Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Vintage Hohner body repair  (Read 8088 times)

0 Members and 1 Guest are viewing this topic.

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Vintage Hohner body repair
« on: December 27, 2012, 05:39:08 PM »

My old Hohner, having likely had more use in the last 6 months than the previous 80 years, needs some repair to the casing where the old buckram is wearing through. The best way to accomplish this would be to remove the metal corner protectors. These are just pinned in. Can someone who has done this (Theo?) tell me how easy it is to pull the pins out & replace them? The pins protrude (slightly) into the inside of the bellows - if I pull off the corner protectors, I might have an issue with air leaking - I am assuming this could be dealt with with a little dab of glue on the inside of the bellows around the spot where the pin protrudes?

Thank you for any input!
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Vintage Hohner body repair
« Reply #1 on: December 27, 2012, 05:42:12 PM »

On the one I did the pins pulled out reasonably easily. I seem to remember that I pushed them through from the inside and then pulled them with a pair of end cutters.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Vintage Hohner body repair
« Reply #2 on: December 27, 2012, 05:56:25 PM »

I did the same as Lester.  Take care with the corner pieces they can be very brittle so push the pins out from inside to get started, and try to avoid any levering against the metal.   The nails sometimes shed their heads but are easily replaced - Hohner reed plate pins as used on older boxes are a very close match.   If you need some I have loads spare.   Once you have glued on new buckram and replaced corners and pins you should not have air leaks from the pins.  If you do then a dab of wood glue on the inside of the protruding pin will seal it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Vintage Hohner body repair
« Reply #3 on: December 27, 2012, 07:59:20 PM »

In bookbinding I have a very similar problem with what we call "furniture".
   These are all the brass bits found on a Victorian Family Bible, generally  large brass corners, clips and locks,or even a complete brass strip all around the outside boards ( covers). They are almost invariably bent where someone in the past has tried to lever them off. As an aside this stuff is not brass but mild steel brass plated, makes it impossible to polish effectively. Anyway, the little pins that were used WERE brass and as soon as you try to lift them, gently,gently, they snap. Being scientific for a moment, I think the wood shrinks and the brass pins swell. And brass is notorious for metal fatigue. Anyone been there trying to take an old door off when 80 odd years ago the carpenter used brass screws? They snap.
    In actual fact this furniture was generally glued on during the binding process and the pins were there more or less for show. SO, when the pins snap it's quite acceptable to glue the furniture  and place the old pins, now a quarter of their size back in position.
Now come on gang , argue with that!!
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Vintage Hohner body repair
« Reply #4 on: December 27, 2012, 08:05:00 PM »

On old melodeons the pins are usually steel, and the corner pieces are rather thin sheet zinc.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Vintage Hohner body repair
« Reply #5 on: December 27, 2012, 08:19:48 PM »

Thank you Lester & Theo.

My other issue: there is some leaking of air from the corners of the bellows frame where the buckram has worm away. When I fold the buckram back there will (I suppose) need to be a diagonal cut in the buckram to enable it wrap around this this corner. I'm assuming the glue will help provide a seal, even though the buckram will have a little diagonal cut in it?
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Vintage Hohner body repair
« Reply #6 on: December 27, 2012, 08:20:24 PM »

On old melodeons the pins are usually steel, and the corner pieces are rather thin sheet zinc.
Might be so on bibles Theo, but the Brass work seems a bit more substantial.
 Did more expensive Melodeons use stronger or more upmarket material?
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Vintage Hohner body repair
« Reply #7 on: December 27, 2012, 08:23:49 PM »

Check the glued joint between the last fold of the bellows and the frame, it may need to be re-glued.  And cut the buckram to give a slightly bigger overlap onto the bellows. This will cover any line from the old buckram, and give you a bigger gluing area.  You may be able to make a singe cut at the corner and overlap the buckram where it wraps round the corner of the first fold.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Vintage Hohner body repair
« Reply #8 on: December 27, 2012, 08:27:52 PM »

Airtime, I should point out that I am not a repairer of Melodeons, but am in an allied trade when it comes to leather, cardboard and glue.
I wonder why you are saying Buckram. I'm pretty sure Rexine was used as a cover material, sadly no longer made. But there is a similar stuff on the market not as good but more or looks the same.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Vintage Hohner body repair
« Reply #9 on: December 27, 2012, 08:30:05 PM »

Should have said "more or LESS looks the same.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Vintage Hohner body repair
« Reply #10 on: December 28, 2012, 12:01:23 AM »

OK Theo - I'll give it a try.

The buckram is from Charlie Marshall - it seems to be a pretty close match to what's already on there.
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Vintage Hohner body repair
« Reply #11 on: December 28, 2012, 12:38:49 PM »

Thank you Lester & Theo.

My other issue: there is some leaking of air from the corners of the bellows frame where the buckram has worm away. When I fold the buckram back there will (I suppose) need to be a diagonal cut in the buckram to enable it wrap around this this corner. I'm assuming the glue will help provide a seal, even though the buckram will have a little diagonal cut in it?
There should be no need for diagonal cuts in the corners (if you mean what I think you do)
Simply glue the buckram round the outside of the frame, terminating it as far from a corner as possible but  where the join will be hidden under the metal corner piece and leaving the edges standing upright.
Next glue down opposite edges, nipping the corners tight, which will form a 45 degree turn on the ends of the other edges.
Then glue the remaining edges down - if you get enough glue into the overlaps and keep the bellows compressed under weight while drying you should wind up with barely visible flat joints.
http://i467.photobucket.com/albums/rr33/Bruce_almighty_album/bellow/n021.jpghttp://s467.photobucket.com/albums/rr33/Bruce_almighty_album/bellow/?action=view&current=n022.jpg

Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Vintage Hohner body repair
« Reply #12 on: January 06, 2013, 11:51:36 AM »

This thread is most timely, as I will soon need to make a repair on a Hohner Club 1. There are slight air leaks where the buckram is wearing through at the angle between the wooden end and the first fold of the bellows, and especially so at a couple of the corners.

Questions:
1. Should I glue new buckram over the old (which is mostly in good condition apart from the wear spots)?
2. Or should I remove all the old buckram from the ends prior to replacing all of it with new?
3. If the latter, what is the best way of removing the old stuff please?

Thanks,
Steve
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Vintage Hohner body repair
« Reply #13 on: January 06, 2013, 12:35:13 PM »

Definitely remove the old buckram first or you will not get a smooth finish, and the frames will be slightly fatter. 
You may find that it peels off easily with help from a blunt knife slid between buckram and wood.  The original glue will be water soluble, so if there are areas that are tight a light spray of water on the outside of the buckram will soak in and release the join.  The time it take to soak in will vary depending on the condition of the buckram.  If it needs more than 5 or 10 minutes you may need to apply some water, then wrap in polythene or cling film to prevent the water from evaporating.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Vintage Hohner body repair
« Reply #14 on: January 06, 2013, 12:47:16 PM »

You could go for the easy option and just run a strip over the bellow to frame joint (you will need to extend it a bit further over the old stuff onto the bellows)
Presumably a Club will have black buckram so you would not have any colour match problems
If you do the proper job the buckram will be stuck on with animal glue so, although you may be able to tear the bulk of it off, you will have to use hot water to remove the residue, and to part it away from the bellow paper.
This needs to be done with some caution to avoid warping the frames or weakening the glue holding them to the bellows.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Vintage Hohner body repair
« Reply #15 on: January 06, 2013, 01:15:20 PM »

Thanks, Theo and An Bosca Ceoil for your most helpful replies.
My next question is what glue should I use? I had planned on using dilute white PVA, but perhaps I should use something which could be more easily removed at some point in the future. Gum Arabic glue or, if animal glue the cold liquid sort perhaps? (I'm not set up for hot animal glue.)

 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Vintage Hohner body repair
« Reply #16 on: January 06, 2013, 01:31:33 PM »

Fish glue would be a good choice for this.  It is even more easily reversable with water than regular hide glue but very strong.

http://www.conservationresources.com/Main/section_34/section34_18.htm
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Vintage Hohner body repair
« Reply #17 on: January 06, 2013, 02:46:20 PM »

If you must use PVA do not dilute it or you will faff about forever, especially with the returns and corners, you need the "Tacky" stuff.
If you are not bothered about reversability you could do worse than trying Evostick Solvent Free, you can use the "coat both surfaces" method but the buckram may try to curl up while it is tacking off!
"Boiled Horse" is best because it pulls up tight as it dries but  have no idea if the bottled stuff does.
(Funny you should mention Gum Arabic because years ago they used to make Passe Partout (Sp) tape coated with that, primarily for edging glass over pictures. It would probably been just the job for small repairs to damage such as you mention.)
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Vintage Hohner body repair
« Reply #18 on: January 06, 2013, 03:06:30 PM »

Steve, Oh please don't go go down the Bostick route
You'll be into Sellotape next , sorry sticky backed plastic. You are just adding an acidic substance that will play havoc with the reeds. Even Copydex, yuk. Will start rotting within six months.
 If you are not into hot glue, then bookbinders PVA is great . Woodworkers stuff is ok. Paste is the ideal, but as has been said before, you'll be faffing about for ages. If you want more advice PM me, And I'll give you my phone number
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Vintage Hohner body repair
« Reply #19 on: January 06, 2013, 03:38:29 PM »

Once again, thanks chaps for the advice. Don't worry Nick, I won't use bostick or sellotape! I do know better than that.  ;)
I will probably go for the fish glue. When I am ready to do the repair work, I'll update you on my choices and how I get on.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal