Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: switches and sliders  (Read 1026 times)

0 Members and 1 Guest are viewing this topic.

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
switches and sliders
« on: October 27, 2012, 11:16:51 AM »

I recently managed to get hold of a five switch Hohner Amatona IV in B/C. It's in pretty ropey condition, but I reckon with a bit of TLC it could come good. I've noticed that some of the reed combinations work better than others, The four voice master setting sounds OK, but some of the other settings sound choked.

After taking the blocks out and carefully examining the mechanism I've come to the conclusion, that a less than expert hand has been at work. Several of the valves were bent through what looks like rough handling and in one instance a valve from one block was trapped underneath the adjacent block. I'm not convinced that all the sliders are attached in the correct order. Does anyone have experience of working with the switch mechanism on this type of box?
Logged
Semper idem, sed non eodem modo

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: switches and sliders
« Reply #1 on: October 27, 2012, 03:53:13 PM »

Hi Mike, I have had a bit if experience of slider mechanisms.  Everything is very lightly built and slight damage, or obstruction (eg from a valve) can lead to further damage if the couplers are operated forcefully.  Are the slides built in to the reed blocks, or into the underlying board?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
Re: switches and sliders
« Reply #2 on: October 27, 2012, 04:31:10 PM »

Theo,

Thanks for taking the time to reply.

The sliders fit into the reed blocks. They do not appear to be damaged (no bends or kinks), but the switches don't feel to be working evenly (i.e some move more freely than others).

I need to draw some diagrams marking what reeds are on which blocks and then I can relate that info to the movement of the switch mechanism) .

Some of the sliders give different clearance above the slot by which they are hung from the mechanical movement. I'm sure this has some significance, but I've not quite got it straight in my head.  I'll spend some more time looking and perhaps post some drawings later in the week.

AtB

Mike
Logged
Semper idem, sed non eodem modo

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: switches and sliders
« Reply #3 on: October 27, 2012, 04:49:34 PM »

If the metal slides are in good condition, but still don't move freely then it's often the case that there is a bit if distortion in the very thin layer of wood that firms the lower face of the reed block. I've successfully eased this by inserting a strip of abrasive paper into the slot where the slide goes, and working it back and forth to take the high spots off the wood.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal