Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: humidity swells wood  (Read 2726 times)

0 Members and 1 Guest are viewing this topic.

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
humidity swells wood
« on: August 08, 2013, 12:38:28 PM »

Hello all,

I have a single-row, built in Louisiana (where you'd think they would allow for humidity affecting wood parts!), about 2 1/2 years old.  Besides the other issues I've had to pay to have repaired now there is a problem with the wood treble levers swelling and rubbing in the slots on the keyboard. It appears the wood lever is rubbing both sides of the lever part that holds the treble button.  I hope this all makes sense.

I have considered pulling the axle on which all the levers/keys pivot.  Then I would be able to lightly sand all wood parts to allow for any future expansion. Any warnings about this procedure?  Advice on the best way to remove the axle?  Or, is there a wood-to-wood lubricant which will help alleviate the problem?

Thanks for any help.

Ken
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: humidity swells wood
« Reply #1 on: August 08, 2013, 01:06:07 PM »

I have considered pulling the axle on which all the levers/keys pivot.  Then I would be able to lightly sand all wood parts to allow for any future expansion. Any warnings about this procedure?  Advice on the best way to remove the axle?  Or, is there a wood-to-wood lubricant which will help alleviate the problem?
Very light sanding with fine (600 grit) paper may help, but be careful not to take too much off otherwise the levers will have too much clearance in the slot and could wobble/rattle. Burnishing by rubbing the sides of the levers on a smooth surface (glass sheet or similar) is also a good option.

If many of the levers are sticking, you would probably be best off removing them all in order to work on them. This will mean removing the axle. To remove the axle, be sure you have released all the springs first. In the Louisiana design of instruments, the springs are usually visible in the narrow slot at the rear edge of the keyboard. A hooked tool such as a crochet hook or even a bent paper clip can help with unhooking the helical springs. Be careful not to lose any in the process!

Once you have released all the springs you should be able to remove the axle, but you will probably need to remove the end pieces of the keyboard to get access to the ends of the axle. If there is a short length of the axle end protruding you may be able to grip it with pliers and begin to pull it out with a straight pull. Take care not to bend the axle rod. If there is no end protruding you will have to push the axle rod out from one end using a similar piece of wire as a punch/pusher tool until there is sufficient rod showing for you to grab hold of it with pliers.

If there are only one or two keys sticking, it may be possible to burnish the sides of the slots/key arms using a thin smooth steel shim or feeler gauge blade, in which case you don't need to go through the rigmarole of removing the springs and axle.

On no account attempt to lubricate the slot or the wood with any oil, grease or polish whatsoever. It will eventually end up making a sticky mess which will attract dust and make matters far worse. The only permissible lubricant is very fine dry graphite powder such as locksmiths use.

Good luck!

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: humidity swells wood
« Reply #2 on: August 08, 2013, 03:03:54 PM »

Ken, it may be the slot, but it is usually the axle that is sticking.  Removing the rocker enough to sand is tough, because you have to remove the button to take the rocker completely out.  Sometime you can tilt it up enough to sand it, and if it's the axle hole, you can definitely get to it.  If it's the axle hole, I use the next size numbered drill bit bigger than the axle, so if it's a 3/32" axle, use a #41 bit for the rocker hole, but don't do it with a power drill if tilting out of the slot.  If you want, give me a call, and I can walk you through your options.  If you do try to do it, I suggest pulling the springs off and laying them in order on a piece of masking tape placed on the table sticky side up, they usually need to go back on the same rocker, and dropping all ten on the ground is not fun (guess how I know).

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: humidity swells wood
« Reply #3 on: August 09, 2013, 09:17:09 AM »

...Removing the rocker enough to sand is tough, because you have to remove the button to take the rocker completely out...
I guess it depends on the actual method of construction used, but in my (admittedly limited) experience, there is a keyboard top cover plate which is held in place by screws and can easily be removed. This then allows access to the rocker arms without the need to remove any buttons. The attached photo shows the keyboard assembly of my own 'Stowmarket Golden Box' with the top cover plate removed. The springs have also been removed to allow the rocker arms to be tilted forward temporarily in order to fit a green felt buffer to limit the key travel.

One other point worth mentioning regarding lubrication: During the construction of this instrument (under the guidance of Emmanuel Pariselle on the 2008 EATMT melodeon making course) it was recommended to thoroughly wax the axle rod by rubbing with a wax candle prior to the progressive insertion of the axle rod. I think this is the only exception it is permissible to make to the 'no lubrication' rule mentioned previously.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: humidity swells wood
« Reply #4 on: August 09, 2013, 01:23:20 PM »

Update:  after reading the suggestions and talking with Bryan and having him guide me-step-by-step through the repair process I spent time last night attending to the box and Voila!  Problem solved!  I methodically disassembled the box, removed the axle cap, carefully removed the springs (I know I'll find the one that shot off somewhere into the basement...) and secured them to a piece of tape and numbered their positions for the re-assembly.  I carefully pulled the axle from the slot then was able to maneuver the rockers up and down enough to be able to have access to the pivot holes.  Most were fine.  The 5 and 6 holes needed to be opened just a little.  Then with my jewelry-making tools and files I carefully sanded both sides ot the rockers on all the keys.  Still, the #6 was sticking.  I then gently filed the interior slots and was happy to see that ll the rockers moved easily.

I wiped down the axle, applied a very light coating of Slideez to it and threaded it back through the pivot holes in the rockers.  I found that the builder had left his mistakes and first attempts as there were two rockers with double-drilled holes but once lined up there was no problem with re-assembly.

Re-attached the springs, put the box back together and entertained the crickets after midnight.  If anything, and I may be imagining this, but I think it plays better than before.  The box, not me.

So, after all this I have to say that, even though I have been annoyed by the construction quality of this accordion, I am thoroughly impressed by the amount of work that has to be done to construct one of these melodeons.  There are many steps in the process and elements in the design and it takes a careful and diligent and fastidious person to be able to perfect, or come close to perfecting, each part of the build.  My compliments to all who have taken up the challenge to build or even have attempted to build one of these beasts.  And, especially thanks to Bryan LaFleur for taking the time to help. If any of you don't know by now, he builds wonderful accordions.  I've had the chance to play only one but it was a joy.  Like butter...

ken
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: humidity swells wood
« Reply #5 on: August 09, 2013, 03:38:50 PM »

Well done Ken! Glad you have had a successful outcome. You'll be building your own next!  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: humidity swells wood
« Reply #6 on: August 09, 2013, 05:35:47 PM »

You'll be building your own next!  (:)

 ;)  Yep, heck, it's just a wooden box. he he

kenakordeon

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 264
Re: humidity swells wood
« Reply #7 on: August 09, 2013, 10:00:55 PM »

This then brings me to the subject of a building workshop.  I've read and heard good comments about the Emmanuel Pariselle workshops.  Anyone know of anything similar in the States or Canada?  (I think there was one in Canada a few years back but not sure.) Bryan, have you thought about the possibility?  Other folks who have attended the Pariselle  workshops can provide further information but it seems as if the time is spent measuring and cutting, and constructing and finishing the boxes with the reed blocks built with reeds installed and tuned, prior.  I would estimate that the cost of the instructor's time including materials might run to about $1200 - 1600 for a week?

Any thoughts?

Ken
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: humidity swells wood
« Reply #8 on: August 10, 2013, 12:43:01 AM »

Other folks who have attended the Pariselle  workshops can provide further information but it seems as if the time is spent measuring and cutting, and constructing and finishing the boxes with the reed blocks built with reeds installed and tuned, prior.  I would estimate that the cost of the instructor's time including materials might run to about $1200 - 1600 for a week?
On Emmanuel Pariselle's courses, some components are supplied ready-made: reeds, bellows, turned wood stops, decorative marquetry inlay strips, brass decorative corner pieces, bellows straps, rocker arms, pallets (without facing). Everything else you make from scratch.

EP brings selected timber and hardware/consumables such as screws, nails, leather, glue, varnish, etc. You have to cut the wood to size, sand and finish it, construct the casework, including mitred corners; more sanding. The reed blocks are made using jigs which EP brings along. The reeds are supplied roughly tuned, but further fine tuning is needed once they are installed in the finished instrument.

The 2008 course cost £1000 for a week's course, including all materials and tuition, but not accommodation/living expenses. I don't know what the current price is.

More information here.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: humidity swells wood
« Reply #9 on: August 10, 2013, 01:33:06 AM »

there is a keyboard top cover plate which is held in place by screws and can easily be removed.

I was referring to the Cajun style boxes, and in particular this accordion, which has a thin strip glued onto the keyboard to prevent the rockers from tipping up when removing the keyboard. But being glued in makes completely removing the rockers impossible without removing the buttons.  It looks good, but not very service friendly.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: humidity swells wood
« Reply #10 on: August 19, 2013, 09:28:52 PM »

In the US you can buy Teflon powder in a tube. I have used this on wood keyboards when rebuilding them. You basically rub some of the powder on the sides of the keys after you have cleaned and made any adjustments.
This can speed up the action a little and prevent wear, and it is basically colorless.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal