Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Modifying reed chambers to accept larger or smaller reedplates  (Read 3988 times)

0 Members and 1 Guest are viewing this topic.

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog

When modifying the tuning of a melodeon by fitting different reeds to the original reedblock, what sort of mods might need to be done to the reed chambers if the replacing reedplate is larger or smaller than the original. What are the principals behind the mods - I can see that some chiseling out might be needed to allow a larger reed to vibrate, but less sure when you might need to put in an insert to reduce the volume if the reed is smaller. Any photos of chiseling-outs or inserts - what are the latter made from and are they glued or waxed in?

Any insights appreciated.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #1 on: July 30, 2012, 09:14:56 PM »

I, rather unscientifically but successfully, just chisel out blocks to accept bigger reeds, there is of course a logical limit after which you cant carve anymore wood out but not sure what you would be doing to reach this extreme.

To reduce I generally cut a plug out of whatever wood is laying around and wax it in place (this makes it easily reversible. I have also experimented with reducing the chamber capacity, again by waxing plugs in place, but can't really tell if it made a difference on the reeds I was working on*.

* As an aside on the reducing chamber size; Pokerworks with accidentals have, in my experience, either a reed block with smaller chambers to take reeds on plates sized normal to their pitch in this position or the same reed block that would take low notes but fitted with the accidental reeds fitted to large reed plates. I have not detected any difference between these two setups.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #2 on: July 31, 2012, 03:35:19 AM »


* As an aside on the reducing chamber size; Pokerworks with accidentals have, in my experience, either a reed block with smaller chambers to take reeds on plates sized normal to their pitch in this position or the same reed block that would take low notes but fitted with the accidental reeds fitted to large reed plates. I have not detected any difference between these two setups.

That's interesting Lester, if I am not misunderstanding your statement. On my own Pokerwork, the chambers at the big end of the block are graduated normally to accept the next larger reed plate, but fitted with a filler to accept the shorter reed plate of the accidental. But then I have not seen the insides of great numbers of P.W.'s
« Last Edit: July 31, 2012, 03:37:24 AM by j.w.forrest »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #3 on: July 31, 2012, 07:36:31 AM »


* As an aside on the reducing chamber size; Pokerworks with accidentals have, in my experience, either a reed block with smaller chambers to take reeds on plates sized normal to their pitch in this position or the same reed block that would take low notes but fitted with the accidental reeds fitted to large reed plates. I have not detected any difference between these two setups.

That's interesting Lester, if I am not misunderstanding your statement. On my own Pokerwork, the chambers at the big end of the block are graduated normally to accept the next larger reed plate, but fitted with a filler to accept the shorter reed plate of the accidental. But then I have not seen the insides of great numbers of P.W.'s

I'll see if I can find some example of both reed plates today and take a photo.

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #4 on: July 31, 2012, 07:40:41 AM »

Thanks, Lester.

As an aside, the other filler I have occasionally seen, only in small chambers I think, is a wedge-shaped one. What is the thinking behind that?
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #5 on: July 31, 2012, 07:48:53 AM »

Thanks, Lester.

As an aside, the other filler I have occasionally seen, only in small chambers I think, is a wedge-shaped one. What is the thinking behind that?

That is to reduce the capacity of the chamber which I guess is in turn to reduce the air flow/pressure to stop the reeds choking. I similar effect is sometimes achieved by making a hole in the wax to allow air to leak from the chamber.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #6 on: July 31, 2012, 07:49:36 AM »


* As an aside on the reducing chamber size; Pokerworks with accidentals have, in my experience, either a reed block with smaller chambers to take reeds on plates sized normal to their pitch in this position or the same reed block that would take low notes but fitted with the accidental reeds fitted to large reed plates. I have not detected any difference between these two setups.

That's interesting Lester, if I am not misunderstanding your statement. On my own Pokerwork, the chambers at the big end of the block are graduated normally to accept the next larger reed plate, but fitted with a filler to accept the shorter reed plate of the accidental. But then I have not seen the insides of great numbers of P.W.'s

I'll see if I can find some example of both reed plates today and take a photo.

Here is a reed block with accidentals on oversize plates

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #7 on: July 31, 2012, 09:25:32 AM »

I am now a bit wary of instruments which have been modified in some way where the reed plates have been shifted to chambers which have different dimensions from those originally designed for the reed plates.

For instance in a conversion for 3rd button start to fourth button start, the reed plates will be shifted up (towards the high-pitched end) by one chamber position. The obvious problems have already been discussed, i.e. where you need to ensure that the reed tongues and valves do not foul on the chamber end wall, remedied by carving out a suitable thickness of wood. However, I think this is not the only issue.

In my (limited) experience of Castagnari melodeons converted in this way, the reed chamber will still be undersized for the pitch of the note and I have noticed that this can affect the harmonics generation/absorption and hence can affect the quality of sound produced. Somehow the sound has a definite 'edge' to it which I personally find annoying after a while. Maybe I am being hypersensitive, maybe it depends on the quality of the reeds, the internal finish of the reed chambers, degree of tremolo, etc.

I have no experience of the opposite: smaller reed plates being fitted on to a larger than original reed chamber, perhaps as a result of converting a 'low-notes at the chin end' instrument to 'accidentals at the chin end'. But I suspect you would need to be aware of a possible time lag in pressure build-up in a larger chamber and consequently a possible delay in response. Also it is entirely feasible to reduce the size of the reed chamber by adding slivers and plugs of wood. But you can't easily and significantly enlarge a reed chamber without a major rebuild of the reed block. 

In conclusion I am of the opinion that (for high-end instruments at least) the reed chamber dimensions are optimised for the size of reed/plates expected to be fitted on to them and if we subsequently mess about with this, we can adversely affect the quality of the sound.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #8 on: July 31, 2012, 09:53:54 AM »

<snip>
 But you can't easily and significantly enlarge a reed chamber without a major rebuild of the reed block.
When I carve out the reed blocks I endeavour to make the reed chamber the same dimensions as the original cavity. The difference in the size of reed cavity for example adjacent cavities on a Hohner block (all I had to hand but guess it is representative) is about 5% (4233mm3 and 4022mm3) before easing the cavity to allow the valve to operate. So I don't believe there is an issue.

Quote
 
In conclusion I am of the opinion that (for high-end instruments at least) the reed chamber dimensions are optimised for the size of reed/plates expected to be fitted on to them and if we subsequently mess about with this, we can adversely affect the quality of the sound.

I think you are possibly being "hypersensitive"  ;)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #9 on: July 31, 2012, 10:57:07 AM »

<snip>
 But you can't easily and significantly enlarge a reed chamber without a major rebuild of the reed block.
When I carve out the reed blocks I endeavour to make the reed chamber the same dimensions as the original cavity. The difference in the size of reed cavity for example adjacent cavities on a Hohner block (all I had to hand but guess it is representative) is about 5% (4233mm3 and 4022mm3) before easing the cavity to allow the valve to operate. So I don't believe there is an issue.
Lester, I believe what you say about the Hohner reed blocks and it is commendable that you 'endeavour to make the reed chamber the same dimensions as the original cavity'. I don't think this is so easy on Castagnari reed blocks, as I think the taper of the blocks is greater (need to check this however). A 5% difference in volume doesn't seem much, I agree, but it nevertheless might make a discernible difference in the acoustic behaviour.

Quote

Quote

In conclusion I am of the opinion that (for high-end instruments at least) the reed chamber dimensions are optimised for the size of reed/plates expected to be fitted on to them and if we subsequently mess about with this, we can adversely affect the quality of the sound.

I think you are possibly being "hypersensitive"  ;)
Maybe I am, and I don't mind being accused of that. But all I can say is that I am not the only one to notice the difference in sound in the examples I referred to in my previous post. However, I do think that maybe with Hohner reeds which have a different sound spectrum from Castagnari (Voci Armoniche) reeds, the difference in sound quality caused by mounting them in a smaller reed chamber is perhaps not noticeable, especially if the reeds are tuned with a fair degree of tremolo.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #10 on: July 31, 2012, 01:03:12 PM »


* As an aside on the reducing chamber size; Pokerworks with accidentals have, in my experience, either a reed block with smaller chambers to take reeds on plates sized normal to their pitch in this position or the same reed block that would take low notes but fitted with the accidental reeds fitted to large reed plates. I have not detected any difference between these two setups.

That's interesting Lester, if I am not misunderstanding your statement. On my own Pokerwork, the chambers at the big end of the block are graduated normally to accept the next larger reed plate, but fitted with a filler to accept the shorter reed plate of the accidental. But then I have not seen the insides of great numbers of P.W.'s

I'll see if I can find some example of both reed plates today and take a photo.

Here is a reed block with accidentals on oversize plates


In the case of Erica/Pokerwork it would seem that Hohner place more importance on unifying the reed blocks than optimising chamber size.
As said, they used to block out the largest chamber when installing an accidental with a small /normal plate.
If they fit them with an oversize plate the chamber remains the same as that "designed" for a low note.
(I presume that the other idea, of fitting a fillet of wood, the same size as the difference in length of adjacent chambers, is to facilitate fitting differing reed sets.)
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #11 on: July 31, 2012, 01:54:01 PM »

Just to support Steve

When my Gaillard came I realised I'd made a really silly choice for an 'accidental' (actually a reversed note) C# and that it needed to be an octave higher. Bertrand sent me a suitable plate - I can't remember offhand what the other note was and I got Paul in Cleckheaton to fit it luthier fashion.  He put a fillet in there (at least - said he had) but the tone, and particularly attack of the C# is different from the push one. In a gaillard every chamber is different size/tuned so I guess there's a mismatch somehow?

I'm not gonna do anything about it as I use this Db mainly for chords with flats in, or when playing 'out' eg GAlt scale against a C melody .. where it just sounds slightly more 'out' ;)  But it is a different tone.  :|glug
Logged
  _       _    _      _ 

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #12 on: July 31, 2012, 02:13:22 PM »

Just to support Steve

When my Gaillard came I realised I'd made a really silly choice for an 'accidental' (actually a reversed note) C# and that it needed to be an octave higher. Bertrand sent me a suitable plate - I can't remember offhand what the other note was and I got Paul in Cleckheaton to fit it luthier fashion.  He put a fillet in there (at least - said he had) but the tone, and particularly attack of the C# is different from the push one. In a gaillard every chamber is different size/tuned so I guess there's a mismatch somehow?

I'm not gonna do anything about it as I use this Db mainly for chords with flats in, or when playing 'out' eg GAlt scale against a C melody .. where it just sounds slightly more 'out' ;)  But it is a different tone.  :|glug

I would agree also if I was moving a reed an octave, but I thought we were only moving reed to make a 4th button start from a 3rd.

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #13 on: July 31, 2012, 03:14:58 PM »

I don't like onions.

Some years ago my mother made some potato farls. I ate one, my father asked me why I was eating one if there were onions in them and I immediately caught that horrible taste and spat it out. He was joking, there weren't even any onions in the house.

Your senses may be wonders of evolution but, to use modern parlance, they're oh so easily pwned by the power of suggestion.
Logged

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #14 on: July 31, 2012, 04:07:08 PM »

... I thought we were only moving reed to make a 4th button start from a 3rd.

The concept that triggered my question did in fact involve up to an octave difference at the two ends. I think now that I understand what is involved better, thanks to the responses, it seems like a non-starter, and even if physically do-able could well end up with a less than ideal sound quality. But worth asking, and I have learned a lot. Thanks all.

Regarding the small reed accidental in the large chin-end chamber on Pokerworks, I recall Roger Watson explaining in a Sidmouth workshop back in the 70s that the squeeky sound of the accidentals was due to this mismatch of reed and chamber size. I think Hohner must have done something about it as it does not seem so noticeable nowadays. That workshop was also the first time I came across a Morino Club (Roger had most of the Hohner melodeon range there); I was, needless to say, gobsmacked at the quality and the sounds, but could not help but think what it really needed was a Stradella bass (but what else would you expect from a Shand Morino fan  (:)).
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Modifying reed chambers to accept larger or smaller reedplates
« Reply #15 on: July 31, 2012, 04:25:38 PM »

Regarding the small reed accidental in the large chin-end chamber on Pokerworks, I recall Roger Watson explaining in a Sidmouth workshop back in the 70s that the squeeky sound of the accidentals was due to this mismatch of reed and chamber size. I think Hohner must have done something about it as it does not seem so noticeable nowadays.
Strange,
It is only of nowadays that the reed itself has been greatly mismatched to the chamber size, previously it would have sat above a chamber reduced to the "correct "size.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal