Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Making an air release a bit taller ??  (Read 1859 times)

0 Members and 1 Guest are viewing this topic.

Harp2

  • Good talker
  • **
  • Offline Offline
  • Posts: 81
Making an air release a bit taller ??
« on: September 18, 2013, 06:59:44 PM »

Anyone got any good ways of extending a hohner type air release to make it stick up a bit more?
Logged

tekyinblack

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
Re: Making an air release a bit taller ??
« Reply #1 on: September 18, 2013, 07:01:26 PM »

Short piece of rubber or plastic tube?
Logged
Castagnari Sander D/G, Hohner Club III D/G, Hohner Liliput Eb/Bb, Hohner Club II C/F

Sage Herb

  • Steve Harrison
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 762
  • Slaithwaite, UK
    • The Black Box Band
Re: Making an air release a bit taller ??
« Reply #2 on: September 18, 2013, 10:04:27 PM »

I have on several occasions edged the button a little further off the lever. It didn't appear to be glued, but you have to be careful. I did once break the button but replaced it with the end of one of those tiny cheap ball pens that they give away in bookmakers and bingo - you pick these pens up in the street. But surely Theo will be along with better advice.

Cheers
Steve
Logged
Hohner Erikas & Club 2s
Hohner gob-harps:
Vega Senator 5-string banjo; Alex Burns plectrum guitar

Black Box Band - www.theblackboxband.co.uk
Annie Dearman & Steve Harrison - www.dearmanharrison.co.uk
Phoenix - www.phoenixdanceband.co.uk
http://soundcloud.com/sage-herb

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making an air release a bit taller ??
« Reply #3 on: September 18, 2013, 10:15:10 PM »

The plastic lever is a tight push fit on the lever. Replacements are available!  If you want a longer version then some accordion bass buttons are suitable.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Harp2

  • Good talker
  • **
  • Offline Offline
  • Posts: 81
Re: Making an air release a bit taller ??
« Reply #4 on: September 18, 2013, 10:33:16 PM »

Thanks for the tips.
The plastic button is actually quite long but unfortunately most of it is inside the box and its not wanting to slide up the wire/lever for me.
Ideas welcome ??
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making an air release a bit taller ??
« Reply #5 on: September 19, 2013, 07:54:39 AM »

You will have to remove the bass end plate to get access to the button, and you might also need to remove the air valve mechanism to get a good grip on things.  If you do this remember to release the spring before undoing the screws.    Once out you could try dipping the button into hot water to soften it slightly.

I wonder if the bass end plate is properly fitted?  If it is not fully seated into the rebate round the end of the case then the air button will appear low.  Or has the bass end plate been replaced?  Some are thicker than others.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Making an air release a bit taller ??
« Reply #6 on: September 19, 2013, 08:42:52 AM »

I found this a problem when I started but like a lot of things with Hohners with time and practice the problem seems to go away, I do still think from time to time that the air lever could be a bit further down the box but I do have small hands.
Logged
aka malodeon

MartinW

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 202
Re: Making an air release a bit taller ??
« Reply #7 on: September 19, 2013, 11:09:27 PM »

I found that I prefer the air button to protrude slightly further than the original metal feet on my Hohners. This meant fitting longer feet. Otherwise, when I pulled the button out to a suitable position, setting the melodeon on its end pushed the button back in again.

Martin
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal