Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bodged bass and busted bellows  (Read 1880 times)

0 Members and 1 Guest are viewing this topic.

Wulfrun

  • Member
  • *
  • Offline Offline
  • Posts: 5
Bodged bass and busted bellows
« on: April 15, 2013, 05:28:22 PM »

I recently acquired a Hohner club 1b which is in need of some major tlc – not least of all major cleaning to remove decades of dust, accumulated tobacco staining and the odd bit of rust. Upon opening the bass end I was greeted by the sight of a bodge on the third button down of the outer row (tonic chord?) - I've tried to attach a picture, hopefully its worked.

It replaces a broken spring by using the spring loaded mechanism usually found on ID/ visitors badges connected to a bit of bent wire (possibly from a coathanger?) slotted through the hole next to the 'bit of the mechanism that should hold the spring in place' (is there a technical term?) so that when the button is depressed, the rod and wire push down on the ID mechanism and cause the pallet to open. Unfortunately the wire is restricting the movement of the adjacent pallet (inside row second button down, bass?) which has caused the rods to bend and made the action of both buttons more clacky and clunky than one would usually expect from the mechanism!

The options are leave it as is and cope with the restricted movement and bending of rods, replace the spring, or, given the level of rusting present I’m wondering if it would be better to replace the whole bass mechanism?

The instrument is in need of an overhaul anyway, I assume its been left somewhere damp at some point as there is some corrosion/ oxidation on the reed plates, the leather valves have curled, and the wax is filthy and crumbling in places and the bellows are more than a little worse for wear with dodgy taping and the copper in most of the bellows corners having oxidised out to make them a rather fetching shade of green.

The bellows were just about airtight until I removed the combination of parcel tape and electrical tape that was holding them together (on the back as can be expected), and by the fourth big split I gave up trying to be too careful about not damaging the bellows paper as it became pretty obvious I’ll be needing some new bellows. I’m considering a temporary fix reinforcing the interior with card and using washi tape as bellows tape until I find a suitable replacement – it seems daft to go the whole hog with proper bellows tape when they are so decrepit anyway.

Any sensible advice is much appreciated as this is my first attempt at fixing up an instrument.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bodged bass and busted bellows
« Reply #1 on: April 15, 2013, 06:48:12 PM »

Before investing time and money give all the woodwork a thorough examination looking for damage from damp, either rot, or more likely glued joints that have failed.  Also examine the bellows and work out where the air is leaking from, and if it looks repairable.  You need a sound wooden case, and bellows if the project is to be worthwhile. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Roche

  • Guest
Re: Bodged bass and busted bellows
« Reply #2 on: April 16, 2013, 01:49:35 PM »

I find it rather amusing and strangely fascinating that someone had the ingenuity and manual skills to MacGyver up something as convoluted as that spring clip thing yet it didn't occur to them to just make a replacement spring from a bit of wire or repurpose a similar spring from something else...  ;D

The level of rust on that mechanism is nothing major and should clean up relatively easily. It's also made of much sturdier metal than the new ones so it's definitely worth putting in the effort to clean it up. There aren't that many old Hohners that are truly beyond redemption but whether or not you think it'll be worthwhile depends on how much money and work you're willing to put in and if you want to save/make money or if you're doing it for fun or as a learning experience.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Bodged bass and busted bellows
« Reply #3 on: April 16, 2013, 02:42:17 PM »

I could understand it as perhaps an old field repair that worked OK and so was never looked at again.  My own camping coffee pot's lid is held on with a paper clip -  and actually I quite like the memories of St Chartier 1993  that come with that.

More to topic: Theo might have noticed (but is far too polite to comment!) that several reed plates in my Lilly had once been 'soldered' back in with a hot tent peg! Little Fred(3) was on my shoulders at Beverley and gave its strap (left shoulder) a good toddler's kick.  Big whoops (onto paving slab) wrt its reeds. I have to add .. much tribute to the solidity of construction of the frame in those little Castagnaris!  :|glug
Logged
  _       _    _      _ 

Wulfrun

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: Bodged bass and busted bellows
« Reply #4 on: April 29, 2013, 09:47:54 PM »

Finally had chance to have a look at the box

Before investing time and money give all the woodwork a thorough examination looking for damage from damp, either rot, or more likely glued joints that have failed.  Also examine the bellows and work out where the air is leaking from, and if it looks repairable.  You need a sound wooden case, and bellows if the project is to be worthwhile. 

Woodwork: water stains inside the treble end (including where the felt has transferred colour onto one of the reedblocks. Nothing appears to be warped though. Couple of failed joints internally but they don't seem to have moved - can these be fixed with PVA wood glue?

Case: sound, trim on the edges needs replacing, as do all the leather straps & fittings which have perished. Bellows frame fits well and doesn't appear to be leaking air, though I will be replacing the gaskets as a matter of course (based on the assumption that they're as filthy as the rest of the box was.

Bellows: picture attached (though those of nervous disposition may wish to look away!). these were more or less airtight before I removed the manky electrical tape and parcel tape that was holding them together to reveal 6 or seven splits on the lower edge of the back long side, the largest is about 3", they go all the way through the card and almost seem to be 'carved' into the boards.  :( I'm not sure if its going to be worth trying to save them but will be giving the 'cereal box trick' a go as soon as we have an empty one.

There aren't that many old Hohners that are truly beyond redemption but whether or not you think it'll be worthwhile depends on how much money and work you're willing to put in and if you want to save/make money or if you're doing it for fun or as a learning experience.

The main reasons for taking on this box are the fact that I could do with a 2.5 row (...not MAD...yet...honest...), mostly for the challenge and to keep me out of mischief! The hope is to get a playable instrument for a lot less than the £400+ that seems to be the going rate for similar beasties that I've seen lurking in music shops. I'm not intending to make money out of it - unless its from the neighbours paying me to stop playing when its finished!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal