Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner pallet facing upgrade. Dealing with air leaks.  (Read 5915 times)

0 Members and 1 Guest are viewing this topic.

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Hohner pallet facing upgrade. Dealing with air leaks.
« on: May 15, 2013, 08:45:22 AM »

I've just finished de-percussionifying an Erica's treble pallets with felt-cushioned leather, but the pallets no longer sit flat on the inside row and there is now a gap at the end of each pallet. This is where I could do with advice before ruining (yes I know, I've already done that by taming the clack...) it.

Do I individually bend each arm so the pallets sit flat again, or is there a better solution? Will they simply settle and bed in after a day or two?
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #1 on: May 15, 2013, 08:54:46 AM »

I've just finished de-percussionifying an Erica's treble pallets with felt-cushioned leather, but the pallets no longer sit flat on the inside row and there is now a gap at the end of each pallet. This is where I could do with advice before ruining (yes I know, I've already done that by taming the clack...) it.

Do I individually bend each arm so the pallets sit flat again, or is there a better solution? Will they simply settle and bed in after a day or two?

Did you remove the pallets to reface them? If not the pallets will not sit at the right angle due to the increased thickness of the material. If you did remove them you should then have replaced them under the spring tension and then applied your adhesive of choice (I use hot glue) and they should be sat down properly. You should not need to bend the arms.

ps Like de-percussionifying

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #2 on: May 15, 2013, 09:28:06 AM »

Wot Lester said...

Your course of action now is to remove all the pallets from the levers and clean off all the old glue, then re-glue the pallets back in position. It's easier to do this if you remove the entire treble end mechanism first:

1. Remove the keyboard by unscrewing the long screws at each end. You will need to remove the bellows pins to gain access to the screw heads inside the RH end. Also remove the grille.

2. Release all the lever arm springs first of all - a hook-type of tool like a crochet hook or bent paper clip is useful here - then remove the mechanism by unscrewing the 3 or 4 small screws which secure the mechanism to the wooden casework.

3. Carefully applied brute force/twisting/glue removal should allow you to remove the pallets from the lever arms. Clean off old glue from pallet slots and lever arm ends.

4. Re-assemble mechanism and re-attach springs and keyboard, but leave pallets off for the moment.

5. Re-insert pallets back in their place; the spring tension should hold them in position. Check to see they are all nicely lined up and the felt is sitting nicely flush on the pallet board and cover all the sound holes.

6. Re-glue the pallets on to the lever arms using hot melt glue, or if you are a purist, linen disks and animal/hide glue.

7. You will probably find that the buttons are now too low in the keyboard, due to the extra thickness of the new pallet facing. You can adjust this by very gently and carefully bending the lever arms outwards from the pallet board using pliers or a hook-type tool. Check with a straight edge on the button tops to see that the button heights are the same all along the keyboard.

8. You may also find the buttons are no longer central in the keyboard holes and scrape against the sides of the holes. The remedy is to insert thin round-nosed pliers down the hole next to the side of the button. Grip the lever arm and just gently ease the arm one way or t'other until the button is central again.

9. Refix the grille and you're done!

Overall, this is not a difficult job, but it does need some time, patience and a reasonable degree of care in handling the components.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #3 on: May 15, 2013, 09:30:27 AM »

Couple of things from Steve's comprehensive instructions.

You can remove the pallets without removing the mech from the soundboard, saves time if nothing else. But more importantly I would recommend realigning the button heights prior to gluing the pallets in place as the adjustment can (and from bitter experience does) cause pallets to become misaligned..

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #4 on: May 15, 2013, 09:31:46 AM »

Thank you for the helpful replies.

I didn't prize the pallets off, mainly because I don't have a hot glue gun. Would reed wax or PVA be sturdy enough to use instead?
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #5 on: May 15, 2013, 09:36:46 AM »

Thank you for the helpful replies.

I didn't prize the pallets off, mainly because I don't have a hot glue gun. Would reed wax or PVA be sturdy enough to use instead?

Wax is used by a number of people with success I believe.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #6 on: May 15, 2013, 09:41:39 AM »

Thank you for the helpful replies.

I didn't prize the pallets off, mainly because I don't have a hot glue gun. Would reed wax or PVA be sturdy enough to use instead?
Hot glue guns are not expensive. I think mine cost about £15 from B&Q or Homebase. Very useful piece of kit for all sorts of jobs, so a worthwhile investment.

I believe pallets are sometimes fixed using wax, but I've no experience of this. Intuitively, it seems not quite strong enough and prone to softening in hot weather, but I may be wrong.

You could use PVA, but it sets very strongly and is difficult to remove/adjust in the future without damaging the wooden pallets. It is also very rigid once dry. Personally I would recommend hot melt glue. It retains a degree of flexibility in the joint so helps the pallet bed down properly.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #7 on: May 15, 2013, 09:48:40 AM »

Wax is not strong enough for Hohner pallets which haze a fairly small contact area. If you use pva then you would also need to apply a small cloth or leather patch as originally fitted. Don't even think about using the original ones. Circles can be pinched out of any flat textile, or strong paper.  Shape is not important, if you have no punch then cut squares with scissors.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #8 on: May 15, 2013, 11:46:59 AM »

Ok, thank you for the advice and guidance.I shall hold fire until I can obtain a glue gun and some glue!
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #9 on: May 24, 2013, 01:40:31 AM »

Success!
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #11 on: July 25, 2013, 01:12:40 PM »

Wax is not strong enough for Hohner pallets which haze a fairly small contact area. If you use pva then you would also need to apply a small cloth or leather patch as originally fitted. Don't even think about using the original ones. Circles can be pinched out of any flat textile, or strong paper.  Shape is not important, if you have no punch then cut squares with scissors.

Rather than dispensing dodgy advice  :-[ I have a couple of questions.

1) On my HA114, on the treble pallets, there is a little disk of cloth glued on top of where the metal arm slots into the back of the pallet (as described above). What are the disks for?
2) I think I understand the advice about using hot glue. If at a later stage the pallets need re-felting again is the hot glue removed by heating?

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #12 on: July 25, 2013, 03:01:19 PM »

Wax is not strong enough for Hohner pallets which haze a fairly small contact area. If you use pva then you would also need to apply a small cloth or leather patch as originally fitted. Don't even think about using the original ones. Circles can be pinched out of any flat textile, or strong paper.  Shape is not important, if you have no punch then cut squares with scissors.

Rather than dispensing dodgy advice  :-[ I have a couple of questions.

1) On my HA114, on the treble pallets, there is a little disk of cloth glued on top of where the metal arm slots into the back of the pallet (as described above). What are the disks for?
2) I think I understand the advice about using hot glue. If at a later stage the pallets need re-felting again is the hot glue removed by heating?
The linen disks are there to provide some extra gluing area, helping to secure the pallet on to the pallet arm. Originally animal/hide glue was used for this, and I still think this is a good approach, as it enables easy removal at some (hopefully distant) point in the future when the refacing job needs to be redone. You could use PVA too - although my instinct would be to dilute it with water somewhat. But future removal is likely to be harder with PVA.

For my re-facing jobs, I use hot melt glue for refixing the pallets on the pallet arms. In this case you don't need to use the fabric disks - just put a blob of hot melt glue over the pallet arm where it sits in the pallet slot.

I've successfully removed old hot melt glue by using a soldering iron at low temperature to soften the glue and scraping it off with a blunt blade. If you get the old glue too hot it starts to burn and darken, and the fumes are very unpleasant, so make sure you are in a well-ventilated environment, preferably with some sort of fan blowing the fumes away from your face. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #13 on: July 25, 2013, 03:25:03 PM »

I've only just come across this thread. The horrible smell is cooking hoof and horn/ pearl glue.
I'm a great believer in belt and braces, eg the little dots of material , adds extra strength as has been said.
The Chanson uses duct tape, it works but only just. PVA is a swine to remove but you can buy " reversible" PVA.
The method of of removing both, reversible PVA and Pearl is to damp it slightly then go on your holidays when you come back the glue will have softened ( I mean an hour or so of course)
And will be easy to remove.  You mustn't over wet it or the pallet will warp, a good idea is to take a wad of blotting paper damp it and place over the pallet. I'm still not convinced about reversible PVA.
but I am an old git and hopefully not averse to new technology so hot glue I think is the way to go.
Hot glue pots are expensive, in anyone wants to know how to make one for nothing you can always PM me.  ::)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #14 on: July 25, 2013, 03:35:22 PM »

I've only just come across this thread. The horrible smell is cooking hoof and horn/ pearl glue.
.....
Nick - are you confusing the smell of hot animal glue (which I agree can be strong and somewhat unpleasant) with what I was describing: the smell of over-heated hot melt glue which, as far as I am aware, is a synthetic thermoplastic material, which releases absolutely diabolical fumes when scorched. The fumes give me a nauseous headache as quick as anything.  :(
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #15 on: July 25, 2013, 03:46:07 PM »

Thanks Steve and Nick. I'll let you know how I get on.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #16 on: July 25, 2013, 05:46:41 PM »

It is not necessary to re heat the glue from a hot melt gun. It will usually peel off fairly easily.

Whatever sticky stuff you use don't be tempted to put it in the pallet groove and then press in the lever.  That way it's almost impossible to remove the pallets without damage.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #17 on: July 26, 2013, 12:08:49 AM »

It is not necessary to re heat the glue from a hot melt gun. It will usually peel off fairly easily.
Usually I would agree, but the experience I was describing involved really old hot melt glue which had set/aged rather hard and wouldn't peel off cleanly.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #18 on: July 26, 2013, 03:03:02 AM »

I only use wax to secure pallets, (plus small squares of the blue paper kitchen wipes material), and temperatures here get to 40+ in summer. I have had no problems with pallets coming adrift. Old wax is much easier to remove than PVA or hotmelt glue.
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner pallet facing upgrade. Dealing with air leaks.
« Reply #19 on: July 26, 2013, 07:58:33 AM »

I've only just come across this thread. The horrible smell is cooking hoof and horn/ pearl glue.
.....
Nick - are you confusing the smell of hot animal glue (which I agree can be strong and somewhat unpleasant) with what I was describing: the smell of over-heated hot melt glue which, as far as I am aware, is a synthetic thermoplastic material, which releases absolutely diabolical fumes when scorched. The fumes give me a nauseous headache as quick as anything.  :(

Yes I did confuse it  :|bl
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal