Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4]   Go Down

Author Topic: Hide Glue Pot for Reed Wax?  (Read 12415 times)

0 Members and 1 Guest are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hide Glue Pot for Reed Wax?
« Reply #60 on: March 11, 2018, 08:04:02 AM »

It also gives a good acoustic coupling between the reed plate and the reed block, which many people feel gives a superior sound.
But it rather depends on the acoustic transmission properties of the leather used as a gasket. I'm told red leather is particularly good, especially with brass reed plates.
I couldn't comment on the colour of the leather, nor brass reed plates. But screwed reed plates with a thin gasket of olovisc (such as used by Emmanuel Pariselle on his melodeon building courses, and Rees on his one-rows) work very nicely indeed. The possible reduced acoustic transmission of the gasket material is over-ridden by the enhanced acoustic coupling of the screws going through the gasket directly into the wood of the reed block. The reed plates are in direct contact with the screw heads.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Hide Glue Pot for Reed Wax?
« Reply #61 on: March 11, 2018, 08:56:50 AM »

"acoustic coupling of the screws going through the gasket directly into the wood of the reed block. The reed plates are in direct contact with the screw heads."

Well b****r me, I'd never considered that! I'd always considered that using a gasket would detract from the sound in some way, but of course you're dead right about the plates being clamped and therefore connected via the screws. 
But.........surely if the plates are screwed directly onto the block and then sealed with wax, we should get an even clearer/cleaner sound?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hide Glue Pot for Reed Wax?
« Reply #62 on: March 11, 2018, 09:02:45 AM »


I got a button on a box to fix in a different thread, it would be hard to heat the lever where the button sits using a hot air gun without knocking of more buttons off.

For small tasks like fixing a glued on button I like to use fish glue instead of hide glue.  It has most of the advantages of hide glue gut does not require heat.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hide Glue Pot for Reed Wax?
« Reply #63 on: March 11, 2018, 09:43:04 AM »

There is an obscure point of view, aired from time to time, that putting the sound into the air is the job of the reed tongue and not the job of the reed plate, reed block, pallet board or case.

Mounting a reed on a gasket (any gasket) will tend to decouple the reed plate from the block, thus the coupling via two screws is likely to be much reduced versus the coupling of the reed plate directly mounted. Also, if you search the forum, you will find numerous posts discussing how this might be affected by the choice of wood used for the case.
Which are the best places to continue this particular sub-thread.

----------------------------------------------------------
For hide glue I have a small heated water bath container originally sold for warming baby's milk, and a small lidded pot that fits nicely into it. It is thermostatically controlled and inexpensive (a convenient birthday present request), and small enough not to get in the way.

For wax I use a similar pot sold for depilatory wax use, so rather hotter. I doubt it would stand the use required for full-time users, but again only a few quid and works well for my level of use.

Since we live in a hard water area, and use a condensing tumble drier, the waste water from the tumble drier can conveniently be used as a source of soft water to avoid scaling in the water baths,

I will look into trying fish glue next time I am playing with such things.
 
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hide Glue Pot for Reed Wax?
« Reply #64 on: March 11, 2018, 11:59:58 AM »

There is an obscure point of view, aired from time to time, that putting the sound into the air is the job of the reed tongue and not the job of the reed plate, reed block, pallet board or case.

Mounting a reed on a gasket (any gasket) will tend to decouple the reed plate from the block, thus the coupling via two screws is likely to be much reduced versus the coupling of the reed plate directly mounted.

Agree about "putting the sound into the air is the job of the reed tongue". However, the reed plate, reed block and reed block mounting needs to be as rigid as possible so that there is a maximum transference of energy to reed tongue (and hence to the air). Any reduction of rigidity of those components means that some of the energy is lost in vibrating the components, and not the reed tongue. Screwed-down reed plates help enhance the rigidity.

The analogy is like twanging a ruler on the edge of a desk. With the ruler firmly clamped to the desk top, the twanging works well. If you introduce a soft cloth between the ruler and the desk top, the rigidity is compromised and you get a phut rather than a twang.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Hide Glue Pot for Reed Wax?
« Reply #65 on: March 11, 2018, 02:43:27 PM »

I like  hide glue! ! ! , but would definitely use superglue  on a button.

I'm using superglue on frets on a guitar too, but never on wood.

Thinking about trying to use superglue as a lacquer. Just as a test.
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hide Glue Pot for Reed Wax?
« Reply #66 on: March 11, 2018, 08:29:45 PM »


I got a button on a box to fix in a different thread, it would be hard to heat the lever where the button sits using a hot air gun without knocking of more buttons off.

For small tasks like fixing a glued on button I like to use fish glue instead of hide glue.  It has most of the advantages of hide glue gut does not require heat.

thanks for that !! I'll have to see if I can find some locally.
Plenty of fish around but I haven't seen fish glue a my local lumber yard. I may have to get it online or at a woodworkers supply store in the area.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 2 3 [4]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal