Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Pallet facings  (Read 4974 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Pallet facings
« on: September 26, 2013, 05:11:51 PM »

Maybe a silly question, but after a day at work...

It has previously crossed my mind that sound emerging from a box immediately hits the pallets, faced with soft stuff, as Microbot has observed on the "Muffled" thread.

So could one fit the facing on the soundboard, leaving the pallet surface clear to reflect the sound? And slightly lighter. It would be necessary to cut holes to clear, of course.  ::)

Is there any reason, beyond convenience, for putting the felt/leather on the pallet surface?
« Last Edit: September 26, 2013, 10:46:17 PM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Pallette facings
« Reply #1 on: September 26, 2013, 07:04:05 PM »

hmmm ... interesting!

I suspect it's to do with using less of the pallet padding material in the first place and keeping the cost down ... but there's probably the "it's always been that way" reason too.  Maybe it should be tried!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Pallette facings
« Reply #2 on: September 26, 2013, 07:26:06 PM »

On the face of it (ahem) it seems like a brilliant idea and I wish I'd thought of it. But I suspect it would be a lot more fiddly to cut holes out of the padding material than to trim it around a nice hard shape. 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallette facings
« Reply #3 on: September 26, 2013, 07:41:25 PM »

I think Steve has a point, though that would not make it impossible, just a little more work.

Another possible reason is to do with the way the facing material in the conventional position forms itself by bulging slightly into the hole.  This might possibly form a better seal than having the gasket on the board.

Another option for reducing muffling is to use the smooth face of the leather as the sealing surface.  This is the normal practice with concertina pads.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Pallette facings
« Reply #4 on: September 26, 2013, 07:56:48 PM »

Maybe a silly question, but after a day at work...

It has previously crossed my mind that sound emerging from a box immediately hits the pallettes, faced with soft stuff, as Microbot has observed on the "Muffled" thread.

So could one fit the facing on the soundboard, leaving the pallette surface clear to reflect the sound? And slightly lighter. It would be necessary to cut holes to clear, of course.  ::)

Is there any reason, beyond convenience, for putting the felt/leather on the pallette surface?

Malcolm,

After thoroughly enjoying that cider video, this is the second time today I'd like to thank you.

What an interesting idea.

And you know, I've just seen two examples of something similar to what you suggest, but it didn't occur to me that your idea might have been the reason. 

One was an early wooden-finish Globe 6-voice Gold Medal Professional box.  Sort of like a 4 stop but with 6 voices and no stops.  That box as you might guess has very long pallets.  The surface of the soundboard of that box, on which the pallets close,  was covered with a layer of cork perforated for the 6 airways per pallet.  I thought it might be to quiet the slap of those long pallets, or maybe to seal the soundboard if it might have cracks, but in fact it could function as you suggest.

The second example was the later model of Globe 6-voice Gold Medal Professional De Luxe.  This is a celluloid-covered box with the pallets enclosed under a metal grille.  Here, IIRC, a big piece of leather was laid on top of the aluminum soundboard under the pallets.  As with the cork in the example above, this was drilled with holes for the airways. Again I speculated the reason might have been to quiet the slap of pallets after the original pallet facing had hardened.

Will take another look at that last example and post a photo.

PG
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Pallette facings
« Reply #5 on: September 26, 2013, 08:00:54 PM »

 :|bl
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallette facings
« Reply #6 on: September 26, 2013, 08:02:26 PM »


What an interesting idea.

And you know, I've just seen two examples of something similar to what you suggest, but it didn't occur to me that your idea might have been the reason. 


I've seen similar on some Hohner Club models, but only on the bass end, where there is a layer of leather on both the pallets and the board.  No idea why!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallette facings
« Reply #7 on: September 26, 2013, 08:05:41 PM »

BTW I don't think Pallette is correct.  Palette is used for a collection of colours as in a painters palette, or make-up palette, but in our context it just has one t and no final e. 

A pallette is found in the armpit of a suit of armour!  8)
« Last Edit: September 26, 2013, 08:09:12 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Pallette facings
« Reply #8 on: September 26, 2013, 08:26:30 PM »

Hi all,

Having thought about this a little more, I wonder if you might lose on the reflected sound off the soundboard. 

In other words, the net effect of leather or cork on the soundboard (especially inside an enclosed action area, under a treble grille or in the bass machine of the clubs that Theo mentioned) might be to mute the high harmonics, as well as cushioning the pallet slap.

With that in mind, how about bare pallets (wood or metal) and a bare soundboard (wood or metal), but a little rubber "O ring" (but shaped like a rectangle with slightly rounded corners) affixed to the just the very periphery of the flat surface of each pallet to make a seal around each?

PG
« Last Edit: September 26, 2013, 08:31:10 PM by pgroff »
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Pallette facings
« Reply #9 on: September 26, 2013, 10:52:45 PM »

BTW I don't think Pallette is correct.  Palette is used for a collection of colours as in a painters palette, or make-up palette, but in our context it just has one t and no final e. 
Agreed - I was in a rush and spellchecker playing up. Been annoying me - now amended (:)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Etienne

  • Student in push-pull things
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 186
    • ça s'pousse et ça s'tire
Re: Pallette facings
« Reply #10 on: September 26, 2013, 10:56:38 PM »

BTW I don't think Pallette is correct.  Palette is used for a collection of colours as in a painters palette, or make-up palette, but in our context it just has one t and no final e. 

A pallette is found in the armpit of a suit of armour!  8)

In french it's ok, "une palette" can be a lot of things, even "a melodeon palet", but for a "melodeon palet" the more common word in use is "soupape" and that's mean "valve", but what is call a "valve" in english is the little piece of leather or plastic on the reed and that is call a "peau" in french and that's mean "leather" or "skin" in english... Very confusing, I don't know why I tell tou that.
Logged
Old hohner and old Dedenis
http://pousser-tirer.blogspot.com

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Pallet facings
« Reply #11 on: September 26, 2013, 11:43:16 PM »

But returning to English in which the original was written ... pallet is the correct spelling for the bit on the other end of a lever from the button which opens the aperture to allow the air to pass over the reed being played.  It is also the correct spelling for the platforms made of uniform size to support industrial quantities of most things specifically in order that a fork-lift truck can pick them up easily - an object, often discarded by the trade with which I also make my allotment compost bins!

Palette is the correct spelling for the device from which an artist chooses which paint colour to dip his brush in and by inference a spectrum of colours or any other primary building blocks.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Pallet facings
« Reply #12 on: September 26, 2013, 11:52:18 PM »


Palette is the correct spelling for the device from which an artist chooses which paint colour to dip his brush in and by inference a spectrum of colours or any other primary building blocks.

Probably a Freudian slip reference to my language when I can't get a phrase right.

Returning to our sheep, it did cross my mind that a neoprene or similar gasket around each hole might do the job. Unless you have the wherewithal to punch a single strip out of  sheet material.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Pallette facings
« Reply #13 on: September 27, 2013, 12:09:40 AM »

Hi

With that in mind, how about bare pallets (wood or metal) and a bare soundboard (wood or metal), but a little rubber "O ring" (but shaped like a rectangle with slightly rounded corners) affixed to the just the very periphery of the flat surface of each pallet to make a seal around each?

PG

Ha! We are talking Chansonese now!
By the way I've permanently rusticated myself and feel better for it.
Signed, a Bb/Eb Lilliput owner.  ;D
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Pallet facings
« Reply #14 on: September 27, 2013, 12:46:52 AM »

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallet facings
« Reply #15 on: September 27, 2013, 06:58:26 AM »

Quote from: malcolmbebb link=topic=13259.msg163093#msg163093 date

 Unless you have the wherewithal to punch a single strip out of  sheet material.

Not necessary.  Just stick the material down and the  cut the holes with a scalpel, using the holes in the wood as a guide.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Pallet facings
« Reply #16 on: September 27, 2013, 07:59:08 AM »

Not my field, but what do the "posh" boxes, ie custom made by more obsessive luthiers formore obsessive clients use? Though that's not to say such use implies it is "to the good" ;)
Logged
  _       _    _      _ 

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Pallette facings
« Reply #17 on: September 27, 2013, 08:29:31 AM »

I think Steve has a point, though that would not make it impossible, just a little more work.

Another possible reason is to do with the way the facing material in the conventional position forms itself by bulging slightly into the hole.  This might possibly form a better seal than having the gasket on the board.



Where's the Agree button?  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Pallet facings
« Reply #18 on: September 27, 2013, 08:51:35 AM »

"Another possible reason is to do with the way the facing material in the conventional position forms itself by bulging slightly into the hole.  This might possibly form a better seal than having the gasket on the board."

Assuming that the contact area and the compliance of the material is the same there will be only a small difference, due to the perimeter of the seal area, in the sealing force. I think that if you are making large numbers of instruments then cost and speed of assembly will be less with conventional construction.
As it happens when I first got my old Erica, long before Melnet and driven mad by the noise I stuck a sheet of thin soft leather over all the holes and as Theo said cut round with a Scalpel, it is still going fine.
Logged
aka malodeon

DaveD

  • Good talker
  • **
  • Offline Offline
  • Posts: 82
Re: Pallet facings
« Reply #19 on: December 24, 2013, 05:17:14 PM »

"Not my field, but what do the "posh" boxes, ie custom made by more obsessive luthiers for more obsessive clients use? Though that's not to say such use implies it is "to the good" ;)"

Just interested if anyone knows the answer to Chris's question, what material do the more expensive manufacturers use for pallet facings, only that I have an annoying 'pallet slap' developed on a single bass pallet.

Dave
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal