Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: cleaning solvent  (Read 7042 times)

0 Members and 1 Guest are viewing this topic.

stillicidia

  • Member
  • *
  • Offline Offline
  • Posts: 26
cleaning solvent
« on: December 15, 2008, 06:07:02 PM »

I've cleaned up the reeds I'm working on by hand so they are fairly clean now - I was going to sit them in an ultrasonic cleaner to remove any minute particles and remaining residue from the wax etc.
I wondered if there might be a preferred solvent that folk use for cleaning up their reeds?
obviously a water based solvent would be out of the question so what is the best thing to use please?
thanks
Richard
Logged
Dyslexic fingers and deaf as a post!
member of accordions anonymous - I admit it I am an accordion addict!
it all started with just one! just a little one! then another, and another...

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: cleaning solvent
« Reply #1 on: December 15, 2008, 06:40:41 PM »

White spirit will dissolve wax and most adhesive residues.
"Fiercer" solvents such as acetone and ethanols, apart from being hazarous, will degrease the steel so much that it will be suceptible to rust once the air hits it.
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: cleaning solvent
« Reply #2 on: December 15, 2008, 08:53:29 PM »

Isn't it better to leave some kind of protective "residue" on the reeds, like a very thin film of oil?
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Aaro

  • Good talker
  • **
  • Offline Offline
  • Posts: 78
    • Luukinen Accordions
Re: cleaning solvent
« Reply #3 on: December 15, 2008, 09:36:06 PM »

Hi

I am a clean-up the reeds plates of acetone or denatured alcohol.
Although this sounds crazy
Reeds plates is possible to boil the water if reeds plate is a very dirt    
or does not want to use acetone or a similar substance. Reeds does not stain if dry immediately.


Aaro
« Last Edit: December 15, 2008, 09:48:10 PM by Aaro »
Logged
Luukinen Accordions offers a full line of fine handcrafted custom made accordions.

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: cleaning solvent
« Reply #4 on: December 15, 2008, 10:18:57 PM »

Isn't it better to leave some kind of protective "residue" on the reeds, like a very thin film of oil?

That is why I said white spirit, because I think it does leave a very slight residue.
(Water will bounce off anything that has been pre cleaned with kerosene)
In the past I have tried things like acetone and methanol but, although they work faster, I would not recommend them because  they are too volatile for safe "home" use.
I have tried boiling them (lots of people used this method) but it seemed to reveal a lot of misaligned tongues.
Might have be coincidence but made me wonder if heating them unduly tended to temporarily loosen the rivet.
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #5 on: December 15, 2008, 10:27:24 PM »

The preferred medium for ultrasonic cleaners is water, since it cavitates very strongly.

Corrosion is not a problem if you dip in a de-watering oil and it does not leave a  big rsidue.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cleaning solvent
« Reply #6 on: December 15, 2008, 10:28:13 PM »

I've never found it necessary to use any sort of solvent.  I scrape of the worst from the reedplate with an old blunt knife, then brush with a soft stainless steel wire brush.  Tongues I clean with a combination of sanding "pens" wet and dry abrasive paper, and a pcb polishing block.  The fibreglass pencil can be handy too, but the dust is irritating to the nose and throat so I avoid using it if I can.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cleaning solvent
« Reply #7 on: December 15, 2008, 10:28:49 PM »

The preferred medium for ultrasonic cleaners is water, since it cavitates very strongly.

Corrosion is not a problem if you dip in a de-watering oil and it does not leave a  big rsidue.

Do you have experience of using this on reeds?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #8 on: December 16, 2008, 09:20:04 AM »

Regrettably not, but the high strength aerospace alloys I do have experience with are VERY corrosion sensitive.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cleaning solvent
« Reply #9 on: December 16, 2008, 09:38:03 AM »

Sounds interesting, I have a few more questions. Does the material leave the surface dry?  Any experience with mixed metal components eg aluminium/steel, dural/steel, brass/steel?  I am interested in developing a reliable method of ultrasonic cleaning for reedplates, but up till now I've been put off by the possible corrosion problems if the metal surface is left too clean.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: cleaning solvent
« Reply #10 on: December 16, 2008, 11:38:11 AM »

When the subject of using solvents was raised, I assumed that it was to clean off any remaining debris after the manual cleaning methods that you mentioned earlier.
Presumably that is all that an ultrasonic cleaner would do, or would it tacle rust given enough time?
Logged

stillicidia

  • Member
  • *
  • Offline Offline
  • Posts: 26
Re: cleaning solvent
« Reply #11 on: December 16, 2008, 04:48:41 PM »

an ultrasonic cleaner is excellent on small brass bits from carburettors and the like and I use it to clean out the jets - the bits you cant get at! - thats why I thought it would be good to use on the reeds after manual cleaning - I do use water for cleaning up the jets but I thought that would be a problem for the reeds - I was thinking about using meths or acetone as a solvent but if that is going to leave the reeds too grease free then that might well be a problem. I just thought that the process would remove any minute bits stuck between the reed and reed plate that may not even be visible - pedantic perhaps but I'm not intending to do the job more than once so wanted to do my best. I read about cleaning reeds on a website from America but there the solvent used was Benzene - thats fairly nasty carcinogenic stuff so I wondered if others used something else - hence the question. I thought the idea of dipping in an anti watering oil would be unacceptable because of the deposits left - am I wrong in this assumption?
Thanks for all the usefull help with my questions by the way - really appreciated. ::)
Logged
Dyslexic fingers and deaf as a post!
member of accordions anonymous - I admit it I am an accordion addict!
it all started with just one! just a little one! then another, and another...

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #12 on: December 16, 2008, 08:18:19 PM »

Depends on the de-watering oil you use I suppose.  De-waterers start like WD40 (Plusgas etc).  They carry a light wax in a volatile solvent.  The wax/solvent drive out the water and then leave a very thin wax on the surface to prevent further rust.

Water works best as an ultrasonic medium because it cavitates very effectively.  This means that micro-bubbles burst on the surface and remove the debris there.

You can use other solvents.  beware of highly flammable ones like meths or acetone.  Ultrasonic cleaners are electrically powered and can generate sparks.  You would not like an acetone fire!

Try white spirit, I suppose, if you are worried about corrosion.  I would not be, provided you use a decent de-waterer.
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: cleaning solvent
« Reply #13 on: December 16, 2008, 11:44:20 PM »

I seem to remember the use of WD40 being discussed before, with some people rubbishing the idea.
For a change I am with you on this one, because I think the amount of residue would be insignificant.
Looking at the blue side of some old reed tongues the accumulated dirt seems to have adhered to a once oily surface. Presumably that got there during the grinding or was on the steel when it arrived from the producer.
I appreciate that an ultrasonic cleaner could  be used with water, ideally with added surfactant/wetting agent, to remove  surface grime. If however you were looking to remove rust the additives appear to be phosphoric acid solutions - does this not attack aluminium?
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #14 on: December 17, 2008, 12:39:54 AM »

I would not recommend the phosphoric acid preparations in this circumstance. The mode of operation is convert Iron oxide (hydrated) to iron phosphate.  This is fine for car bodywork and the like, but you have to remember that to get proper corrosion protection you are meant to paint the surface otherwise it converts back in time.  I can see this really mucking up tuning.

Has anyone experimented with stainless steel reeds.  (Note that "stainless" is probably the biggest contravention of the Trades Description Act ever).  There are passivation processes which generate a self-sealing corrosion resistant coating on the surface of the metal.

BTW, just because my position on EFDSS and preserved dance is akin to Attila the Hun's does not make me an unreasonable person - honest  ;D
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: cleaning solvent
« Reply #15 on: December 17, 2008, 01:14:08 AM »

Quote
The mode of operation is convert Iron oxide (hydrated) to iron phosphate.  This is fine for car bodywork and the like, but you have to remember that to get proper corrosion protection you are meant to paint the surface otherwise it converts back in time.  I can see this really mucking up tuning.

Which - the phosphate or the coat of paint? :D

Quote
BTW, just because my position on EFDSS and preserved dance is akin to Attila the Hun's does not make me an unreasonable person - honest

Would not deny anyones entitlement to their own opinions!
I was referring to your notion about pumping wax through a glue gun - crossed my mind to try it just to prove you wrong but it is too cold out there.
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #16 on: December 17, 2008, 10:41:17 AM »


Which - the phosphate or the coat of paint? :D


Both :D:D
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: cleaning solvent
« Reply #17 on: December 17, 2008, 10:57:35 AM »

Let's face it.  Nothing removes rust except an abrasive.  Why would you want to convert it to something else by chemical means if you don't regain the near pristine steel surface which was the aim of the reed maker in the first place?  Scrape 'em off and then you can clean them with something pretty neutral.  We used to clean all manner of things in a large industrial ultrasonic bath , using a Decon detergent in a beaker in a water bath.  If you left a bicycle chain in for long enough, it got all the grit and grease out and got quite hot.  It was so degreased that it would rust within minutes of coming out, so you would have a bath of molten chain grease ready to receive it.  Other items would be sprayed with WD40 and slapped into a plastic bag until ready for the next process, whatever that may have been. 

I believe that the basis of WD40 and other dewatering oils is lanolin in a paraffin carrier.  If that is correct, then if left to air dry, only something slightly more than a monolayer of protective film will be left behind.  Either way, by the time you've retuned it, the reed will have been handled and wiped and scratched...

Rob.
Logged

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: cleaning solvent
« Reply #18 on: December 18, 2008, 08:43:40 AM »

 re: " Nothing removes rust except an abrasive.  "

immersion of rusty steel in molasses (thinned with water) will remove the rust.
leave the reed in this solution for a week should remove all deposits.
pliers from the shed may take a month.....

Jack
Logged
Jack Murphy    beyond the black stump

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: cleaning solvent
« Reply #19 on: December 18, 2008, 11:44:18 AM »

Actually, don't laugh, coca cola contains phosphoric and citric acids (ask any dentist).  It WILL remove patina from copper coin, though I have never tried it with surface iron oxide deposits.  It would be unlikely to leave a phosphate residue.

Obviously, thorough cleaning after the event would be essential.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal