Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: How to remove the bellows...  (Read 3475 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
How to remove the bellows...
« on: August 22, 2013, 03:26:28 PM »

Attached is photo of terrible old box that I would like to take apart, but I don't see any bellows pins.
Would any kind person out there 'in the know' be prepared to share the secret of how to get the bellows off without wrecking the them?
Thanks in advance...  :|glug

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to remove the bellows...
« Reply #1 on: August 22, 2013, 03:37:56 PM »

At a guess there will be long screw top and bottom on the front face of both bass and treble ends. Undo then and Robert will be your father's brother.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to remove the bellows...
« Reply #2 on: August 24, 2013, 04:39:27 PM »

At a guess there will be long screw top and bottom on the front face of both bass and treble ends. Undo then and Robert will be your father's brother.

Thanks Lester..  exactly right.

Attached is a picture of its reed plates.
I can see how I can get at the upper reeds to tune them, but how does one tune the reeds on the other side of the plate? I assume this is done when the plate is taken off for rewaxing, or is there a technique to get at the reads from the top? I'm going to take the reed plates off anyway - so are they tuned when they are off the box? Or is this box such rubbish that there is no way to tune it?
I'd like to get this box into a marginally playable state, by taking it completely to bits etc. The bellows are in quite good nick, though I think I might have to make some new pallets.
The reeds look like brass to me and the valves are soft leather.
Thanks in advance etc.
Roger




an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: How to remove the bellows...
« Reply #3 on: August 24, 2013, 04:56:44 PM »

You are quite lucky really ;)
Those plates look to be pinned onto leather so you may not have to contend with waxing.
Brass reeds are so soft you will not even need a dremel -  abrasive paper will do.
All you have to fathom is a way of sounding them, possibly using the boxes own bellows - it is all searchable here as are methods to reach the suck side!
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to remove the bellows...
« Reply #4 on: August 24, 2013, 05:07:52 PM »

You are quite lucky really ;)
Those plates look to be pinned onto leather so you may not have to contend with waxing.
Brass reeds are so soft you will not even need a dremel -  abrasive paper will do.
All you have to fathom is a way of sounding them, possibly using the boxes own bellows - it is all searchable here as are methods to reach the suck side!
OK so the technique is to tune em through the slots from the exposed side..

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove the bellows...
« Reply #5 on: August 24, 2013, 05:10:47 PM »

Before even attempting to tune you will need to replace all the leather valves, the one you can see and the ones underneath.   The reed plates are usually easy to remove by turning the bent screws along one long edge to allow you to lift that side and withdraw it from the other side.  Just replacing the vales will make it play much better. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to remove the bellows...
« Reply #6 on: August 24, 2013, 10:58:59 PM »

Before even attempting to tune you will need to replace all the leather valves, the one you can see and the ones underneath.   The reed plates are usually easy to remove by turning the bent screws along one long edge to allow you to lift that side and withdraw it from the other side.  Just replacing the vales will make it play much better.
Thanks Theo, yes i will do that. What is the best way to tweak the tuning...if that is needed?
The other question is this: the palettes are sort of nailed/screwed on to the wire arms. This method of fixing is pretty crappy. I could cut a groove In the backs of these palettes and glue them on... As described in another thread, but maybe this kind of palette mechanism is beyond improving?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove the bellows...
« Reply #7 on: August 24, 2013, 11:19:53 PM »

How to tune reeds is something that is subject to all sorts if discussions, but basically you remove metal fear the tip to raise the pitch, and from about 2/3ds of the way down to lower it.  Look at the reeds and you will probably see the markes made by the tuner in the factory.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to remove the bellows...
« Reply #8 on: August 25, 2013, 07:29:57 AM »

How to tune reeds is something that is subject to all sorts if discussions, but basically you remove metal fear the tip to raise the pitch, and from about 2/3ds of the way down to lower it.  Look at the reeds and you will probably see the markes made by the tuner in the factory.
Hi.. Really grateful for all the advice. I think I understand how to alter the pitch of a reed. The bit I don't get is how to get at the reeds on the underside of the reed plate in order to make any adjustments. I mean the ones you can only see through the slots. Do I set up a tuning rig with bellows (I seem to have several decent sets of bellows..) and temporarily attach the plate so I can get at these reeds I.e. before I rewax the plate back into its proper place.
As I say - you guys are great. Thx again.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove the bellows...
« Reply #9 on: August 25, 2013, 10:54:51 AM »

Here are some photos of how I do it https://www.facebook.com/media/set/?set=a.498005193166.268921.709188166&type=1&l=00fc5e70cc

But on the very fragile brass reeds used in old Saxony instruments like yours I think there would be a risk of damaging the reeds.  You could use the Italian hook method, which I don't have pictures of.  You make the tool from a short length of spring wire or something like .6 or .7mm.  bend one end into the shape of a walking stick handle where the width of the bend equals the distance between centres of the push and pull reeds, fit the other end into a piece of dowel to form a handle.  To use it insert the hook under the top reed and twist it round so that the bent end lifts the underside reed, when the reed tip shows then slip a support plate under the reed.

Your reeds probably were not originally fitted with any wax.   The horrible gunge round them now is something added later.  They will be sitting on a gasket made of candlewick laid round all the edges which require sealing.  Wax doesn't work for long plate reeds because there is no way to get the vital seal between adjacent reed chambers.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove the bellows...
« Reply #10 on: August 25, 2013, 11:06:38 AM »

The hook tool is shown in this facebook album if you are able to see it
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to remove the bellows...
« Reply #11 on: August 25, 2013, 01:46:40 PM »

Here are some photos of how I do it https://www.facebook.com/media/set/?set=a.498005193166.268921.709188166&type=1&l=00fc5e70cc

But on the very fragile brass reeds used in old Saxony instruments like yours I think there would be a risk of damaging the reeds.  You could use the Italian hook method, which I don't have pictures of.  You make the tool from a short length of spring wire or something like .6 or .7mm.  bend one end into the shape of a walking stick handle where the width of the bend equals the distance between centres of the push and pull reeds, fit the other end into a piece of dowel to form a handle.  To use it insert the hook under the top reed and twist it round so that the bent end lifts the underside reed, when the reed tip shows then slip a support plate under the reed.

Your reeds probably were not originally fitted with any wax.   The horrible gunge round them now is something added later.  They will be sitting on a gasket made of candlewick laid round all the edges which require sealing.  Wax doesn't work for long plate reeds because there is no way to get the vital seal between adjacent reed chambers.

Hi, yes there is candlewick or something similar just visible. Thx for description of the Italian hook method.  I'll remove the reed plate to revalve and see how I get on. :)
As you probably know, the palette levers (or whatever they are called) on these Saxony boxes are pretty crappy - looks like copper wire with the palettes attached with little tacks. I need to make sure I can get then working with at least marginal efficiency otherwise there is no point in messing around with the reeds... :)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove the bellows...
« Reply #12 on: August 25, 2013, 02:46:27 PM »

Good luck with the levers. I've not worked out any way to improve those.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: How to remove the bellows...
« Reply #13 on: August 25, 2013, 03:26:05 PM »

You could use the Italian hook method, which I don't have pictures of.  You make the tool from a short length of spring wire or something like .6 or .7mm.  bend one end into the shape of a walking stick handle where the width of the bend equals the distance between centres of the push and pull reeds, fit the other end into a piece of dowel to form a handle.  To use it insert the hook under the top reed and twist it round so that the bent end lifts the underside reed, when the reed tip shows then slip a support plate under the reed.

Excellent description! They say pictures speak louder than words but you did it eloquently!
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: How to remove the bellows...
« Reply #14 on: August 25, 2013, 03:34:33 PM »

The hook tool is shown in this facebook album if you are able to see it

Not visible Theo :-(
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Reed tuning
« Reply #16 on: August 25, 2013, 07:08:33 PM »

There is a brief shot of a tuner using the hook to lift inside reeds at about 26mins into in this YouTube video of accordions and bandoneons being made in the Pigini factory.

There is also a lot(!) of reading about tuning, plus pictures of methods and tools, in the 3rd repair section of the Accordion Revival website.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reed tuning
« Reply #17 on: August 26, 2013, 07:25:15 AM »

There is a brief shot of a tuner using the hook to lift inside reeds at about 26mins into in this YouTube video of accordions and bandoneons being made in the Pigini factory.

There is also a lot(!) of reading about tuning, plus pictures of methods and tools, in the 3rd repair section of the Accordion Revival website.
Hi thx. Yes I've seen that site.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal