Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Treble Mechanism Repair  (Read 4566 times)

0 Members and 1 Guest are viewing this topic.

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Treble Mechanism Repair
« on: January 31, 2013, 06:45:28 PM »

Hi,

Hopefully this photo will show what's going on here, two strips that form part of the mechanism and that should be riveted together, have started to come apart.  Strangely this happened while the instrument was sitting, it was perfectly fine last time I played it in October.   



I plan to remove the loose rivets, and replace with small screws and nuts.   Any other suggestions or comments?   All I've done so far is to unhook the springs where the parts are coming apart.  I won't dismantle further until I've got the screws so that I don't leave it in vulnerable pieces for longer than necessary.

Thanks, Tony S
Logged
Tony S

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Treble Mechanism Repair
« Reply #1 on: January 31, 2013, 06:59:49 PM »

Nuts and bolts will be even more likely to come loose.  Better to replace rivets with new rivets.  Before you attempt any repair release all the treble springs which will allow the two strips to lie against each other.

And you will probably find access much easier if you take the whole mechanism out before you start.
« Last Edit: January 31, 2013, 07:01:30 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Treble Mechanism Repair
« Reply #2 on: January 31, 2013, 07:18:32 PM »

Nuts and bolts will be even more likely to come loose.  Better to replace rivets with new rivets.  Before you attempt any repair release all the treble springs which will allow the two strips to lie against each other.

And you will probably find access much easier if you take the whole mechanism out before you start.

Agree with Theo, but if you can't rivet be sure to use loctite/super glue on the nuts and bolts to prevent the coming undone unintentionally.

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Treble Mechanism Repair
« Reply #3 on: January 31, 2013, 07:28:47 PM »

Thanks for both comments.  I was worried about rivets firstly because I don't have them to hand and I'm not sure what to make them from (aluminium?).  Secondly because it means applying some force to close them.  I don't think it will be a problem locking the screws and nuts - the mechanism on my Pokerwork has been fixed to the sound board with screws and nuts for over 20 years.

However I am interested in rivets now - what would you use to make them?  They need to be under 2mm diameter.

The advice to release all the springs first then remove the whole mechanism is good and I will do that whatever repair I carry out.

Tony S
Logged
Tony S

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Treble Mechanism Repair
« Reply #4 on: February 01, 2013, 10:13:01 AM »

If you use nuts & bolts, or set-screws, you could peen the end over to stop it coming undone.
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Treble Mechanism Repair
« Reply #5 on: February 01, 2013, 11:33:05 AM »

If you use nuts & bolts, or set-screws, you could peen the end over to stop it coming undone.

Yes you could, but that would make future dismantling difficult.  A Loctite or similar seal can, by its very design, be if the fastener needs to be undone, while a peened-over screw end would require the screw to be drilled out or the nut to be split or cut off - not an easy task in the small sizes and confined spaces of a melodeon mechanism.  Not impossible, but not easy.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Treble Mechanism Repair
« Reply #6 on: February 01, 2013, 04:54:48 PM »

Nyloc nuts are a reliable choice.
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Treble Mechanism Repair
« Reply #7 on: February 01, 2013, 07:32:30 PM »

Good thinking!
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Treble Mechanism Repair
« Reply #8 on: February 01, 2013, 07:39:32 PM »

Thanks for all the suggestions.  I don't want to open out the existing holes but I think M1.6 screws would be a good fit, and have the advantage of being reversible if I or anyone else wants to replace them with rivets at a later date.   Nyloc nuts would be good, but a quick look at mail order places didn't turn up any smaller than M2.

A couple of the rivets further along are loose so I'll need to give it all a proper inspection when I've got the screws and have the mechanism out on the bench.  It's funny that I didn't notice any sign when I had it all in bits to refinish the pallets around 18 months ago.

Tony S
Logged
Tony S

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Treble Mechanism Repair
« Reply #9 on: February 01, 2013, 07:55:42 PM »

What model of box is it?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Treble Mechanism Repair
« Reply #10 on: February 02, 2013, 09:58:15 AM »

What model of box is it?
It's a Club II.
Logged
Tony S

DaveCottrell

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
Re: Treble Mechanism Repair
« Reply #11 on: February 02, 2013, 05:04:02 PM »

What is the general opinion of pop rivets for this repair? (ie the hollow aluminum ones that use a rivet gun to install)
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Treble Mechanism Repair
« Reply #12 on: February 02, 2013, 05:16:12 PM »

Do you really need to ask? :(
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Treble Mechanism Repair
« Reply #13 on: February 03, 2013, 04:09:44 AM »

Or maybe hot rivetting?

(OK, I won't ask!)
« Last Edit: February 03, 2013, 04:12:05 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Treble Mechanism Repair
« Reply #14 on: February 03, 2013, 09:31:44 AM »

Recommended for PAs, I've heard  >:E

To return to the thread, where would one obtain a supply of preformed rivets of a suitable size (in suitable quantities)?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Treble Mechanism Repair
« Reply #15 on: February 03, 2013, 10:32:40 AM »

To return to the thread, where would one obtain a supply of preformed rivets of a suitable size (in suitable quantities)?

Model engineering suppliers, for example here ... 1/16" Copper Rivets.   Brass and Iron also available.

Suitable tooling as well "Rivet Snap?" (I haven't riveted since school metalwork but if memory serves you need two of these, one to hold the preformed head and one to strike and form the new head closing the joint, and I remember them being called "Dollies" not Snaps).

Or for high class boxes in  ... Solid Silver

By the way, personally I'd be OK with pop rivets if they were available small enough.  I can't find them smaller than 2.4mm.  Aluminium pop rivets would meet my goal of "doing no harm" as they could readily be removed by any future restorer.

Tony S
Logged
Tony S

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Treble Mechanism Repair
« Reply #16 on: February 03, 2013, 10:45:07 AM »

I'm pretty sure that pop rivets would be too weak they are aluminium and hollow after all, and anyway are probably not available in a small enough size.  The originals appear to be steel and they failed, so a weaker material might not last long.  Perhaps nuts and bolts are the answer?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Treble Mechanism Repair
« Reply #17 on: February 03, 2013, 10:59:16 AM »

I'm no expert on riveting, haven't used "proper" rivets for years, but I wonder if the original rivets just weren't fitted properly.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Treble Mechanism Repair
« Reply #18 on: February 03, 2013, 01:08:05 PM »

Nuts and bolts are the way to go plus Locktight.
Karen,my wife and her spectacles are a case in point. The arms were always falling off. And uncannily she always finds the screw ( no, don't go down that road) a small drop of Locktight  does the trick permanently . Don't say that it's impossible to take apart. What are rivets for after all? Apart from cheapness in construction.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Gandy

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 407
Re: Treble Mechanism Repair
« Reply #19 on: February 03, 2013, 02:26:08 PM »

... The originals appear to be steel and they failed, so a weaker material might not last long.

The originals are quite soft, I don't think they're still.  Maybe zinc.   If so then the failure might be from corrosion where they go through the steel strip.  I've just finished dismantling and inspecting and decided to take out all the rivets along that line.  Several had already failed but not yet pulled apart and the others were loose and clearly on their way.   View from behind showing failed and failing rivet ..


The other row, away from the levers on that picture, all seem to be sound.  I am pretty sure that these are in compression and don't hold the action in any case.   End-on view shows the relationship, the bit of copper wire shows where the failed rivets fit holding the action, strip and bracket altogether.  Pressure from the springs puts these in tension.   To the left are the sound rivets.


By the way I thought the objection to pop rivets might have been more philosophical than practical.  I'm beyond the pale already for using hot melt glue to fit the pallets.

Should be a five minute job to get it back together now once I get my hands on some suitable fixings.
Logged
Tony S
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal