Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: .  (Read 7666 times)

0 Members and 1 Guest are viewing this topic.

aradru

  • Member
  • *
  • Offline Offline
  • Posts: 42
.
« on: November 24, 2012, 04:17:04 AM »

.
« Last Edit: October 13, 2015, 01:23:01 AM by . »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing celluloid
« Reply #1 on: November 24, 2012, 10:13:27 AM »

Do you want to remove the celluloid, or just clean it?

Acetone is the best solvent for celluloid, paint stripper might remove it faster, but would make a wonderful sticky mess.   

I've found that the celluloid will usually peel off in big sheets if you can get a thin blade underneath it along an exposed edge. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing celluloid
« Reply #2 on: November 24, 2012, 10:57:01 AM »

The glue residue is usually very thin and can be sanded off, or that could be the time for the paint stripper.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Removing celluloid
« Reply #3 on: November 24, 2012, 11:26:43 AM »

Acetone is (or was at least) Nail varnish remover , should be available almost anywhere
Logged
Q: How do you cure MAD?
A: Buy more Boxes

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Removing celluloid
« Reply #4 on: November 24, 2012, 12:20:18 PM »

Hi
Don't take this as gospel but I believe there is no glue,it is actually the celluloid itself that melts and bonds,also as the celluloid sets it shrinks and tightens onto the ply box structure.

Pete
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Removing celluloid
« Reply #5 on: November 24, 2012, 12:58:41 PM »

it`s not melted but warmed til its pliable and then pressed onto the wood, there are a few clips on Youtube showing this in accordion factories , it looks like they paint the wood with acetone first, I know Theo used that method to stick celluloid on ..

Kimrick`s Weltmeister one - 52 seconds in

http://www.youtube.com/watch?v=rYsSifiDapo

I`d also go for the lifting with a stripping knife and peeling off in strips if I was to do it, maybe warm the surface first ?. melting it off with Acetone sounds awfully messy to me given how thick it is .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Removing celluloid
« Reply #6 on: November 24, 2012, 01:38:39 PM »

The celluloid is stored I think in a container of acetone and water,that's what makes it pliable
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Removing celluloid
« Reply #7 on: November 24, 2012, 03:38:00 PM »

I remember a visit to the celluloid department at the Harmona accordion factory in Klingenthal back in the mid nineties: Ashen faced workers moving around like zombies in a cloud of acetone vapours - really frightening stuff. I was told that in communist times they were provided with a generous extra allowance of free milk every day...
« Last Edit: November 24, 2012, 03:40:34 PM by diatonix »
Logged

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Removing celluloid
« Reply #8 on: November 24, 2012, 04:09:28 PM »

The one time I removed celluloid from a box I did as Theo mentioned and used a sharp blade to remove it dry without the use of solvents and sanded off the residue.

I'm actually surprised that celluloid is still even legal in the EU given how hazardous it is in all respects...
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Removing celluloid
« Reply #9 on: November 24, 2012, 04:14:27 PM »

Isn`t there two sorts, the Combusible kind (Nitrate) and a newer kind which isn`t  .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Removing celluloid
« Reply #10 on: November 25, 2012, 08:15:25 PM »

The celluloid is softened with acetone vapors. This is done by having it lay on a fine screen or cloth suspended above a container of liquid acetone in a closed sealed container. this is chilled to about 45F if I remember, as it will dissolve the celluloid if it is too warm. the room is kept cool also to give you more working time. A thin layer of glue is applied before laying down the celluloid.
 When I salvage old accordions I get a knife and peel the celluloid off, sometimes this can take of a thin layer of wood too.
 You MIGHT want to try the vapor method if you can get acetone (try a paint store) do it outside if you are worried about the vapors (despite its smell acetone does not seem to be very toxic, look it up) 15 to 20 min is usually enough at about 65F. Feels like rubber when it is softened. A plastic bucket with a snap on lid would work and a tablespoon of acetone would be enough. strip off any thing from the the box you don't want bothered by the fumes. normal wood glue on the body should be unfazed by the acetone.

 I have done repairs on accordions missing black keys , or severe body damage with good results.
You can heat it to make simple bends, but don't try anything hotter than a hair dryer, and keep some water handy, the stuff burns like a match head!
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing celluloid
« Reply #11 on: November 25, 2012, 11:54:47 PM »

You can also get the celluloid to the rubber like state by soaking it on a bath of acetone mixed with water.  1:1 mix at room temperature needs only a short time  to soften the celluloid. I suspect a mix with a lower proportion of acetone would be effective after a longer soak.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Removing celluloid
« Reply #12 on: December 02, 2012, 03:08:27 AM »

I've got a few screw holes on the front of my red paolo soprani from an old marching band music stand that used to be mounted on the front. How do I repair these holes in the celluloid? Is there any way to buy a kind of filler that will completely hide the holes? They kinda look ugly. Thanks!
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Removing celluloid
« Reply #13 on: December 02, 2012, 07:44:06 AM »

I would fill the holes with gliud in wood (from a cocktail stick, matchstick or whatever), sand it down to flush & smooth and touch up with red nail varnish with many coats, then polish up the whole area with Brasso to re-gain the shiny surface (I`m getting good at this) it`ll look pretty uniform

Another way after fillling the hole would be to use something to remove some of the glued in wood about the thickness of the remaining celluloid like a drill bit (in your hand not on a drill)  - then a trick which Charlie Marshall told me was to get a bit of celluloid and turn it into a thick paste with acetone and use it to fill in to the level of the cellulolid around and when dry sand and Brasso..
Logged
Q: How do you cure MAD?
A: Buy more Boxes

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Removing celluloid
« Reply #14 on: December 02, 2012, 05:26:41 PM »

Wow I never would have thought to do that! great idea! I'll practise a bit on an old junk accordion first and perfect the technique before I get my hands on the paolo!! Thanks!

Is there much evidence of the holes afterwards?
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing celluloid
« Reply #15 on: December 02, 2012, 06:00:16 PM »

I'd just add that after filling with mail varnish or celluloid in acetone you need to leave plenty of time before you can effectively sand or polish it.  Several days at least, maybe longer depending on the thickness of fill.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Removing celluloid
« Reply #16 on: December 03, 2012, 02:39:14 AM »

Also wait about 8 hrs between coats of dissolved celluloid, you may get little bubbles that will show when you try to sand or polish it.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing celluloid
« Reply #17 on: December 04, 2012, 12:14:25 PM »

I placed the plate in a shallow dish, poured in enough acetone to cover it, covered the dish and left it to brew.
After several hours the celluloid was as good as the day it was put on in the factory.
The acetone had absolutely zero effect.

In that case either the celluloid was some other polymer, or the acetone wasn't acetone!  Real acetone softens the surface of real celluloid almost instantly, and make it very soft quite quickly, and turns it into a semi liquid in an hour or two.

Presumably you boiled it in water, or we would have read about the musician who set his house on fire.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Removing celluloid
« Reply #18 on: December 04, 2012, 02:14:08 PM »



The acetone was nail polish remover, so you must be correct in saying the celluloid was some other type of plastic stuff.
I had suspected as much.


Did it say that it contained acetone on the bottle?, there are also ethanol-based nail polish removers.
Logged

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Removing celluloid
« Reply #19 on: December 04, 2012, 02:42:12 PM »

Definitely not celluloid then. Was it an old box?. If so then it might have been bakelite, or similar phenolic, which is notably resistant to solvents and pretty durable so more suited to a fingerboard plate.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal