Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Leaky HA114  (Read 3199 times)

0 Members and 1 Guest are viewing this topic.

aislingean

  • Member
  • *
  • Offline Offline
  • Posts: 8
Leaky HA114
« on: September 01, 2013, 10:38:40 PM »

I have an air hungry HA114 in G that has leaks in the growl box  chambers on push.
The fixing screws for the growl box are below the timber reed blocks that are glued in.
Is there a recommended method for resealing through the spoon holes. ?????
Wax, Liquid resin, PVA, Alphatic resin, bead of silicone sealant, decorators acrylic caulk ????
The end-plate under the strap appears to be housed in a groove and can flex slightly.
Existing sealant has cracked and left a fingernail gap!
I imagine this is a fairly common problem on these older Hohners.
All suggestions gratefully received.
cheers
Dave

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Leaky HA114
« Reply #1 on: September 01, 2013, 11:08:38 PM »

The get access to the screws just remove the reeds and the screws are usually then accessible.

I would not recommend attempting to seal through the spoon holes, too much risk of getting sealant where you don't want it - on the reeds especially, and not being able to reach all the leaking joints.  I'm not clear from your description where the leaks are from, but if it is the joint between the growl box and the plate it mounts onto then it is not a big job to take of the reeds, remove the screws, take of the growl box and replace the gasket, then re-assemble.  Its always better to do the job properly first time.

The most common area of leaking on these is from the bass spoons themselves, and if it is mainly leaking on push then that is by far the most likely source of leaks.  To fix make sure you have:

The spoons lying completely flat when closed (they easily get bent)
good quality springs (they can break and may have been replaced with poor substitutes)
good pad material on the spoons (the original stuff gets hard)

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

aislingean

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Leaky HA114
« Reply #2 on: September 02, 2013, 12:10:41 AM »

Thanks Theo!
From here on I am 'Thinking out loud'
One screw is definitely under the base chord block timber! [The edge of the head is just discernible]
Two screws I can see and one is probably accessible under the single note reed-plate but the air leak is definitely between the grooved sides of the growl box and the strip of timber that sits in the grooves and forms the end/base of the box under the strap.
Two spoons are new and all have been checked and are sitting flat.
Holding spoons lightly closed and gentle push gives jet of air that can be felt on face or hand.
Bellows is airtight and treble side has no leaks.
Straps off ....suspend box .....bellows extends as there is only small  vacuum
Growl box to [silver papered] end plate is air tight.
I had thought that as the reeds will be above the work area it would be safe to work though the spoon holes.
I was reluctant to disturb the reed plates un-necessarily and had envisaged working with a syringe and flexible tube outlet to position sealant along the original joint line.
I favoured non acidic silicone as it will have a degree of structural adhesion and will flex with the timber but pouring wax or resin would seal the joints and alphatic would sink into the open joint and give structure but it has no gap sealing properties.
Hot glue either traditional or synthetic would not be as controllable, whereas Pva would whilst being controllable require a long curing time and would collect dust as it retains a surface tack. The acrylic caulk would seal any gaps and being easily reversible may be the best route to try at first but it will give no improvement in structure.
I had thought that this repair would have been a common one with a 'standard' solution'
Never mind I am on a voyage of discovery
cheers
Dave
 

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Leaky HA114
« Reply #3 on: September 02, 2013, 08:08:51 AM »

Now I understand where the leak is.  I've not  previosly seen an air leak in this location.  I would still favour removing the growl box, shaving some wood off the reed chambers if necessary to reach fixing screws. I would probably favour a bead of pva along the joint, applied from the inside. If I could only work from the outside I think I might use superglue which has the advantage of a capillary action that draws it into the cracks.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

aislingean

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Leaky HA114
« Reply #4 on: September 02, 2013, 01:21:45 PM »

I will report back after she is completed however I am in no rush  so don't hold your breath!
Logged

aislingean

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Leaky HA114 update
« Reply #5 on: September 05, 2013, 08:37:20 PM »

I have removed the reedplate and carved the reedblock side to expose the hidden screws only to find that when the screws are removed the growl box is firmly glued to the end plate and is not going to be removed without considerable force. [or perhaps a hot air gun]  :(
I had understood that they were simply screwed in place and sealed with a gasket.
Back to the original plan it seems.
I intend adding some skiver leather to the spoon pads when I re-assemble  but meantime I will seal the growler with automotive overlap seam sealer as it will brush and is very controllable! [I am doing a test piece first just to be safe  :-\ ]
Paul if you read this PM me please as I forgot your name on here!
Logged

aislingean

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Leaky HA114
« Reply #6 on: October 03, 2013, 04:00:19 PM »

Everything is now Hunky Dory with this G beasty!

All joints glued. Spoons re padded with funky foam and set level  recess in growlbox filled level with Black funky foam and black stop pads under spoon ends Reeds waxed in place

She feels and plays and looks a whole heap better now it's decision time .....
If I am going to sell this will it sell better with the button travel limited or should I leave it for the new owner to decide ????
Cheers
Dave  :-\
Logged

Cam Button

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Leaky HA114
« Reply #7 on: February 21, 2019, 03:58:57 AM »

What is the gasket in between the growler box, and the plate made from? I have to repair my spoons, but one of the screw holes is stripped out so the screw will not tighten. I was thinking of putting a bit of pva on the screw during installation to retain the screw.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Leaky HA114
« Reply #8 on: February 21, 2019, 07:46:59 AM »

You can use the same material that is used for bellows gasket, the 2mm thick stuff is best.

I’ve never tried ova to get a screw to grip, but I don’t think it would work.  I glue in the tip of a cocktail stick and for speed I use cyanoacrylate.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Cam Button

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Leaky HA114
« Reply #9 on: February 21, 2019, 03:39:16 PM »

Thank you
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Leaky HA114
« Reply #10 on: February 21, 2019, 05:58:35 PM »


I’ve never tried ova to get a screw to grip,

One assumes PVA was intended here...  ::)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal