Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: .  (Read 5726 times)

0 Members and 1 Guest are viewing this topic.

aradru

  • Member
  • *
  • Offline Offline
  • Posts: 42
.
« on: February 13, 2013, 02:30:26 AM »

.
« Last Edit: October 13, 2015, 01:13:40 AM by . »
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Running out of air. Is it a reed setting problem?
« Reply #1 on: February 13, 2013, 11:34:31 AM »

If the reeds were set with too big a gap, I'd expect that trying to play quietly would produce no sound at all (and leak air) while playing hard would produce normal volumes of sound.
Setting too close would make the reed responsive and less leaky at low pressures, but liable to choke when played hard.

If the reeds are on blocks, are the blocks sealing properly to the palette board? (could have warped)
Are the reed plates waxed/pinned in properly?
Leaking coupler slide?
Maybe they just aren't very good reeds...

Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Running out of air. Is it a reed setting problem?
« Reply #2 on: February 13, 2013, 11:40:55 AM »

I think the clue might be in the fact that it's a 4 voice. What's it like if you block off two of the reed sets?
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #3 on: February 13, 2013, 12:28:43 PM »

Anahata suggests leaks under reed blocks.  I'd say that is a strong possibility.  Warped foundation boards are very common on old boxes.  To check, first lift out the blocks and look at the gasket underneath. A telltale sign is if there is a dark dust stain on the gasket showing air has been escaping for years.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: Running out of air. Is it a reed setting problem?
« Reply #4 on: February 13, 2013, 12:46:02 PM »

I have a similar issue with my one-row 4-stop. When all the reed voices are stopped out, if I try to move the bellows nothing happens but if I push a button down some of the keys and move the bellows they move and I can hear air coming through. This made me think it had nothing to do with the bellows and something to do with the reeds. It's a chinese made instrument and I know the quality will never be anything all that great.

I was wondering it might be the same problem though. Something to do with the reedblocks not being set tightly. Is there anything I can do to try and fix this? I brought it to an accordion shop but the guy said it would cost $25 for him to open it up and look at it and he couldn't guarantee being able to make it any better. If reedblock or foundation board we warped would it be too much trouble to sand it flat again?
Logged
Sean McGinnis
Bordentown City, NJ, USA

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Running out of air. Is it a reed setting problem?
« Reply #5 on: February 13, 2013, 01:25:28 PM »

Anahata suggests leaks under reed blocks.  I'd say that is a strong possibility.  Warped foundation boards are very common on old boxes.  To check, first lift out the blocks and look at the gasket underneath. A telltale sign is if there is a dark dust stain on the gasket showing air has been escaping for years.

That was exactly the problem with my old Hohner Club, although it was the blocks themselves that were deformed,; standing them on a sheet of plate glass revealed a noticeable gap in the centre.  I remedied it by gluing a thin piece of lime (aka linden) on to the base and resurfacing it dead flat on a belt sander before re-opening the airholes. Worked like a charm - air loss problems vanished overnight (well, over the three or fours days the job took, off and on!).

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Running out of air. Is it a reed setting problem?
« Reply #6 on: February 13, 2013, 01:29:19 PM »

Anahata suggests leaks under reed blocks.  I'd say that is a strong possibility.  Warped foundation boards are very common on old boxes.  To check, first lift out the blocks and look at the gasket underneath. A telltale sign is if there is a dark dust stain on the gasket showing air has been escaping for years.

That was exactly the problem with my old Hohner Club, although it was the blocks themselves that were deformed,; standing them on a sheet of plate glass revealed a noticeable gap in the centre.  I remedied it by gluing a thin piece of lime (aka linden) on to the base and resurfacing it dead flat on a belt sander before re-opening the airholes. Worked like a charm - air loss problems vanished overnight (well, over the three or fours days the job took, off and on!).

Graham

A simpler method, that I use, is to flat off the existing block base using 120 grit on a sheet of plate glass, then build up the tongue that locates the one end and if needed the block at the other to ensure it is held down in the box.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Running out of air. Is it a reed setting problem?
« Reply #7 on: February 13, 2013, 01:56:28 PM »

I have a similar issue with my one-row 4-stop. When all the reed voices are stopped out, if I try to move the bellows nothing happens but if I push a button down some of the keys and move the bellows they move and I can hear air coming through. This made me think it had nothing to do with the bellows and something to do with the reeds. It's a chinese made instrument and I know the quality will never be anything all that great.

I was wondering it might be the same problem though. Something to do with the reedblocks not being set tightly. Is there anything I can do to try and fix this? I brought it to an accordion shop but the guy said it would cost $25 for him to open it up and look at it and he couldn't guarantee being able to make it any better. If reedblock or foundation board we warped would it be too much trouble to sand it flat again?
With a one-row four-stop, another thing to check is whether the slider ports are completely closed when the stops are pushed in (or out) to stop the reeds from sounding. It is my experience with some Cajun boxes (including those from a highly respected maker) that they have been designed to be played with all four voices going and the port spacing on the sliders allows for this.

However, when the stops are pushed in to stop the sound, there is sometimes still some overlap on the slider ports with the reed chamber port, so some air leakage can occur. This can happen when the gap between the slider ports is not quite the same as the width of the port opening itself. The slider ports and the reed chamber ports line up when the stop is in the open position, but when in the closed position there is still a small gap allowing air into the reed chamber, maybe not enough to make the reed sound, but still enough to lose some air.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Running out of air. Is it a reed setting problem?
« Reply #8 on: February 13, 2013, 02:41:24 PM »

Anahata suggests leaks under reed blocks.  I'd say that is a strong possibility.  Warped foundation boards are very common on old boxes.  To check, first lift out the blocks and look at the gasket underneath. A telltale sign is if there is a dark dust stain on the gasket showing air has been escaping for years.

That was exactly the problem with my old Hohner Club, although it was the blocks themselves that were deformed,; standing them on a sheet of plate glass revealed a noticeable gap in the centre.  I remedied it by gluing a thin piece of lime (aka linden) on to the base and resurfacing it dead flat on a belt sander before re-opening the airholes. Worked like a charm - air loss problems vanished overnight (well, over the three or fours days the job took, off and on!).

Graham

A simpler method, that I use, is to flat off the existing block base using 120 grit on a sheet of plate glass, then build up the tongue that locates the one end and if needed the block at the other to ensure it is held down in the box.

An equally valid way of doing it, but you do end up with a slightly thinner reedblock base (if I understand correctly you compensate for this by adding thickness to the tops of the locating tongue and block). Whatever floats your boat....

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #9 on: February 13, 2013, 03:58:55 PM »


Many thanks for all the replies.
I am almost 100% certain that there are no leaks or warping.
The sound board is metal.
I think the reeds are not bad.
The box is very solidly built.
As I said, bellows compression is excellent and everything seems tight as a drum.

I've just seen a box with a metal base board where there was leakage under the reed blocks, because the blocks were not quite flat.
Leakage from this area only takes place when playing.  With all pallets closed the air cant escape.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #10 on: February 13, 2013, 05:06:53 PM »

With just one reed block fitted, see if you can slide a feeler gauge under the block at various points along its length.  In the absence of a feeler gauge a thin sheet of card, or plastic will do, eg a strip cut out of a plastic milk bottle.  Ideally it should not be possible to get anything to fit easily between block and base board.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Running out of air. Is it a reed setting problem?
« Reply #11 on: February 14, 2013, 05:37:29 AM »

When I did the job on my Club blocks the reeds were out as I was also making some changes to the layout, so I was able to attach and thickness the new base and then open out the airholes from the inside, which is not an option if you're doing it with the reeds still in place. I'd guess a paper template is the way to go - light fingertip pressure will locate the airholes accurately. Theoretically you should be able to measure the airhole diameter, button spacing, row spacing and row offset and draw up a template, but for practical purposes, especially if it's job you're only going to do once, I think I'd go for the paper pattern taken directly form the existing blocks.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #12 on: February 14, 2013, 08:04:15 AM »

As Graham says,  stick on the felt first, then when glue is completely dry feel the holes and cut with a scalpel blade, using the hole in the block to guide the blade.
This method does have the disadvantage of introducing more soft material between the reedblock and the outside world, and could in itself have a deadening effect on the sound.   Sanding the base flat, with additional wood added if needed is a better method.  If you use a thin sheet eg of veneer, then after sanding you can use the same method to re-cut the holes with a scalpel.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #13 on: February 14, 2013, 12:44:26 PM »

thin film of pva applied to the wood only.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Running out of air. Is it a reed setting problem?
« Reply #14 on: February 14, 2013, 02:47:13 PM »

Don't worry about dust, it will all blow out very easily. And it's is generally too fine to stick in reed gaps.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Running out of air. Is it a reed setting problem?
« Reply #15 on: February 14, 2013, 04:57:00 PM »

Hi Aradru, I'm personally not so sure felt is the best medium if you go that route, good quality shamy leather would be my choice along with the correcting of the curvature with sanding on plate glass, and that would depend on the degree to which it is out. I'd also be very carefull to ensure none of the distortion is in the "Sound Board" Ally can easily be changed in shape and tends to maintain any alterations completely having no spring in it, as I'm sure your aware, so I would be out to exclude that from the overall picture before doing anything, hope it all goes well. All the Best mory
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Running out of air. Is it a reed setting problem?
« Reply #16 on: February 14, 2013, 10:28:27 PM »

I have to say I'd not go the felt route either; I'd far rather true up the blocks so that I KNOW they're perfectly flat. Felt might well work, but personally I'd rather do a "proper job".  Mind you, that's just me (bearing in mind I have the workshop facilities to do it), and, as always, I'm perfectly happy to be proved wrong........

Best of luck whichever way you choose

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: Running out of air. Is it a reed setting problem?
« Reply #17 on: February 16, 2013, 02:54:02 PM »

I have a similar issue with my one-row 4-stop. When all the reed voices are stopped out, if I try to move the bellows nothing happens but if I push a button down some of the keys and move the bellows they move and I can hear air coming through. This made me think it had nothing to do with the bellows and something to do with the reeds. It's a chinese made instrument and I know the quality will never be anything all that great.

I was wondering it might be the same problem though. Something to do with the reedblocks not being set tightly. Is there anything I can do to try and fix this? I brought it to an accordion shop but the guy said it would cost $25 for him to open it up and look at it and he couldn't guarantee being able to make it any better. If reedblock or foundation board we warped would it be too much trouble to sand it flat again?
With a one-row four-stop, another thing to check is whether the slider ports are completely closed when the stops are pushed in (or out) to stop the reeds from sounding. It is my experience with some Cajun boxes (including those from a highly respected maker) that they have been designed to be played with all four voices going and the port spacing on the sliders allows for this.

However, when the stops are pushed in to stop the sound, there is sometimes still some overlap on the slider ports with the reed chamber port, so some air leakage can occur. This can happen when the gap between the slider ports is not quite the same as the width of the port opening itself. The slider ports and the reed chamber ports line up when the stop is in the open position, but when in the closed position there is still a small gap allowing air into the reed chamber, maybe not enough to make the reed sound, but still enough to lose some air.

Well I'm glad I didn't pay the $25 to have the repairman open up my melodeon. When I finally got a chance to open it I noticed that the reed block actually was wobbling around because it was that looses...

I tightened it up and 5 min later it is playing both louder and less breathy. Lesson Learned: Check the simplest solution first before thinking about sanding away at the reed block.
Logged
Sean McGinnis
Bordentown City, NJ, USA

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Running out of air. Is it a reed setting problem?
« Reply #18 on: February 16, 2013, 03:15:44 PM »

Dead right - by the same token, if there IS a problem, put it right properly rather than with a quick fix.  ;)

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

BCC#er

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 196
  • Old Hohners rule!
Re: Running out of air. Is it a reed setting problem?
« Reply #19 on: May 01, 2013, 03:02:56 PM »

Hi!

I've met the similar problem. I've got two identical Pokerworks in GC and DG. DG takes noticably more air and I tested the reed blocks as described in this thread. First I found a couple of tiny lumps of wax on one of the reed blocks surface that contacts sound board. It became better without them but still not ideal. So I found the noticable gap between the blocks and soundboard mostly in the central part. And the borders of the leakage are differernt for each block. So what is the best way to fix it? The blocks are perfectly flat so it means the soundboard is not. I can try to use the sandpaper on it but it curves unevenly.

Thanks in advance,
Anatoly
Logged
Several Hohners and B. Gaillard B/C
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal