Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Treating/varnishing ply wood  (Read 1472 times)

0 Members and 1 Guest are viewing this topic.

EastAnglianTed

  • The wise wearer of the onesie
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 531
  • Castagnari Hascy-East Anglia for the win!
    • My Youtube account
Treating/varnishing ply wood
« on: January 14, 2013, 01:23:04 AM »

    Having stripped celluloid off of my toy melodeon, and faced with bare ply wood, I am a little unsure.
    I'm under no illusion that with ply wood as a base, a Dino-esque finish is never going to be truly attainable, but what should I use to get the closest results to a sexy finish? Thanks
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Treating/varnishing ply wood
« Reply #1 on: January 14, 2013, 07:47:41 AM »

Liberon Finishing oil - it was recommended to me by Rees when I did the 2915 and 114 Retro refurbs and it looks fantastic
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Treating/varnishing ply wood
« Reply #2 on: January 14, 2013, 07:54:15 AM »

    Having stripped celluloid off of my toy melodeon, and faced with bare ply wood, I am a little unsure.
    I'm under no illusion that with ply wood as a base, a Dino-esque finish is never going to be truly attainable, but what should I use to get the closest results to a sexy finish? Thanks
It depends on how much time, energy and money you want to put in to something which is basically of very little value, other than a toy. For example you could replace the celluloid with a nice wood veneer, but personally I don't think I would bother going that far.

My recommendation would be to sand it down as well as you can to get as smooth a finish as possible, then stain the wood with some proprietary wood stain - perhaps dark oak or mahogany colour - then fine sand it down again. Repeat that process a couple of times or so and then finish with a couple of coats of clear polyureathane varnish/lacquer, matte, semi-matte or gloss depending on your personal taste, again fine sanding down between coats.

An alternative to varnish (with or without prior staining) is Liberon Finishing Oil, which is easy to apply (and to reapply at a later date if needed), and gives a nice semi-matte finish. 

Edit - I see Adam-T posted at the same time as me and also recommends Liberon Finishing Oil  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Treating/varnishing ply wood
« Reply #3 on: January 14, 2013, 08:00:55 AM »

An alternative to varnish (with or without prior staining) is Liberon Finishing Oil, which is easy to apply (and to reapply at a later date if needed), and gives a nice semi-matte finish. 

The biggie with Finishing oil is that if you chip, scuff or scrape the box later on, all you do is sand the dent out and re-apply to the area, or just re-apply leaving the chip there for that Pikey look (Sorry Pikey, couldn`t resist  ;D)
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Treating/varnishing ply wood
« Reply #4 on: January 14, 2013, 08:04:03 AM »

Following on from the Liberon Finishing Oil recommendations, here are a couple of pics of my Wesson Clipper. The casework is made of old, reclaimed cherry, which Rees stained with a mahogany woodstain, then rubbed down with LFO. I've had it nearly 4 years now and I've redone the oil once in that time.

It looks (and sounds) wonderful. Thanks again Rees!  (:) (:) (:)

Edit: the colours in the attached photos seem to have lost some saturation in the posting to melnet process. In reality, the box is a richer red colour than what seems to be shown here. 
« Last Edit: January 14, 2013, 08:12:18 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

EastAnglianTed

  • The wise wearer of the onesie
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 531
  • Castagnari Hascy-East Anglia for the win!
    • My Youtube account
Re: Treating/varnishing ply wood
« Reply #5 on: January 14, 2013, 08:48:40 AM »

Im doing up my toy melodeon so's I can have a nice little box to pop in my hand luggage when flying primarily. I have found a stockist near me, so I'm going out to get some dremel bits and some Liberon. Thanks guys, great help! ;)
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Treating/varnishing ply wood
« Reply #6 on: January 14, 2013, 09:57:18 AM »

Stating the obvious here but if it's ply don't get too carried away with the sanding as it's possible to go through to the next layer or even just sanding the ply so it's too thin will give a "patchy' appearance.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal