Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Wiring Internal mics (split from seeing posh box being built)  (Read 4161 times)

0 Members and 1 Guest are viewing this topic.

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Wiring Internal mics (split from seeing posh box being built)
« on: September 28, 2013, 05:18:52 PM »

As mentioned this stage was a bit of a surprise for me; when nudiefish asked me to fit a “mike system” I just said, “yes” without thinking much about it.
When I came to start to fit it I came to the very fast conclusion that I had never put one into this smaller size box (240mm x 150mm) that had 12 bass and slides, this causes the reed blocks to take up every last mm within the bellows cavity giving me very little room to move for the cabling down the inside of the bellows, eventually after a very frustrating day I got there with it.

Because of the 12 bass in such a small box I even had to put the stereo socket in a place where I would not normally do so, this time I had to have it fit within the bass mechanism rather than bellow it.
If I ever have to do this again on this size box, then I would run the first half of the cabling across the back folds then revert to the top for the next half.
After the initial frustration it works very well.

This interested me as the cabling looked very fiddly and I got to thinking why not create a frame (maybe thin aluminium to keep weight down) that sits inside the bellows to center the cable and then use a spiral cable that would expand with the bellows. I tried to create a small drawing to illustrate whet I mean. Putting plugs on both ends of the cable, to connect with sockets in the reed boxes would help with tuning to detach the bellows completely.
« Last Edit: September 30, 2013, 07:50:18 AM by Theo »
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

Peter Stormy Hyde

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 143
    • Hyde Accordions
Re: Re: See
« Reply #1 on: September 29, 2013, 05:54:49 AM »

As mentioned this stage was a bit of a surprise for me; when nudiefish asked me to fit a “mike system” I just said, “yes” without thinking much about it.
When I came to start to fit it I came to the very fast conclusion that I had never put one into this smaller size box (240mm x 150mm) that had 12 bass and slides, this causes the reed blocks to take up every last mm within the bellows cavity giving me very little room to move for the cabling down the inside of the bellows, eventually after a very frustrating day I got there with it.

Because of the 12 bass in such a small box I even had to put the stereo socket in a place where I would not normally do so, this time I had to have it fit within the bass mechanism rather than bellow it.
If I ever have to do this again on this size box, then I would run the first half of the cabling across the back folds then revert to the top for the next half.
After the initial frustration it works very well.

This interested me as the cabling looked very fiddly and I got to thinking why not create a frame (maybe thin aluminium to keep weight down) that sits inside the bellows to center the cable and then use a spiral cable that would expand with the bellows. I tried to create a small drawing to illustrate whet I mean. Putting plugs on both ends of the cable, to connect with sockets in the reed boxes would help with tuning to detach the bellows completely.

g'day syale; I can definitely see where you are coming from as the drawing is self explanatory, this has got to be worth looking at.
 I have been asked to do the same job on a like minded box, so I will be running with the same problems.

The only problem i can see so far is that the little coils would mean there will be a lot of cabling moving around that is not anchored, and could end up between the reed blocks.

When I start the next job I will start with your suggestion in mind and see where it takes me.
The one thing I have learn t is that all things have to be tried  even if you are 100% sure they are not going to work, as the process opens the mind to other possibilities that you did not see before.
Thank you for the loan of your Gray Cells.
Logged
"Locally Made; Globally Played". Truly custom made melodeons. your total needs are met in the construction of your personalized instrument. People with physical disabilities are catered for as far as possible.

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Re: See
« Reply #2 on: September 29, 2013, 06:22:42 PM »

About the question that is discussed here at the moment:
"The only problem i can see so far is that the little coils would mean there will be a lot of cabling moving around that is not anchored, and could end up between the reed blocks."

I also would think so, but one could give it a try. I think the distance between one side and the other of the bellows frame is  not long enough for the collapsed  coil. First one would need a nice wire coil with the amount of wires in it as the are needed.
How many single wires are in it?
Is such a coil available somewhere?
Will the coil keep its springiness over time?
I am also not sure if the wire will finaly with fast bellows movement still get caught?


Audio microphone spiral cables are available (http://www.ebay.com/itm/Monacor-CCX-5M-Microphone-Spiral-Cable-/321200351474?pt=LH_DefaultDomain_0&hash=item4ac90868f2). With the cable centred using a bracket, if you ensure that the cable is already under tension between the bellows at rest and the cable will extend to the distance with the bellows pulled out, I doubt it would foul the bellows folds. If the reeds extend into the bellows then bend the frame into the bellows also so it sits above the reeds at rest.

Stephen
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Re: See
« Reply #3 on: September 29, 2013, 06:25:49 PM »

I just though of another thing to do is to have a piece of elastic braid running down the centre of the coils attached to the frame for a 'belt and braces' method. The elastic could be changed out if needed.
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Re: See
« Reply #4 on: September 29, 2013, 08:05:16 PM »

I have such microphone cable, but this is not suitable from my viewpoint.
"Mikrofon-Spiralkabel Monacor CCX-5M, Mikrofon-Spiralkabel, Ø 5 mm, 2-adrig, Symmetrisch in einem Schirm, 80-500 cm lang"

Are we talking a bout a microphone cable or MIDI connections?
Microphone cabling can be with very little cross section, so special coils with bigger coil cross section diameter and thinner wire cold solve the problem if such springy stuff is available.
My be in some boxes where is a lot of distance from one bellows frame to the other.
Or one mounting point is more near the top of the frame and the other closer to the bottom, so the distance from one side to the other for the spiral wire is more as shown on the drawing.
But i am still not convinced.
--------------------------------------------
But i think this gets here out of topic.
« Last Edit: September 29, 2013, 08:28:52 PM by JohannPascher »
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Re: See
« Reply #5 on: September 29, 2013, 08:33:58 PM »

I just thought of another thing to do is to have a piece of elastic braid running down the centre of the coils attached to the frame for a 'belt and braces' method. The elastic could be changed out if needed.

I've been watching this thread with interest as I wired the inside of my Oakwood bellows, not very elegantly at all, and wondered how it could be done better. I have to say that is one of the best ideas I have seen. Done right, it should keep the centre of the spiral in a straight line and prevent it from fouling on the reed blocks or the bellows. You'd need very good elastic though, able to stretch to at least 4x original length without too much increase in tension.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Re: See
« Reply #6 on: September 30, 2013, 01:48:02 AM »

I've been watching this thread with interest as I wired the inside of my Oakwood bellows, not very elegantly at all, and wondered how it could be done better. I have to say that is one of the best ideas I have seen. Done right, it should keep the centre of the spiral in a straight line and prevent it from fouling on the reed blocks or the bellows. You'd need very good elastic though, able to stretch to at least 4x original length without too much increase in tension.

Found this: http://www.hobbyking.com/hobbyking/store/__10329__hobbyking_6mm_silicon_rubber_bungee_hi_start_cord.html

Silicon rubber Bungee Cord stretches to 6 times its original length and is light weight giving a consistent pull, great for gliders and EDF jets of up to 3kg.
 
Spec.
Length: 10m
Outside diameter: 6mm
Inside diameter: 4mm 
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: Re: See
« Reply #7 on: September 30, 2013, 03:39:56 AM »

Modified picture for microphone cabling.

Colour - Silver: can be aluminium or wood frame to center cable in bellows
Colour - Red: Elastic braid or silicone rubber tube
Colour - Black: Spiral wound cable
Colour - Purple: cable ties to secure cable
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Re: See
« Reply #8 on: September 30, 2013, 07:21:26 AM »

OK someone my test this.
Still not convinced.
------------------------------------------------------------------------------------------------------
PS: The Moderator my move this subject about the mic wiring to a other thread because is is totally out of scope in this thread.
done
« Last Edit: September 30, 2013, 08:59:35 AM by JohannPascher »
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Wiring Internal mics (split from seeing posh box being built)
« Reply #9 on: September 30, 2013, 11:09:05 AM »

I am not convinced that any coil will work. Well, that is to say it would work well for a grandma playing a PA but any boisterous movement which is not uncommon with a melodeon will be transmitted to the coil which will slap against the bellows - a novel percussion effect.

The only internal wiring of which I have personal experience was a serpentine (each bend above or below the fixing point so as to work in conjuncion with the bellows).  At each intersection with the inner folds of the bellows the wire was attached with the smallest possible dab of silicone - the only failing was that there were no connectors at the ends of the bellows making repairs a delicate issue.

Rob.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Wiring Internal mics (split from seeing posh box being built)
« Reply #10 on: September 30, 2013, 11:29:37 AM »

Interesting, and I've put a link here in the 21st Century Box thread. I too can see issues. It may not be stable as per above. Also in bigger kit there is often virtually no space between end reed blocks with bellows closes (some=nil!). That makes for a big change in length of your coil, and also a force pulling bellows in that'll change as you expand them.

  "Hooke's Law", if memory serves me right? ;)

Great idea to internalise, and only one plug. Does it need to be a coil though? With modern materials one might take a couple of very flexible wires zig-zag inside the bellows themselves?
Logged
  _       _    _      _ 

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Wiring Internal mics (split from seeing posh box being built)
« Reply #11 on: September 30, 2013, 04:34:45 PM »

in bigger kit there is often virtually no space between end reed blocks with bellows closes (some=nil!). That makes for a big change in length of your coil

Yes, if that's what was proposed. I'd want to make the ends of the wire/elastic as far apart as possible, i.e. at the inside faces of the pallet board.

Quote
one might take a couple of very flexible wires zig-zag inside the bellows themselves?
two strips of conductive self-adhesive tape following every internal pleat of the bellows? Fascinating - I wonder how long it would last, and how much interference it would pick up.

Radical alternative: ultra low-power Bluetooth link?
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Wiring Internal mics (split from seeing posh box being built)
« Reply #12 on: September 30, 2013, 05:19:43 PM »

Radical alternative: ultra low-power Bluetooth link?
Yes this works well, but the sound quality my be to low for some applications.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal