Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: sticking key again  (Read 6187 times)

0 Members and 1 Guest are viewing this topic.

bobk

  • New Starter
  • Offline Offline
  • Posts: 2
sticking key again
« on: December 15, 2008, 09:22:04 PM »

I have just been reading an old topic on a sticking button on a serenellini 213. This problem has just started for me on an instrument that is a few years old. The button in question is the G/A button on the G row of a G/D instrument.

I have contacted serenellini who have suggested removing, very carefully, the pin that goes through the keyboard (holding the levers and springs in place I guess) and sandpapering the lever. I am wary of this! Will I get springs firing everywhere? Like a previous contributor, I have found that the keyboard is glued as well as screwed to the 'other bit'. I see someone says that the glue might weaken if damped.

Any comments welcome!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticking key again
« Reply #1 on: December 15, 2008, 10:20:51 PM »

It can be tricky pulling out the axle rod, it may be tight, and often there is only a short length to get hold of, you also have to hold the keyboard securely without forcing anything, and be able to restrain the levers from springing out as the rod is withdrawn. If you have a sticky lever then first of all try some dry lubricant down the sides of the lever.  Whatever you do, do not use, oil, WD40, or any liquid that will soak into the wood and leave a reside.  Powdered graphite is the best thing to try.  Or you can make your own from the core of a 4B or softer pencil.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

BruceHenderson

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 262
Re: sticking key again
« Reply #2 on: December 15, 2008, 10:47:52 PM »

(snip) Whatever you do, do not use, oil, WD40, or any liquid that will soak into the wood and leave a reside. 

    Any kind of oil or liquid will also attract dust and dirt, turning into "oil based mud".  Theo is right - it doesn't belong in the mechanism of a melodeon.

Powdered graphite is the best thing to try.  Or you can make your own from the core of a 4B or softer pencil.

    I've never had any luck with graphite, etc.  One of my Beltuna's stuck a couple of levers pretty tight after being in a US summer for a while.  I pulled the rod.  First, make a note of the sticking key(s).  Then, when you pull about 1 1/2" out, the first key will come loose; lay that one out so the the spring is kept in position and mark the side "closest" to your chin with the number 1.  Pull the rod another 1/2" or so and remove the second key; mark the number and lay it out in order.  Repeat until you have all the keys you want out - there will probably be 3-4 or more that you don't have to remove.  Lay the sticking key on a flat table or work bench.  Wrap fine sandpaper around a flat blade (putty knife, wide blunt-edge scraper, etc.) and rub the side of the key gently at the pivot area.  Don't let the sandpaper and its tool rock -- you want to keep the angle against the key flat, but that's pretty easy.  You may need to sand both sides of the key pivot area but that's easy.  Then just reassemble it.

   Go slowly, be methodical, and sand gently.  About the only real problem you can have is if the rod is too tight to pull out easily.  What might help would be to grab the little tang on the end of the rod (there's sometimes a little cover cap that you have to remove a screw to get off) with a pair of pliers.  If necessary, you can put a little piece of soft leather around the pivot rod -- be sure you don't scratch or raise burrs on the rod, if you do, it will jam when you try to put it back in.  But it's usually really easy.  Just don't force anything.  (I have a repairman friend who says that he connect a car battery to each end of the rod is it's really stuck -- the rod will get hot and release the grip of the wood; you won't have to go to THAT kind of lengths!)
Logged
I love one-rows!  Four reeds kick butt!!!!

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: sticking key again
« Reply #3 on: December 15, 2008, 11:51:19 PM »

 Bruce,
Agree with most of what you say but would have used "sometimes" rather than "usually" easy to get the rod out -  but perhaps I am not so lucky!
A drill chuck or pin vice can sometimes be more effective than pliers but, if the rod will not start easily, best bet is to send it to Theo and let him hold his breath.
Liked the "element"ary idea about using a car battery but raises the point that, if the other end of the rod is accessible, you can follow the rod through with another one and only have to drop the faulty key out.
Regards,
 Bruce Senior
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: sticking key again
« Reply #4 on: December 16, 2008, 12:00:39 AM »

you can follow the rod through with another one and only have to drop the faulty key out.
Nifty!  ;)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticking key again
« Reply #5 on: December 16, 2008, 12:18:15 AM »

Liked the "element"ary idea about using a car battery but raises the point that, if the other end of the rod is accessible, you can follow the rod through with another one and only have to drop the faulty key out.
Regards,
 Bruce Senior

Usually the "other" end of the rod is not accessible, but its sometimes wise to drill a small neat hole for the purpose.  Not only can the second rod keep the keys in place, but it can also be used to push the axle rod out far enough to get a good grip on the pulling end.

The car battery idea is highly dangerous, you could get badly burned, so could your instrument.  Car batteries are designed to put several hundred amps into a low resistance circuit, enough to melt small quantities of metal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

BruceHenderson

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 262
Re: sticking key again
« Reply #6 on: December 16, 2008, 05:39:33 AM »

(snip) The car battery idea is highly dangerous, you could get badly burned, so could your instrument.  Car batteries are designed to put several hundred amps into a low resistance circuit, enough to melt small quantities of metal. 

   Oh, yes, I only brought up the issue as extreme.  I'd never do it and I always advise anyone against doing it -- in fact, I'd advise him not to do it but he's been doing it occasionally for 25 years and he wouldn't listen to anything I said anyway.  He thinks that it works but I'm sure that he never lets the metal rod get hot enough to char the wood.

   And my Beltuna was only about a year old ... my guess is that if you have 10 melodeons that are a year-old and 10 that are 20-years-old, a higher percentage of the older ones will have hard-to-remove pivot rods.  But mine came out easy.
Logged
I love one-rows!  Four reeds kick butt!!!!

bobk

  • New Starter
  • Offline Offline
  • Posts: 2
Re: sticking key again
« Reply #7 on: December 16, 2008, 10:19:44 AM »

Thanks for all the comments, I will mentally prepare myself for a go at this in a couple of days. B4 I do would a razor blade down the side of the lever be a good idea, if it fits? \Maybe silly idea? Just trying to avoid dismantling the keyboard.
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: sticking key again
« Reply #8 on: December 16, 2008, 10:26:53 AM »

Doubtful, simply because if there is clearance for a blade the key should not be sticking. If the key is tight on the rod you will achieve nothing, nor will you be able to get at the sides of the key below the rod.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticking key again
« Reply #9 on: December 16, 2008, 10:58:10 AM »

Thanks for all the comments, I will mentally prepare myself for a go at this in a couple of days. B4 I do would a razor blade down the side of the lever be a good idea, if it fits? \Maybe silly idea? Just trying to avoid dismantling the keyboard.

I agree with Shy Talk, but some graphite down the side would be worth trying, even thought its not guaranteed to work, its a lot quicker, simpler and less stressful than stripping the keyboard. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: sticking key again
« Reply #10 on: December 16, 2008, 11:22:23 AM »

Quote
Car batteries are designed to put several hundred amps into a low resistance circuit, enough to melt small quantities of metal.
Do not think the first bit is absolutely true - capable yes -but only in the case of the starter motor.
Enough to melt metal - definitely! We used to cast new terminals onto batteries by shorting an electrode across them!
Sorry if I appeared to advocate use of the somewhat extreme method mentioned which might be practical, but only with a partially charged battery. I imagine that if you tried it with a good one you would simply blow the end off of the rod.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: sticking key again
« Reply #11 on: December 16, 2008, 12:31:03 PM »

I had a couple of keys stick on a Castagnari Nik, attributed to playing in the cold and rain for Morris.  The lever had grown in length due to the moisture and I had to sand a surprising amount off the end to stop it snagging the edge of the keyboard recess.  When you think about it, there is no need for a snug fit there!  I also rubbed all the wood surfaces with a candle, remembering this was commonly done to prevent drawers from sticking.  I'm not claiming this as a cure-all, just comparing notes, but nothing ever stuck again.

Rob.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: sticking key again
« Reply #12 on: December 16, 2008, 01:13:14 PM »

Thanks for all the comments, I will mentally prepare myself for a go at this in a couple of days. B4 I do would a razor blade down the side of the lever be a good idea, if it fits? \Maybe silly idea? Just trying to avoid dismantling the keyboard.

I agree with Shy Talk, but some graphite down the side would be worth trying, even thought its not guaranteed to work, its a lot quicker, simpler and less stressful than stripping the keyboard. 

It might not be the sides of the lever binding at all, I've had problems in the past with my Oakwood with the levers binding on the pivot rod, especially in very hot weather. This appears to be partly caused by dust (maybe some of this is worn-away wood dust) getting into the small gap, the levers are a pretty tight fit on the pivot rod.

I fixed this -- for several years, at least -- by taking out the pivot rod and all the keys, cleaning the rod with a green plastic pan scrubber (not metal, this will scratch the rod and make things worse in future), and cleaning out the holes in the levers with a piece of rough string.

Ian

P.S. All this is a lot easier because the entire keyboard together with the action can be detached by removing two big internal screws, which takes all the tension off the springs -- a nice bit of repairman-oriented design by Oakwood.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

BruceHenderson

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 262
Re: sticking key again
« Reply #13 on: December 16, 2008, 05:09:21 PM »

Doubtful, simply because if there is clearance for a blade the key should not be sticking.  (snip)

   Ditto!!!  Also, if you're taking material off the key, that removed material must go someplace and -- if the clearances are tight enough to make it stick -- then you've got wood powder or granulated paint (my Beltuna has something like a wood sealer, not paint, on the sides of the keys) in the clearance between the key and its slot.
   I also agree with Ian and Rob that the problem might not be in the clearance between the sides of the key and the slot (although I think it's a good chance).  Look for shiny spots on the key when you get it out.  They may give you an indication where the sticky spot is occuring and where you need to remove material.  And Ian's point about polishing the metal surface of the rod is a good one, too.
Logged
I love one-rows!  Four reeds kick butt!!!!

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: sticking key again
« Reply #14 on: December 17, 2008, 12:41:20 AM »

Lot to be said for metal actions :)
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: sticking key again
« Reply #15 on: December 17, 2008, 02:08:02 AM »

Why is it that only expensive italian boxes get sticky keys ???
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: sticking key again
« Reply #16 on: December 17, 2008, 10:14:06 AM »

Why do only expensive (Italian) boxes...?

Because the pressed steel clackety actions of Saxon built machines(God bless 'em) can rust in the bottom of a pond for a decade without seizing!  It's normally the open wooden actions that stick due to inclement conditions.  If you make them slack enough to work in all conditions, then they lose the smooth, even and speedy response that a craftsman can offer.  So - why do I play Italian indoors and a Pokerwork outdoors?  It's a no-brainer...

Rob.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: sticking key again
« Reply #17 on: December 17, 2008, 05:02:28 PM »

Why is it that only expensive italian boxes get sticky keys ???

And Oakwood (English)...

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticking key again
« Reply #18 on: December 17, 2008, 05:13:27 PM »

... pressed steel clackety actions of Saxon built machines(God bless 'em) can rust in the bottom of a pond for a decade without seizing!  It's normally the open wooden actions that stick due to inclement conditions. 

Nearly all the Saxony (Galotta, Weltmeister etc) built boxes have wooden action which does sometimes suffer sticky levers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: sticking key again
« Reply #19 on: December 17, 2008, 05:28:42 PM »

Because the pressed steel clackety actions of Saxon built machines(God bless 'em)...

Metal actions do not have to be clackety.  It depends on how they are bushed and limited.

A Hohner Club is an entirely different animal from an Erica for example,
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal