Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner 1140C slow reeds  (Read 7625 times)

0 Members and 1 Guest are viewing this topic.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Hohner 1140C slow reeds
« Reply #20 on: December 24, 2013, 12:19:59 PM »

Glued-in blocks (especially in combination with 1st class reeds and large rectangular openings) yield a lot of extra punch! Admittedly, raising the pitch of pull reeds can become a bit awkward in those cases where the reeds are placed flat on the face board. Otherwise, no problem at all. But of course, you must know how to lift the inside reeds (even the smallest) without damaging them or altering that vital gap between the tip of the reed and the frame. Waxing is absolutely no problem if one is familiar with the methods used in most factories and doesn't depend on a soldering iron.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner 1140C slow reeds
« Reply #21 on: December 24, 2013, 12:33:17 PM »

Glued-in blocks (especially in combination with 1st class reeds and large rectangular openings) yield a lot of extra punch! Admittedly, raising the pitch of pull reeds can become a bit awkward in those cases where the reeds are placed flat on the face board. Otherwise, no problem at all. But of course, you must know how to lift the inside reeds (even the smallest) without damaging them or altering that vital gap between the tip of the reed and the frame. Waxing is absolutely no problem if one is familiar with the methods used in most factories and doesn't depend on a soldering iron.
How would you go about lifting the very small highest pitch reeds in this instance?
I normally use the Italian hook method to raise the inside reeds, but not for the smallest ones. For these, I use a very thin brass reed lifter pushed through the reed block vent - I don't try to 'ping' the reed tongue up with the reed lifter as I think that would damage the very thin tip and/or alter the reed tip gap. But I don't think my method would work in the case of glued-in reed blocks.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Hohner 1140C slow reeds
« Reply #22 on: December 24, 2013, 01:03:46 PM »

For those hard to raise reeds, I remove the reed plate, tune, and reinstall. Takes a bit longer but doesn't make me near as nervous.  Actually really doesn't take long to remove and reinstall once you get the hang of it.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Hohner 1140C slow reeds
« Reply #23 on: December 24, 2013, 01:07:03 PM »

I prefer calling the Italian tool "key" (based on how it is used) and the german counterpart ( Rausheber) "hook". Personally, I use the Ialian key for the lowest reeds, in all other cases the "rausheber" (in different sizes) all the way up to the smallest reeds on any M row in any key (at least if they are standard Hohner or Italian quality). The latter method is also much faster, because one doesn't  have to change tool for lack of a third hand. In the rare case of encountering ottavini reeds (the very smallest, usually mounted on thin brass frames) that have to be raised, I prefer removing them from their wax bed, as suggested by Bryan.
« Last Edit: December 24, 2013, 01:09:19 PM by diatonix »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner 1140C slow reeds
« Reply #24 on: December 24, 2013, 03:09:33 PM »

Thanks both Diatonix and Bryan!
I can see that removing the reed plate from the block/bed is the safest way to go for the very smallest reeds. In that case I guess you would have to tune the reed tongue by offset difference; i.e. if the reed is 5 cents sharp in-situ in the instrument, you would flatten it by 5 cents on the tuning table/rig, regardless of what the actual target value of the reed might be.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Hohner 1140C slow reeds
« Reply #25 on: December 24, 2013, 03:16:37 PM »

I tune it using it's proper place in the reed block. I sound it in place, remove it and file a little, put back in place and sound again.  Sounds tedious, and it is, but not as bad as it seems.  If it is very far off, I flip it over and tune like as a push reed, then check in it's proper position for fine tuning, which is often not needed.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner 1140C slow reeds
« Reply #26 on: December 24, 2013, 04:30:12 PM »

I tune it using it's proper place in the reed block. I sound it in place, remove it and file a little, put back in place and sound again.  Sounds tedious, and it is, but not as bad as it seems.  If it is very far off, I flip it over and tune like as a push reed, then check in it's proper position for fine tuning, which is often not needed.

That's exactly what I do for small reeds, I find it far to easy to damage them doing it any other way.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner 1140C slow reeds
« Reply #27 on: December 24, 2013, 04:30:51 PM »

I tune it using it's proper place in the reed block. I sound it in place, remove it and file a little, put back in place and sound again.  Sounds tedious, and it is, but not as bad as it seems.  If it is very far off, I flip it over and tune like as a push reed, then check in it's proper position for fine tuning, which is often not needed.

This is what I do, Steve. It gives the best results.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner 1140C slow reeds
« Reply #28 on: December 24, 2013, 04:44:29 PM »

That's what I do if the pitch is flat, but if it is sharp I find it's usually possible to scratch it in situ.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner 1140C slow reeds
« Reply #29 on: December 24, 2013, 04:48:29 PM »

That's what I do if the pitch is flat, but if it is sharp I find it's usually possible to scratch it in situ.

Me too.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner 1140C slow reeds
« Reply #30 on: December 24, 2013, 05:20:25 PM »

That's what I do if the pitch is flat, but if it is sharp I find it's usually possible to scratch it in situ.

Me too.
Certainly.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner 1140C slow reeds
« Reply #31 on: December 24, 2013, 05:34:50 PM »

Thanks everyone for the excellent advice as usual!  (:)
Happy Christmas!  :|glug
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Hohner 1140C slow reeds
« Reply #32 on: December 24, 2013, 08:33:18 PM »

Thanks everyone for the excellent advice as usual!  (:)
Happy Christmas!  :|glug

isn't it great when members of the master fettler's guild ''gatling gun'' it out like that!   ;D 
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner 1140C slow reeds
« Reply #33 on: December 25, 2013, 01:29:02 AM »

Thanks everyone for the excellent advice as usual!  (:)
Happy Christmas!  :|glug

isn't it great when members of the master fettler's guild ''gatling gun'' it out like that!   ;D

It's what we do. Merry Christmas melnetters one and all.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner 1140C slow reeds
« Reply #34 on: December 25, 2013, 06:31:24 PM »

I prefer calling the Italian tool "key" (based on how it is used) and the german counterpart ( Rausheber) "hook". Personally, I use the Ialian key for the lowest reeds, in all other cases the "rausheber" (in different sizes) all the way up to the smallest reeds on any M row in any key (at least if they are standard Hohner or Italian quality). The latter method is also much faster, because one doesn't  have to change tool for lack of a third hand. In the rare case of encountering ottavini reeds (the very smallest, usually mounted on thin brass frames) that have to be raised, I prefer removing them from their wax bed, as suggested by Bryan.

So..what's is an Italian key and what is the German hook?
And I'm still a bit baffled on how you rewax the reed plates in the confined space between the upright blocks on a Hohner 114 - assume you use a specially adapted waxing spoon?

And a happy Christmas to all you wonderful melnetters.
Roger

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Hohner 1140C slow reeds
« Reply #35 on: January 05, 2014, 03:14:16 AM »

@ Roger: There is now a short video on YouTube that shows  both tools and how they are used.
http://www.youtube.com/watch?v=rdap-lYsKbw
Logged

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Hohner 1140C slow reeds
« Reply #36 on: January 05, 2014, 03:30:46 AM »

@ Roger: There is now a short video on YouTube that shows  both tools and how they are used.
http://www.youtube.com/watch?v=rdap-lYsKbw

Wonderful video! Very very useful. (Now where is that "like" button?)  (:)

Stephen
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Hohner 1140C slow reeds
« Reply #37 on: January 05, 2014, 04:15:24 AM »

That is nice to hear. Thanks, Stephen!
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal