Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Roller mech hot rodding  (Read 983 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Roller mech hot rodding
« on: July 20, 2024, 11:21:29 PM »

Hi All,

I'm going full-monty on my soviet box hot rod, and I'm rebuilding the left side mechs right now.
There's a video where somebody uses rubber tubing to reduce the roller mech noise:
https://youtu.be/p-LUNY97-Ww?t=97

The end result looks quite similar to what's inside some stradella mechs, however, the guy in the video just leaves the oversized rubber tubing hanging on the linkages.
A neater way would be to either use heat shrink, or pick the tubing in the same diameter as the rods.

My rods measure in at 1.57mm, so there's a choice of either natural latex with 1.6mm hole, or 3.2mm heat shrink that will end up hugging the 1.6 rod.

Does anyone have any experience using heatshrink for this job? Is there a risk of the shrink walls getting worn out with use and needing replacement? Similarly, are there any reasons to go/not to go for natural latex?

Thank you.

Thank you.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Roller mech hot rodding
« Reply #1 on: July 21, 2024, 07:49:18 AM »

In this situation I’ve successfully used silicone rubber tubing.  It’s more durable over long periods than latex, and more resilient than heat shrink. And it’s available in a wide variety of sizes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Roller mech hot rodding
« Reply #2 on: July 21, 2024, 08:28:28 AM »

Thank you very much.

From memory, silicone is quite happy to be stretched - do you think 1.5mm ID tubing is about right for 1.6mm rods?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Roller mech hot rodding
« Reply #3 on: July 21, 2024, 12:40:57 PM »

I should think so.  It’s cheap to buy so maybe worth getting a couple of sizes to compare?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Roller mech hot rodding
« Reply #4 on: July 21, 2024, 03:20:17 PM »

Yep.
I can also get PTFE tube with 1.5mm or 1.6mm id - that's interesting, as I'd expect it to have the lowest friction.
Logged

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Roller mech hot rodding
« Reply #5 on: July 21, 2024, 04:09:03 PM »

Before crimping became the default for connecting wires into multiway connectors wiremen would use a lubricant to allow friction fit sleeves (rubber or PTFE) to slide over the cable. The sleeve would then be slid back over the soldered connection for insulation.

Something like this might help you get the tightest fit possible. Available from anywhere that sells soldering sundries.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal