Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: GDR D/G box - treble end questions (newbie - please be gentle)  (Read 1033 times)

0 Members and 1 Guest are viewing this topic.

rayhomewood

  • Ray Homewood the Old Bear (aka Gothic Toad)
  • Member
  • *
  • Offline Offline
  • Posts: 5
  • Guitarist turned to squeezeboxes and fiddle!

Hi.  I just bought an old GDR D/G box.  Three newbie questions re the treble end:

1.  Tthere are a few notes which constanly sound (albeit a bit wheezy) - it looks as if the pallets are not sitting flush - is this likely to be a case for bending the rods they sit on or could it be the springs?

2.  Also at the treble end, there is a large screw sticking up between the pallets, central lengthwise and near to the fingerboard side - could this be holding the end together, or could it be to keep the cover from bending down onto the action and pallets?

3.  Some of the treble buttons tend to get stuck down after releasing them - I think they are fouling the edge of the hole they sit in.  Is this a common problem and how can I improve it?

I would be very grateful for any tips!

Many thanks, Ray
« Last Edit: June 28, 2013, 11:35:18 AM by rayhomewood »
Logged
Kind regards
Ray Homewood : )

Tony M

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: GDR D/G box - treble end questions (newbie - please be gentle)
« Reply #1 on: June 27, 2013, 01:18:06 PM »

I'm no expert - but I've tinkered with a few of my boxes:

1)  Could be a number of causes (and possibly more than one!), partly depending on the nature of the mechanism on your box: 

-  Stiffness in the mechanism could prevent the pallets from closing fully onto the soundboard,
-  weakness in the spring wouldn't help, but if they work fairly well, they're probably OK,
-  loss of part of the leather on the pallet surface that provides the seal, or
-  a problem with the pallet closing flat against the board, as you suggest. 

I'd start with a check on freedom of movement, then, if that's OK, take a careful look to see if you can spot where the leaks are. 

Bending the rods to get the pallets to sit flat on the board is possible, but best avoided - you might end up snapping the rod.  (Been there, done that - made a new rod!).

It may be possible to avoid this risk if the rod is "pinned" to the pallet (you could just ease the pins a bit, to allow a little movement) or if it's glued to it (pehaps with a cloth disc to reinforce), in which case a gentle application of heat might soften the glue enough to allow the pallet to sit flat.

If you really need to bend, do it very gently and try not to put any strain on the ends of the rod - particularly if it's screwed into the pallet or into a wooden lever at the other end, otherwise you could have a whole new set of problems! 

"Act in haste, repent at leisure" is an appropriate mis-quote, I think!

2)   Almost certainly there to stop the cover from being bent inwards, as you suggest.

There are other, wiser heads on here than me, who will probably provide further comment.

All the best,

Tony M.
Logged

rayhomewood

  • Ray Homewood the Old Bear (aka Gothic Toad)
  • Member
  • *
  • Offline Offline
  • Posts: 5
  • Guitarist turned to squeezeboxes and fiddle!
Re: GDR D/G box - treble end questions (newbie - please be gentle)
« Reply #2 on: June 27, 2013, 02:32:33 PM »

Hi Tony - many thanks! : )
Logged
Kind regards
Ray Homewood : )
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal