "I spent the last 50 years learning how to walk on the water, and I think I am just about to succeed". The Buddha replied: "Wouldn't it be easier just to use a boat?"
Title: Re: Reed Block Acoustics
Post by: IanD on April 10, 2012, 09:35:27 AM
One day the Buddha met an old man sitting by a river, and asked him what he has done with his life. The man replied: "I spent the last 50 years learning how to walk on the water, and I think I am just about to succeed". The Buddha replied: "Wouldn't it be easier just to use a boat?"

If the boat was called the Titanic, perhaps some improvements would be a good thing...

P.S. Quebecois, if you're so against proposals for improvements, you don't have to read this thread and waste your valuable time replying to it ;-)
Title: Re: Reed Block Acoustics
Post by: george garside on April 10, 2012, 10:04:26 AM
or that something has already been raised to the peak of perfection by many years of artisanal endeavour.

 ???????? the mind boggles !!!!!!!

george  >:E ;D
Title: Re: Reed Block Acoustics
Post by: IanD on April 10, 2012, 10:52:59 AM
or that something has already been raised to the peak of perfection by many years of artisanal endeavour.

 ???????? the mind boggles !!!!!!!

george  >:E ;D

Artisanal, not courtesanal :-)
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 10, 2012, 10:59:06 AM
If the boat was called the Titanic, perhaps some improvements would be a good thing...  P.S. Quebecois, if you're so against proposals for improvements, you don't have to read this thread and waste your valuable time replying to it ;-) 

Mainly it was going too fast and not looking ahead properly. I'm frankly amazed the ship's captain ended up "a hero" in the ensuing brouhaha! With regard to melodeons I'm not with Québécois either. I've seen some notable advances in the 25 years I've been playing and that was one reason I set up the 21st Century Box thread (http://forum.melodeon.net/index.php/topic,7840.0.html). 

Playing heritage instruments is nice too, particularly if you are into heritage music. But we don't know it all and might note that - since we used to play Wheatstones at the f'c'stle ..  self righting lifeboats have replaced self-rightious newspapers!  ;)
Title: Re: Reed Block Acoustics
Post by: Theo on April 10, 2012, 11:28:54 AM
I'm very much in favour of innovation and admire those with the vision and energy to make come up with new ideas and refine them into workable improvements.

I do also think that to some extent there has been a continuous process of development going on in our instruments over the last century and a half.  True the basic pattern has remained much the same with a bellows in the middle, melody on the right and accompaniment on the left, and reeds mounted on wooden blocks, either upright or flat, with finger operated levers to play.   But within that basic pattern a huge variety of different materials and construction methods have been tried tested and either become common usage, or faded away.   Taking Hohner as an example we can see both stable designs that have continued virtually unchanged for getting on for 80 years in the 2915 models that we know as the pokerwork, and huge innovation in the 50s and 60s, especially in the piano accordion world with the Atlantic series.  I imagine that the design brief for these was to throw out all the old designs and start afresh.  Anyone interested in designing a new diatonic could learn much from a couple of hours going through the insides of an Atlantic.  The only wood in them is in the reed blocks, everything else is aluminium or plastic, even the reeds are a new design, and the result is an accordion that was louder and lighter than its predecessors.

From the diatonic point of view it is also worth remembering that the current range of wood finished Castagnari, Saltarelle, and other Italian boxes really hardly existed prior to about 30 years ago, but now they are common.
Title: Re: Reed Block Acoustics
Post by: george garside on April 10, 2012, 12:05:02 PM
I strongly agree that design & development should not be left to stagnate.  Genuine improvements should be retained and iffy ones dumped.  It can also take several attempts over a period of time to get new technology to work well and arguably Roland still have some way to go with their electonic melodeons.

It is also important not to 'chuck the baby out with the bathwater'  by trying to over elaborate/improve  an already brilliant design   a couple of  examples of this happening being the original Shand Special ( first Shand  Morino ) of 1939  which was a  brilliant advance on previous BCC# boxes and of which  later versions are thought by some to be not quite as good.   Another example  is the original grey Paulo Soprani BC ;boxes  which wouldn't be so sought aafter  if they werent so good and of which the present day  version is but a mere shadow (well I think so anyway)

george
Title: Re: Reed Block Acoustics
Post by: oggiesnr on April 10, 2012, 01:04:59 PM
OK, in my defence please note that I was not the one who used the word "stagnant" in relation to melodeon design and I also pointed out that I thought I disagreed with that statement anyway.

There are however times when the a product is a particular form because the basic configuration works and has been proven to work reliably.

Steve
Title: Re: Reed Block Acoustics
Post by: Quebecois on April 10, 2012, 01:21:58 PM
P.S. Quebecois, if you're so against proposals for improvements, you don't have to read this thread and waste your valuable time replying to it ;-)
True! I much prefer to spend time playing and learning new tunes on one of my "stagnant designed" boxes!
Title: Re: Reed Block Acoustics
Post by: IanD on April 10, 2012, 01:30:40 PM
OK, in my defence please note that I was not the one who used the word "stagnant" in relation to melodeon design and I also pointed out that I thought I disagreed with that statement anyway.

There are however times when the a product is a particular form because the basic configuration works and has been proven to work reliably.

Steve

Nobody (not even me!) is saying that the basic configuration of a melodeon described by Theo is fundamentally flawed, there are some very nice instruments about nowadays and have been for many years.

But all the high-end melodeons are pretty much built the same (with small detail differences) as the "new" wooden models Castagnari introduced in the 1970s after Marc Perrone persuaded them to start making them, which in turn are pretty much the same internally as the pearloid ones that many Italian makers (including Paolo Soprani) have been making since the middle of the last century. The fact that people are saying that 50-year old Paolos are some of the best boxes ever made should tell you something about how far melodeon design has progressed -- or not :-)

Most new makers try to build something a little bit better by tweaking the details of the styling and construction, but with no real re-think they end up with yet another rather nice melodeon with most of the same plus and minus points that all the others have got. Apart from using new machinery (like laser-cutting) to make something almost the same but with a more modern manufacturing method, the only maker I can think of to have even tried significantly different materials is Stormy Hyde -- and his boxes are essentially conventional in construction apart from some of the materials used.

I'm not saying that change just for the sake of change is a good thing, it has to deliver some real benefits. But apart from incremental tweaks there seems to have been no real change in melodeon design and construction for more than 50 years, so it seems to me that it might be possible to make a bigger jump forwards by *properly* using materials and techniques that didn't exist then.

If I'm wrong then you can all say "I told you so" ;-)

Ian
Title: Re: Reed Block Acoustics
Post by: Andy in Vermont on April 10, 2012, 01:38:11 PM
I agree with the basic premise that many aspects of the modern melodeon can still be improved, but I also think that the developments of Castagnari and others have been massively underestimated in statements like Ian's last 50 years" of stagnation.  I would be very interested in hearing the perspectives of engineers and physicists who can actually identify the specific 'tweaks' that make modern Castagnaris so wonderfully playable, and a more detailed accounting of the reasons why a Pokerwork with TAM reeds still doesn't match a Castagnari, and why a Castagnari with Hohner reeds doesn't perform the same as a Hohner -- as observed by Rich Morse years ago on the Squeezebox list.  There is more than just cosmetic difference.
Title: Re: Reed Block Acoustics
Post by: IanD on April 10, 2012, 03:50:08 PM
I agree with the basic premise that many aspects of the modern melodeon can still be improved, but I also think that the developments of Castagnari and others have been massively underestimated in statements like Ian's last 50 years" of stagnation.  I would be very interested in hearing the perspectives of engineers and physicists who can actually identify the specific 'tweaks' that make modern Castagnaris so wonderfully playable, and a more detailed accounting of the reasons why a Pokerwork with TAM reeds still doesn't match a Castagnari, and why a Castagnari with Hohner reeds doesn't perform the same as a Hohner -- as observed by Rich Morse years ago on the Squeezebox list.  There is more than just cosmetic difference.

I didn't say there had been no improvements (but why are 50 year old Paolos still "the best" according to some?), just a lot of small tweaks and adjustments.

Which of course add up to significant differences overall, as you say -- but you could liken this to the refinement over many years of front-engined GP cars to what was thought to be the height of perfection, only to see them all made obsolete overnight by the first mid-engined GP car which was poo-poohed as a toy by the old school. Or years of refinements to aluminium chassis and suspension designs being blown away by the introduction of carbon fibre. Changes to construction and materials can be disruptive and very successful if they work -- but see the Comet and RB211 stories for cases where they didn't...

Nobody knows whether a big change will work (or not) until somebody tries it. Then afterwards everyone says how it was obvious all along -- isn't hindsight wonderful?

Not saying that a similar step change in melodeon design will work as predicted (or positively), let's wait and see... ;-)

Ian
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on April 10, 2012, 03:52:24 PM
New 'maker invented' stuff in my boxes

Oakwood - plywood insides - really strong!
Gaillard - air (gulping) hole much much improved (van de Aa can't match it)
             cantelever rt hand mechanism (moved towards a good piano) it's super fast
             aluminimum insides - you just have to see it!
             holes in wood structure both ends 'balances middle row'
             clever bass - chromatic both ways on 18 buttons
             light keyboard- vibrates as you play - sure it helps tone!
             changed bevel on keyboard edge, really comfortable in play
             double headed bellows pins - these a PAIN - tangle in your woollies!
van der Aa - thinned reed plates (he grinds them) about 30% lighter
                  amazing action - don't know how
                   "new design for blocks" as per last week. Not seen it yet
                  improved couplers - little levers by your thumb
                  this casta couplers are really awkward!
                 Car paint "midlight blue" finish  8)

 .. OK the last one is cosmetic!  ;)               
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on September 12, 2013, 12:45:02 PM
I was reminded of this thread today when EJay spotted this video (http://youtu.be/JWToUATLGzs) and posted it to FB. However this rather more nerdy version (http://www.youtube.com/watch?v=ADGmBtLJ6y4) is probably better for our purposes.

They simulate (no more than that) a fondo in having multiple resonators on a solid board. The metronomes are all close tuned -  some spot on, out of phase - some a few 'cents' out, moving in and out of phase. Basically they all magically synchronise within minutes!

These tickers are at about 1.5Hz, so scaling to a more melodeonic ±250 Hz, I'd expect effects to evolve over say a second. Note that anything remotely harmonic on our box (eg tonic+5th played together) will also be affected, basically all harmonics will interact with similar harmonics in any active reed. The model is crude but I think this demo may scotches theoretical arguements that fondo mass/wood/stiffness etc "has no affect on tone"?  :|glug
    (http://i1.ytimg.com/vi/ADGmBtLJ6y4/mqdefault.jpg) (http://www.youtube.com/watch?v=ADGmBtLJ6y4)
click photo
Title: Re: Reed Block Acoustics
Post by: Owen Woods on September 12, 2013, 01:16:36 PM
I don't think that anyone has ever argued that the fondo has no effect on tone. What has been said is that the effect of the fondo is not due to the fondo resonating. Instead it absorbs vibration from the reed, couples blocks together and indeed, as in the metronome case, can couple reeds together. Personally though I think that the coupling of reeds within the same block would be far, far stronger than coupling reeds between blocks.
Title: Re: Reed Block Acoustics
Post by: Andrew Wigglesworth on September 12, 2013, 01:26:44 PM
Also, a reed in an accordion being driven by an air stream imparting energy into the system, and for the reed an overwhelming amount of energy that basically defines it's behaviour, is not the same as a set of metronomes sat on a board whose behaviour is defined by the decay of energy in the system.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on September 12, 2013, 01:46:28 PM
Indeed.
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on September 12, 2013, 01:51:41 PM
So why do we need metal strips tightly screwed in, linking the blocks? Slightly "sprung" metal strips in van de Aa's manufacture. I do accept that for brief notes there ain't much time to couple, but small phase shifts will affect , tone and high harmonics may coouple quicker

This is a bit like whether the galloping horse has all 4 legs off ground at one. Experiment required, this was an attempt towards such evidence.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on September 12, 2013, 01:57:02 PM
I think (Theo might correct me here) that straps are to do with reed block resonance. Energy from the reed causes the block to vibrate. When excited at its resonant frequency, the block takes a lot of energy out of the system (impedence matched, if you want to think of it like that). This causes some strange audio effects. By strapping the blocks together you introduce a constraint on the system, which shifts the resonant frequencies away (theoretically) from the playing range.

Of course, the problem is that the block size and construction does have a subtle effect on the sound, as the impedence will vary with frequency depending on the design. So by strapping them you will change the response of the instrument quite apart from losing the resonance. Most of the time this will change it for the better, but I have heard of some instruments which don't take kindly to being strapped.

The sprung strips are an interesting one. Perhaps they are a way of absorbing more energy at points other than at the resonant frequency, making a stiffer block overall (and, in crude terms, a "brighter" sound). That's just a guess though.

You are right in that we do need evidence. But when you are interested in a horse galloping then you film a horse galloping. You don't film a millipede and make assumptions from that!
Title: Re: Reed Block Acoustics
Post by: Theo on September 12, 2013, 02:02:51 PM
I think (Theo might correct me here) that straps are to do with reed block resonance.

The practical mans answer is that without the strap you can find the the tremolo on one particular reed pair will not sound the same when mounted in the instrument as is does when sounded outside the instrument.  Fit a strap and the note sounds as it should.  That much will have been observed by anyone who has done tuning work at all extensively.

The explanation is I believe more or less as ukebert states, though I would prefer to change "reed block resonance" to "resonance of the reedblocks and the system that reedblocks are part of"
Title: Re: Reed Block Acoustics
Post by: waldoB on September 12, 2013, 02:25:56 PM
This is interesting. I have a problem with four notes on two buttons on the C# row of a B,C,C#. The lowest C#/Eflat and F/F# on a 34 button treble keyboard. The best way I can describe it is that they sound ' dull ' compared to the equivalents on the B row and C rows. It's tuned MML  8 cents sharp. Its not just the higher middle reed being flat, all three individual reeds sound dull. The rest of the C# row is fine. The reeds sound the same as the others on a tuning bench. I've change offending reeds - the box all aMano, had them re-valved all to no effect. The F# pull is particularly bad. I think I've seen here that the sound you hear is what comes out of the exit from the reed block, the case acoustics are quite a minor part of what is heard. Could a strap help ? There is one midway across the five blocks already. Choking of the inner row is common on these three rows when it is buried down below the keyboard. Suggestions much appreciated.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on September 12, 2013, 02:28:20 PM
I think (Theo might correct me here) that straps are to do with reed block resonance.

The practical mans answer is that without the strap you can find the the tremolo on one particular reed pair will not sound the same when mounted in the instrument as is does when sounded outside the instrument.  Fit a strap and the note sounds as it should.  That much will have been observed by anyone who has done tuning work at all extensively.

The explanation is I believe more or less as ukebert states, though I would prefer to change "reed block resonance" to "resonance of the reedblocks and the system that reedblocks are part of"

Yep, that's fair! Nothing is ever simple ::) Everything is linked to everything else...
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on September 12, 2013, 02:45:46 PM
Just to be clear as to what I'm referring to ..
van der Aa sprung linkage, attached. He used
to install straight one's, says this is "better"
Title: Re: Reed Block Acoustics
Post by: Theo on September 12, 2013, 03:40:31 PM
I've tried both and am unable to hear any difference. Perhaps I don't know what to listen out for?
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on September 12, 2013, 03:44:58 PM

Er ….not done the experiment m'self … "boing" ?
Title: Re: Reed Block Acoustics
Post by: Anahata on September 12, 2013, 03:58:32 PM
I've tried both and am unable to hear any difference. Perhaps I don't know what to listen out for?

They may both work equally well acoustically, but possibly Van Der Aa's method is less likely to apply sideways force to the reed blocks causing gasket leaks.

Also a rigid coupling isn't needed, but something that absorbs energy. For that to work, the wire had better not be too springy.
Title: Re: Reed Block Acoustics
Post by: Chris Ryall on September 12, 2013, 04:06:34 PM
Won't a link with spring put in a phase shift?
Title: Re: Reed Block Acoustics
Post by: Andrew Wigglesworth on September 12, 2013, 04:20:36 PM
Won't a link with spring put in a phase shift?

I want one  ;D

I bet it would be great in slows.  :neigh:
Title: Re: Reed Block Acoustics
Post by: IanD on September 12, 2013, 04:47:10 PM
I think (Theo might correct me here) that straps are to do with reed block resonance.

The practical mans answer is that without the strap you can find the the tremolo on one particular reed pair will not sound the same when mounted in the instrument as is does when sounded outside the instrument.  Fit a strap and the note sounds as it should.  That much will have been observed by anyone who has done tuning work at all extensively.

The explanation is I believe more or less as ukebert states, though I would prefer to change "reed block resonance" to "resonance of the reedblocks and the system that reedblocks are part of"

If you think how the vibrating reeds (tip at the top) apply force to the reedblocks when they vibrate, it turns out that the result is a sideways force near the top of the block -- if the reeds are in phase (both in and out at the same time) the forces cancel, of the reeds are out of phase they add. This force will then drive any torsional resonances along the length of the block (e.g. with the middle and ends moving in antiphase), causing the "reed locking" effect like with the metronomes.

Anything that stops the top of the reed block moving sideways -- bracing to other reed blocks, or even better down inot the corners of the case -- will help prevent this, or at least shift the frequency. Usually such a resonance will be narrowband so only one (or maybe two) reeds will be affected. If there's more than one resonance then other reeds will also be affected, but again usually only one note. Anything that affects the effective mass or stiffness seen by the reed block -- "soundboard" thickness, screwed/glued/clipped down blocks, seal material/thickness -- will move the resonance(s). Damping the resonance might also help, or it might just make a big problem on one note into a smaller problem on several...

-- so making changes might fix the problem, or move it to somewhere else, or even make it worse -- I doubt if anyone's going to do a 3D resonance analysis of a melodeon on a computer when it's far quicker to try something and see if it works :-)

So both descriptions are correct really; the basic resonance is within the reed block, but it's affected by other things like mounting/bracing/straps.
Title: Re: Reed Block Acoustics
Post by: Owen Woods on September 12, 2013, 08:31:54 PM
Ian - so do you think that with say an MM box with both M reeds on the same block, that coupling through the block will pull the reeds in phase with one another?
Title: Re: Reed Block Acoustics
Post by: IanD on September 12, 2013, 10:53:40 PM
Ian - so do you think that with say an MM box with both M reeds on the same block, that coupling through the block will pull the reeds in phase with one another?
Yes, if there's a resonance in the block which increses the coupling between the reeds. They don't always lock completely together (no beats), they often pull in and out of lock so you get slowed down or irregular beating, which sounds particularly horrible -- my Tommy did this with the link strap removed. It's usually only one note that's affected, unless you're unlucky enough to have more than one resonance coinciding with reed fundamental frequencies.
SimplePortal 2.3.5 © 2008-2012, SimplePortal