Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Making bass machine rollers  (Read 653 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Making bass machine rollers
« on: April 26, 2025, 02:50:39 PM »

Just finished making, installing and setting up my first roller bass machine, so here's some photos of the process.
I'm not going to cover how you link the rollers to the pallets as there are many different approaches - pick the one you like.
Also, being a lazy bugger, I've just re-cycled the pallet-lever assembly from an old accordion instead of making my own.


If making rollers by hand you have to resort to large-diameter rollers. You can get away with 3mm but it's extremely difficult to do that without wasting a bucket of rods. 4mm gives you a lot more room for error.
I chose titanium for the rollers as it's light and stiff. Brass or stainless steel are valid alternatives.
The posts are simply riveted into the rollers - even with a semi-decent riveting job there's no need for silver brazing.
Posts are brass, 1.6mm in my case.
Rollers are drilled to 1.5mm - see the riveting part for the explanation.

1) Mark your rollers for drilling. File a wee flat (in fact, I used a round file, so it's a concave "flat") so you can register an automatic punch on it. Punch the rollers in preparation for drilling.
(Test piece of Ti rod is used here).
PXL-20241002-161953937" border="0

2) Drill the rods. Be very careful to drill down the middle of the rod. If you are off centre and leave the walls too thin, they can break when riveting.
If drilling ti, go very slow with lots of lube. Why? Ask the 12 drill bits that I broke while drilling 80 holes :-[
I went a step further and reamed the holes with 1.50mm reamer after drilling them.
PXL-20240914-123715030" border="0
PXL-20241002-162006709" border="0

3) Prepare the posts. In my case 1.6mm brass goes into 1.5mm holes, so I filed a taper on the end of each post until it would fit through the 1.5mm hole and have ~3mm of the tip sticking out.
PXL-20241002-162037230" border="0
PXL-20241002-162206675" border="0

4) For riveting you'll need a jig. £3 cheapo pliers worked for me. File the jaws until they are slim enough to hold rollers with the smallest spacing between posts that you have in your design.
PXL-20241002-162141907" border="0

5) Be sure to anneal the post tips before riveting. Otherwise hardened brass can shatter and break off instead of mushrooming when you are trying to rivet it into the rollers.
Rivet the posts into the holes. Carefully file off the excess brass.
PXL-20241002-162258230" border="0
PXL-20241002-162351421-MP" border="0
PXL-20241002-162413047" border="0

That's it! Simples. You can now design & build your own bass machine. No more loitering around dumpsters waiting for somebody to throw away a melodeon with a working bass machine.

For mounting I used PTFE inserts glued with CA into wooden support blocks (file deep grooves in PTFE for CA to grab!). Drill 4mm holes with 5mm step between centers, then ream them out with 4.1mm reamer for 4.0mm rollers.
There are many alternative options though.

PXL-20250426-095601249" border="0
PXL-20250426-122329478" border="0

« Last Edit: April 26, 2025, 02:58:38 PM by mChavez »
Logged

Jerry in NZ

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: Making bass machine rollers
« Reply #1 on: May 01, 2025, 02:53:49 AM »

Just a heads-up to anyone who isn't already aware that titanium swarf is considered hazardous. It can spontaneously ignite, fiercely, and the presence of oil-based cutting fluid increases the hazard.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Making bass machine rollers
« Reply #2 on: May 01, 2025, 07:33:44 AM »

This is a very good point - it does throw pretty sparkles if you fire it up with a blowtorch (away from the workshop, obviously).
Fire safety is a key priority, especially in a woodworking shop, where you have fine wooden dust, bottles of flammable liquids, and, if you're lucky to work on accordions, piles of celluloid and bottles of acetone.

It is the first time I hear about spontaneous combustion though: do you have more information about it? I.e. Titanium swarf going on fire without any source of heat or ignition.
I always thought it needed an ignition source, and, unless it's literally in dust form, it needed quite a lot of heat to get going.
Logged

Jerry in NZ

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: Making bass machine rollers
« Reply #3 on: May 01, 2025, 10:47:23 AM »

You're right to pick me up on 'spontaneously': loose terminology, and posting only half-awake I fear. Mea culpa. Industry produces masses of finely-divided titanium waste, which is stored and transported without mishap, usually, although accidents have happened. Apparently spontaneous combustion has been reported where oil-saturated titanium swarf has been stored in hot conditions. As for other combustible metals, industry takes precautions. The main risk seems to be in the workshop, rather than storage. Ti is a poor conductor of heat, so the chips machined from the workpiece don't carry off much heat. The classic (although hopefully rare) event is where a high-speed-steel tool is machining Ti without coolant, the tool tip and built-up edge suddenly glow white, and the molten, burning blob drops into the swarf tray, and off it goes. Ti waste should also be protected from stray sparks and other sources of ignition. After all this, it may seem surprising that Ti can be TIG welded (and I'm not going to try that...).

I should have said that in some circumstances, Ti can ignite unexpectedly. My apologies.
« Last Edit: May 01, 2025, 11:21:45 AM by Jerry in NZ »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Making bass machine rollers
« Reply #4 on: May 01, 2025, 06:35:42 PM »

Thanks - I've asked because the only thing that I'm aware of having a risk of spontaneous combustion in a woodworking shop is rags soaked in boiled linseed oil (and other drying oils). Everything else, afaik, needs an ignition source.

I think we're pretty safe with ti swarf & filings as we're not removing a lot of material here, but I would most certainly not be running a dust extractor anywhere near a ti rod that's being worked and can send off a spark, so a very good health and safety warning from you!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal