Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Size matters?  (Read 5694 times)

0 Members and 1 Guest are viewing this topic.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Size matters?
« on: July 22, 2013, 11:09:20 AM »

Hi All,
Got a thought going round and round....... and thinking out loud here.....
My first box is a Tommy, bought simply because it was compact and felt good. Size is 24cm x 15cm.
A common complaint with the Tommy is that it is a compromise - great box but to get everything into it, the basses are a touch weak. Mine is a second generation one with 3 notes in the chords as earlier ones used the bass as well to make the third note of the chord (? some thing like that! ) great sound but not the best basses.
On my learning curve I bumped into a Melnetter who played her Dony at me, a full sized box, and then played my Tommy at me. I then realised what was commonly referred to as 'a full sound from a full sized box'.
I've now happened on a Hascy which is larger, 28cm x 17cm and gives that rich full sound, basses to die for too!
Side by side, the Tommy and Hascy are not that much different in size, but the sound is utterly different.

I've been following the Vander Aa thread and suddenly realised his 'Compact' model is 28cm x 16, which is just over the sized of my Hascy and not what I'd call 'compact'.
If, as said here, this V-D-A was the idea that drove Oakwood to make their fabled boxes, how large was a standard 2 row Oakwood?

I've seen comments that some Oakwoods were less good on the bass side and that some were mm's larger and had great basses. The implication being that it's mm differences that can count to make or break a sound.

My question is:-
Is there a size point where the bass sound drops off to accommodate the smaller size of a compact box?
....or is it combinations of not just size, but reeds, chamber design etc that contribute to the bass sound?

Just one of those things pinging round my poor heat adled brain!
cheers
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Size matters?
« Reply #1 on: July 22, 2013, 11:49:20 AM »

My question is:-
Is there a size point where the bass sound drops off to accommodate the smaller size of a compact box?
....or is it combinations of not just size, but reeds, chamber design etc that contribute to the bass sound?

A bit of both. A smaller box size certainly will limit the level of fundamental from the lowest bass reeds, but anyway the box designer has to decide on some kind of compromise in the reeds and blocks because they make a lot of difference.

One choice is where the break comes - if you arrange the bass notes in ascending scale order, there is a point at which the pitch jumps down 6 notes instead of up one. That point is not the same on every box, and defines the lowest reed note.

Another choice is whether to have two or three reeds per bass note. Three gives you very loud and fast basses (it does on my DB super prototype, anyway) but the loudness isn't actually at the low frequencies. Two reeds per note may enable you to have bigger and lower pitched reeds, with more real bass but perceived as quieter.

It's further complicated by the fact that the basses sound different at a distance, where the higher octave reeds carry better than the lower reeds.

On top of that there is the need to get a sensible tonal balance between RH and LH...
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Size matters?
« Reply #2 on: July 22, 2013, 12:35:10 PM »

Fair enough. It is "compact" wrt his standard size .. which is more or less "standard". I'm sure more metal could be ground off the reed plates, but smaller chambers then change tone, especially for those low notes as Anahata points out

Not sure what compromises Castagnari made with their Tommy - it is a wonderful piece of kit - but more so the more you play it push-pull. I'm more of a pull sort of chap and value vdAa/Oakwood's larger bellows  :||:

So compromises all round, as ever with melodeonics.  As luck has it I made a pic of my boxes - attached after a bit of file size reduction. The Gaillard is standard size for 3 voices and the vdAa certainly feels smaller. The *Oakwood "compact" is smaller again (mainly in depth) and is lighter again, but has only two M+M voices. You takes yer choice.
*For sale to a Good Home once I get back from France

« Last Edit: July 22, 2013, 12:40:32 PM by Chris Ryall »
Logged
  _       _    _      _ 

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #3 on: July 22, 2013, 01:10:36 PM »

Thanks guys.....
I had a horrible feeling it wouldn't be straightforward! Lots of things for me to think about.
It was never going to be simple was it  ;D

Nice photo Chris. It does make the point that in 3 row breeds, v-d-a and Oakwood *are* compact compared to a traditional maker like Gaillardia.
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Size matters?
« Reply #4 on: July 22, 2013, 02:11:04 PM »

Thanks guys.....
I had a horrible feeling it wouldn't be straightforward! Lots of things for me to think about.
It was never going to be simple was it  ;D

Nice photo Chris. It does make the point that in 3 row breeds, v-d-a and Oakwood *are* compact compared to a traditional maker like Gaillardia.
Q
The small Oakwoods that Martyn started off making did have somehwat weak basses, which were also prone to choking and pulling off pitch when played hard. I asked him to make me a box with better basses -- the first Model 4 -- and this meant increasing the size of the reeds and reed blocks (the original ones were rather small), in fact the measurements were taken off my Dony which has an excellent bass end sound. The difference this made was very obvious...

Another reason that large boxes often sound "bassier" (even with the same size reeds and blocks) is that the air enclosed inside the bass end forms a peaky lowpass (treble) filter together with the sound holes in the end cover plate. With smaller boxes the cutoff frequency is higher so more high frequencies escape -- which makes the basses sound more bassy -- and the peak moves up in frequency to give a more "honky" sound.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Size matters?
« Reply #5 on: July 22, 2013, 02:24:15 PM »

Thanks guys.....
I had a horrible feeling it wouldn't be straightforward! Lots of things for me to think about.
It was never going to be simple was it  ;D

Nice photo Chris. It does make the point that in 3 row breeds, v-d-a and Oakwood *are* compact compared to a traditional maker like Gaillardia.
Q
The small Oakwoods that Martyn started off making did have somehwat weak basses, which were also prone to choking and pulling off pitch when played hard. I asked him to make me a box with better basses -- the first Model 4 -- and this meant increasing the size of the reeds and reed blocks (the original ones were rather small), in fact the measurements were taken off my Dony which has an excellent bass end sound. The difference this made was very obvious...

Another reason that large boxes often sound "bassier" (even with the same size reeds and blocks) is that the air enclosed inside the bass end forms a peaky lowpass (treble) filter together with the sound holes in the end cover plate. With smaller boxes the cutoff frequency is higher so more high frequencies escape -- which makes the basses sound more bassy -- and the peak moves up in frequency to give a more "honky" sound.

So all you'd need to do to get a better bass end would be to enlarge the holes in the bass plate?

(assuming that there is adequate chamber volume for the bass reeds, which I fancy is not a sensible assumption for a small box).
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #6 on: July 22, 2013, 02:45:02 PM »

IanD: Thanks, that does make sense.
so was the model 4 Oakwood a 2 row? and if so, got a tape measure handy? !!
( re-reading before posting..... so do I assume that Martyn made the original Mk4 the same size as a Dony? )

Funny you mention 'honky' - that's how I feel about the Tommy.
Almost drifting my own thread here, but I've favoured the full sized Hascy ever since getting it. Recently, with a festival imminent and flight involved, I'd stated to play the Tommy a bit to get used to the smaller buttons and spacing, and it would fit into ( was! ) the handluggage.
I've become aware of the honky sound and it's immediate response ( not that the Hascy's slow ). I keep thinking of Anahata's punchy style when I first saw him on Youtube on his Oakwood. The Tommy too lends itself to being played in a punchy style, great for the majority of my playing which is English dance ( session ) tunes. It also means trying to be punchy, I don't tend to lean on the basses quite so much therefore they're less important....

and no Owen, I'm not taking a brace and bit to the Tommy's bass end   :P
 ;) Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Size matters?
« Reply #7 on: July 22, 2013, 04:21:52 PM »

Is some of the sound quality down to the hardness of the metal used in the reeds? I've heard thats certainly true for concertinas.

I've also noticed that the bass reeds in my Hohner Lilliput sound much bassier than the ones in the largr pokerwork. Maybe becuae they are the older pattern H reeds?
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Size matters?
« Reply #8 on: July 22, 2013, 04:26:40 PM »

Is some of the sound quality down to the hardness of the metal used in the reeds? I've heard thats certainly true for concertinas.

I've also noticed that the bass reeds in my Hohner Lilliput sound much bassier than the ones in the largr pokerwork. Maybe becuae they are the older pattern H reeds?

I would say stiffness has an impact, rather than hardness (the two concepts are distinct). So does the density. This is very noticeable when comparing bass reeds to steel reeds, whether different types of steel give significantly different sounds I do not know.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Size matters?
« Reply #9 on: July 22, 2013, 06:27:11 PM »

Thanks guys.....
I had a horrible feeling it wouldn't be straightforward! Lots of things for me to think about.
It was never going to be simple was it  ;D

Nice photo Chris. It does make the point that in 3 row breeds, v-d-a and Oakwood *are* compact compared to a traditional maker like Gaillardia.
Q
The small Oakwoods that Martyn started off making did have somehwat weak basses, which were also prone to choking and pulling off pitch when played hard. I asked him to make me a box with better basses -- the first Model 4 -- and this meant increasing the size of the reeds and reed blocks (the original ones were rather small), in fact the measurements were taken off my Dony which has an excellent bass end sound. The difference this made was very obvious...

Another reason that large boxes often sound "bassier" (even with the same size reeds and blocks) is that the air enclosed inside the bass end forms a peaky lowpass (treble) filter together with the sound holes in the end cover plate. With smaller boxes the cutoff frequency is higher so more high frequencies escape -- which makes the basses sound more bassy -- and the peak moves up in frequency to give a more "honky" sound.

So all you'd need to do to get a better bass end would be to enlarge the holes in the bass plate?

(assuming that there is adequate chamber volume for the bass reeds, which I fancy is not a sensible assumption for a small box).

Wrong way round -- smaller holes mean a more bassy (or to be more exact, less trebley) sound. But too small means not enough free area for the sound (and air) to get out. And the reeds (and reed chambers) are probably too small anyway...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Size matters?
« Reply #10 on: July 22, 2013, 06:31:12 PM »

IanD: Thanks, that does make sense.
so was the model 4 Oakwood a 2 row? and if so, got a tape measure handy? !!
( re-reading before posting..... so do I assume that Martyn made the original Mk4 the same size as a Dony? )

Funny you mention 'honky' - that's how I feel about the Tommy.
Almost drifting my own thread here, but I've favoured the full sized Hascy ever since getting it. Recently, with a festival imminent and flight involved, I'd stated to play the Tommy a bit to get used to the smaller buttons and spacing, and it would fit into ( was! ) the handluggage.
I've become aware of the honky sound and it's immediate response ( not that the Hascy's slow ). I keep thinking of Anahata's punchy style when I first saw him on Youtube on his Oakwood. The Tommy too lends itself to being played in a punchy style, great for the majority of my playing which is English dance ( session ) tunes. It also means trying to be punchy, I don't tend to lean on the basses quite so much therefore they're less important....

and no Owen, I'm not taking a brace and bit to the Tommy's bass end   :P
 ;) Q
Oakwood Model 4 is about 28cm x 15cm, I think the Dony is a little bit over 28cm x 17cm (and 12 basses, and heavier). The Dony bass sound is still a bit better than the Model 4, but the Model 4 is far better than the smaller Oakwoods.

Tommys seem quite variable, especially over the years -- my old G/C one sounds fabulous (but couldn't punch it's way out of a wet paper bag), but I've never really heard a D/G one I liked.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #11 on: July 22, 2013, 06:52:27 PM »

thanks Ian. Interesting dimentsions.
Off to  :M with 'you know who'!!
Will probably catch up at the weekend, and I might well have my Tommy along for your perusal.....
........if I can carry that *plus* the stick bag  :(
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Size matters?
« Reply #12 on: July 23, 2013, 04:40:24 PM »

thanks Ian. Interesting dimentsions.
Off to  :M with 'you know who'!!
Will probably catch up at the weekend, and I might well have my Tommy along for your perusal.....
........if I can carry that *plus* the stick bag  :(
Q
And it's promising rain/thunderstorms for Sunday in Warwick -- another dance-off in the Zetland, perhaps?  >:E
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Size matters?
« Reply #13 on: July 23, 2013, 05:09:10 PM »

When I first tried a DG Tommy, I was struck by how weak the basses sounded. I was quite surprised & disappointed. Then, as I played it more, I came to appreciate the punchy, sweet quality of the sound, which seemed very well-suited to some kinds of tune. However, switching back to my DG Le Bouebe, I immediately appreciated the much stronger, more resonant sound of the basses.

For me, the big question mark about the Tommy, is whether the 3rd voice, which adds a deeper tone to the sound, is a good trade off for the much lighter sound of the basses? The other thing I'm curious about, is how the sound of the basses on the Tommy compare with the Lilly - another very small box, but one that doesn't cram in 3 voices in the treble?
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #14 on: July 23, 2013, 06:29:28 PM »

IanD: hmmmmm that sounds like a road to destruction  ;D
Shame I'll be driving back and laying off the laughing liquid  :|glug

Airtime: there are different vintages of Tommy. The originals had thin basses, second. Generation improved ones. I swear the new ones I saw at festivals last year had changed and improved again but have no proof.
I'm starting to wonder if other things more than make up for the less punchy basses
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Size matters?
« Reply #15 on: July 24, 2013, 11:24:15 AM »

Quote
Airtime: there are different vintages of Tommy. The originals had thin basses, second. Generation improved ones. I swear the new ones I saw at festivals last year had changed and improved again but have no proof.
I'm starting to wonder if other things more than make up for the less punchy basses

I'm guessing that the Tommy I played was about 10 - 12 years old. This is a little clip I recorded of it:

http://www.youtube.com/watch?v=Y6UVkarej4A

I shouldn't really comment because I haven't tried a lot of DG boxes. Mostly, I've been playing Hohners & particularly my vintage BbEb, which has the deepest basses of any box I've tried - deeper than a GC's. I'm starting to think that my Saltarelle Le Bouebe has particularly deep basses for a DG. I've just taken possession of a Beltuna Alex, & while the basses are fuller than the Tommy's they don't have the depth of the Le Bouebe.
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #16 on: July 24, 2013, 01:01:57 PM »

Airtime: nice clip!
I thought that Tommy sounded quite nice. I would guess at the same era as mine, with the somewhat square logo, mine's got '2004' written in pencil inside the grill so fairly spot on for age.

You've made a very interesting point, inadvertantly bringing it right back to my original thoughts.
The Tommy is 24cm x 15cm, and a quick google gives the le Boube at 26cm x 15cm.
At Chippenham I saw a Castagnari Laura on Rees's stall, which is 26cm x 16.5cm and had a quick go. It was really lovely! Much more like the rich basses of the Hascy as opposed to the thinner Tommy. It was only a quick go but very enjoyable. I'm intent on another go at Sidmouth!
In fact, the Laura was part of the thoughts pinging round in my head leading to this post. The jump in size is only 2 cm larger from the Tommy but the sound markedly different. You have had a similar experience with the sound from only a slightly larger le Boube.

I wonder if the increased ( size ) volume of the box when approaching 26cm ( i.e. 2 cm longer and another 1-1.5cm wider ) means the sound is no longer compromised?
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Size matters?
« Reply #17 on: July 24, 2013, 01:32:29 PM »

Airtime: nice clip!
I thought that Tommy sounded quite nice. I would guess at the same era as mine, with the somewhat square logo, mine's got '2004' written in pencil inside the grill so fairly spot on for age.

You've made a very interesting point, inadvertantly bringing it right back to my original thoughts.
The Tommy is 24cm x 15cm, and a quick google gives the le Boube at 26cm x 15cm.
At Chippenham I saw a Castagnari Laura on Rees's stall, which is 26cm x 16.5cm and had a quick go. It was really lovely! Much more like the rich basses of the Hascy as opposed to the thinner Tommy. It was only a quick go but very enjoyable. I'm intent on another go at Sidmouth!
In fact, the Laura was part of the thoughts pinging round in my head leading to this post. The jump in size is only 2 cm larger from the Tommy but the sound markedly different. You have had a similar experience with the sound from only a slightly larger le Boube.

I wonder if the increased ( size ) volume of the box when approaching 26cm ( i.e. 2 cm longer and another 1-1.5cm wider ) means the sound is no longer compromised?
Q
I'd hazard a guess that the small increase in external size is not so crucial (but see below), maybe the increase in reed block and/or reed size is more important? (the Tommy reed blocks and reeds are smaller than normal to fit in the small space available).

Also it's the internal volume of the bass end that affects the resonant frequency not just the height and width, and I know the Tommy has an unusually shallow bass end -- I assume the Laura bass end is considerably deeper? The Laura internal area is only about 20% bigger but the increase in depth is probably more than that...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Size matters?
« Reply #18 on: July 24, 2013, 02:32:03 PM »

IanD: It was the internal volume I was thinking of, being proportional the the external size, but as you quite rightly point out, depth is the third significant factor!
Overall volume has to be the significant factor.
Have no knowledge of the reed/reed block sizes, but yes that too must have some effect as Anahata pointed out earlier in the thread. Makes sense!
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Size matters?
« Reply #19 on: July 24, 2013, 09:33:01 PM »

frans van der Aa asserts that block size, amd wood, and size of slot chsnge tone, and he also crosslinks the blocks with a kinked wire, that will change the impedance of any coupling when several reeds are in play (mainly wrt phase IMO). Gaillard's kit vibrates in your hands on lower notes ( i suspect Strad violins are the same). acoustic coupling ramifying as far as the fingerboard must have tone effects?

It's very complicated.

[corrected for iTypos and wrt clarity]
« Last Edit: July 25, 2013, 04:39:02 AM by Chris Ryall »
Logged
  _       _    _      _ 
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal