Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Pallet facings  (Read 4963 times)

0 Members and 1 Guest are viewing this topic.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Pallet facings
« Reply #20 on: January 01, 2014, 04:02:50 PM »

"Not my field, but what do the "posh" boxes, ie custom made by more obsessive luthiers for more obsessive clients use? Though that's not to say such use implies it is "to the good" ;)"

Just interested if anyone knows the answer to Chris's question, what material do the more expensive manufacturers use for pallet facings, only that I have an annoying 'pallet slap' developed on a single bass pallet.

Dave

I use special pallet leather as supplied by Russells. They provide parts for organ builders. It is very expensive.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallet facings
« Reply #21 on: January 01, 2014, 04:06:16 PM »

I use special leather supplied by Carini for accordion builders!  It is not quite so expensive.  Better quality boxes usually have a thicker layer of felt under the leather which also helps keeping the noise down.  Big PAs oftern have a 5 or 6mm felt layer.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Online Online
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Pallet facings
« Reply #22 on: January 01, 2014, 04:11:44 PM »

IIRC Rees uses quite thick felt behind the leather?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallet facings
« Reply #23 on: January 01, 2014, 04:22:08 PM »

Of course, he he is a builder of high quality instruments.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Online Online
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Pallet facings
« Reply #24 on: January 01, 2014, 04:37:07 PM »

 ;D
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Pallet facings
« Reply #25 on: January 01, 2014, 07:38:34 PM »

Thicker felt will help you get a better seal on those 4 reed jobbers too.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Pallet facings
« Reply #26 on: January 04, 2014, 03:58:18 PM »

The sealing material on the spoon basses of a four-stop Hohner certainly takes on an impression of the hole, giving a perfect fit and seal when the lever stays aligned.  Strangely, one day mine decided to go awry and all the bass reeds groaned away continually.  Even stranger, after a bit of wiggling and flicking, they realigned themselves and never failed again...?!

I would guess that once the impression is established, a slight misalignment will be corrected as the spring pulls the lever shut but beyond a certain tolerance it just sits cracked open.  I wonder what impression a pallet would make on a continuous sheet of facing and whether it would work toward maintaining the alignment and sealing or start to leak as it hardens.  Mind you, it should be easier to replace than fiddling around with individual bits on each pallet.

Rob.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Pallet facings
« Reply #27 on: January 04, 2014, 04:02:10 PM »

The sealing material on the spoon basses of a four-stop Hohner certainly takes on an impression of the hole, giving a perfect fit and seal when the lever stays aligned.  Strangely, one day mine decided to go awry and all the bass reeds groaned away continually.  Even stranger, after a bit of wiggling and flicking, they realigned themselves and never failed again...?!

I would guess that once the impression is established, a slight misalignment will be corrected as the spring pulls the lever shut but beyond a certain tolerance it just sits cracked open.  I wonder what impression a pallet would make on a continuous sheet of facing and whether it would work toward maintaining the alignment and sealing or start to leak as it hardens.  Mind you, it should be easier to replace than fiddling around with individual bits on each pallet.

Rob.

Replacing the cardboardy stuff on a 4 stop with Charlie's best makes them infinitely quieter. The first mod on any one that comes through my hands.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Pallet facings
« Reply #28 on: February 04, 2014, 04:54:17 PM »

On instruments with no real adjustment for thicker valve facings, I use some 3mm elk suede that I got somewhere. Very soft and flat, and one side is smooth and fuzzy, that side goes against the hole. Quiets a pokerwork way down.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal