Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Switching the push/pull on a single button  (Read 2044 times)

0 Members and 1 Guest are viewing this topic.

Peter Savage

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 441
Switching the push/pull on a single button
« on: October 10, 2012, 01:50:59 PM »

I would like to switch over the reeds on one of my accidental buttons; same notes, just the other way around (push/pull).  This must have been explained several times already on this forum, but I can't find the right thread.  Can someone point me in the right direction?  Many thanks.  Peter
Logged

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: Switching the push/pull on a single button
« Reply #1 on: October 10, 2012, 02:02:14 PM »

I'm not an accordion technician by any means.

I did this with my concertina though. I wanted to have a C# in both directions so that I could have more options for playing in the key of D. I replaced one reed with a C#/D# reed and then reversed the existing C#/D# to play D#/C#. I simply found which reed plays those notes. Took it out and turned it around and then rewaxed it.

Again, I'm not a technician so I would suggest waiting until someone with experience responds but I don't think it would be all that difficult of a procedure.
Logged
Sean McGinnis
Bordentown City, NJ, USA

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Switching the push/pull on a single button
« Reply #2 on: October 10, 2012, 02:26:35 PM »

If you are lucky it is just a matter of swapping reed plates around. Assuming it's a two voice box it will of course be two reed plates. Worst case is that the tuning goes out sufficiently that it notices as turning the plates will always change the tuning by an amount, you have got to ask yourself; Do you feel lucky Well do you punk? (puts Dirty Harry Magnum away  8) ).

If you do feel lucky tell us what box it is and more hints tips will be forthcoming

Peter Savage

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 441
Re: Switching the push/pull on a single button
« Reply #3 on: October 10, 2012, 02:58:42 PM »

Thanks for the tips gents.  It is a Castagnari Sander D/G and it is my Bflat/Gsharp button that I want to swap round so that I get the Bflat on the pull.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Switching the push/pull on a single button
« Reply #4 on: October 10, 2012, 03:07:29 PM »

So open up your box, extract the reed block with the most reeds on, the reed plates you want to swap are the ones nearest your chin when you are playing it, pop them off, swap them round, wax them in again.

I refer you to Dirty Harry above.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Switching the push/pull on a single button
« Reply #5 on: October 10, 2012, 03:25:00 PM »

Thanks for the tips gents.  It is a Castagnari Sander D/G and it is my Bflat/Gsharp button that I want to swap round so that I get the Bflat on the pull.
The Sander is a three-voice instrument, so you will need to reverse three reed plates: the M, M+ (tremolo) and the L (low octave) plates. As Lester has said, it is a matter of easing the relevant reed plates out of the holding wax, flipping them over and rewaxing back into place. You may also need to adjust the tuning a bit afterwards, but this is not always necessary for a straight forward reversal.

It is not a difficult job to do and doesn't (shouldn't) take long, but if you've never done it before and don't feel confident with the rewaxing and possible retuning, then ask a professional like Theo or Lester to do it for you.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Switching the push/pull on a single button
« Reply #6 on: October 10, 2012, 03:38:59 PM »

You should really clean off all the old wax and use new wax to re-fix the plates.  It is very difficult to do a near and tidy job by re melting the old wax in situ.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peter Savage

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 441
Re: Switching the push/pull on a single button
« Reply #7 on: October 10, 2012, 08:37:57 PM »

The need for waxing/re-waxing has scared me off completely.  I might have been on for undoing a couple of screws but waxing is a bit serious for me.  I will take it to a tuner and have it professionally done.  Thanks for helping me make the decision though; much appreciated.
Logged

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Switching the push/pull on a single button
« Reply #8 on: October 11, 2012, 07:15:49 PM »

you really shouldnt panic over waxing. I flipped them on my Sander 15 years ago reusing the wax that was there and they havent fallen out yet. The reuse issue is more associated with very old wax that has gone brittle. If its young it will be fine.
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Switching the push/pull on a single button
« Reply #9 on: October 12, 2012, 10:20:40 AM »

The need for waxing/re-waxing has scared me off completely.

Without denying that re-waxing is the best and proper way, I replaced five reed plates in my Pokerwork and they've stayed secure for over 20 years.   I did four at once to convert from low note to accidentals, and one when a reed failed.   Caveat - I had access to an electronic soldering iron which could be turned right down to just melt the wax without burning or overheating it.
Logged
Tony S
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal