Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner Valve Adhesive question  (Read 9611 times)

0 Members and 1 Guest are viewing this topic.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Hohner Valve Adhesive question
« Reply #20 on: October 14, 2013, 05:14:08 PM »

The guy at Hohner USA parts shop told me what they sold was Pliobond.  I got some, and like it for leather valves, but it melts the plastic valves I have (not from Hohner).  Hohner must use a different material for their plastic valves.

 I use pliobond , but it is important to use a VERY thin layer on the valve ,otherwise the valve may freak out.  This can be avoided by applying the adhesive to the valve ,putting it on the plate, remove it, wait a second then place it on. I believe this evaporates the solvents that cause problems. This seems to only be a problem with the smaller valves.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Hohner Valve Adhesive question
« Reply #21 on: March 20, 2014, 12:35:36 AM »

I use pliobond , but it is important to use a VERY thin layer on the valve ,otherwise the valve may freak out.  This can be avoided by applying the adhesive to the valve ,putting it on the plate, remove it, wait a second then place it on. I believe this evaporates the solvents that cause problems. This seems to only be a problem with the smaller valves.

 Have just tried out Pliobond on some CGM plastic valves. The adhesive was packaged in a tube, bought locally at the hardware store, and is an amber colored liquid. The adhesive was applied to clean zinc plates, and then a coat to the valve. After waiting about 5 minutes, I pressed the valve in place, and let it sit for another 20 minutes or so. Then I went about testing the adhesion of the valve, and if ok, I would then trim the tip. Here are my totally subjective and un-scientific observations:
 
  About 1 in 5 came loose. Most held well. The coating process is very tedious, as the product is loaded with very nasty and rapidly drying solvents (MEK, Formaldehyde Gas and some other equally friendly stuff >:E :-X >:E). You are trying to accurately place tiny amounts in very precise areas.
  Another after-affect:  the box will likely emit Pliobond fumes along with the sonorous tunes you are playing...this may continue for a few days.
  You will have to perform the work where there is some sort of ventilation, or exhaust fan close by, or you may slip into a strange mental state. (Don't ask)!
   On the plus side, the adhesive did absolutely no damage to the valves, which are probably a different sort of plastic than the ones that melt. In fact, I suspect that part of the adhesion problem I had was due to the fact that the glue did not bond or bite into the plastic. This might be improved by scuffing the finish of the plastic where the glue will be applied.
   In short, I found using this product to be tedious, unpleasant, time consuming, and unreliable. If anyone has had great results using it, I would love to learn your secret.
   For now, I will continue to use my stand-by:  Gorilla Glue  (the small super glue variety). It's more like a gel type, goes on quickly, allows repositioning time, and sets in 10-15 minutes, and the odor is quite less noxious.
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Hohner Valve Adhesive question
« Reply #22 on: March 20, 2014, 02:53:02 AM »

I didn't like the Pliobond, for a couple reasons.  I've been using Barge and like it better than anything I've tried so far.

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Hohner Valve Adhesive question
« Reply #23 on: March 21, 2014, 03:50:17 AM »

I use evo-stik multi-purpose impact from a tube.

I place a splodge on a small piece of plastic (well, it's a membership card for CEX, a second hand computer games amongst other gadgets, store) and smear the end of the valve through it. It allows some flexibility over how much is applied, and I can usually work quickly enough to get through 4 valve applications before it becomes too tacky to work witb any more. At this point it's easy to remove what's left on the card's plastic surface ready for the next splodge.
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner Valve Adhesive question
« Reply #24 on: March 21, 2014, 08:03:34 AM »

Another vote here for Bostik solvent-free contact adhesive. I've been using it for several years and have not had any problems  with valves subsequently falling off.

Like Theo and others have already mentioned, I use a cocktail stick to apply a thin smear of glue to the valve only and then press the valve in place immediately. There is a short time (10 seconds or so) to adjust the positioning before the glue gets tacky. Works well with leather, vileda (synthetic leather) or vinyl plastic valves. Does not dissolve the plastic. 

No-one has mentioned this yet but before affixing a new valve, I clean the end of the reed plate where the glue will go, using a cotton bud moistened with a drop of nail varnish remover. It degreases the reed plate and helps release any old glue residue which goes into rubbery threads or blobs which are easily removed with tweezers. A quick wipe clean with a dry cotton bud and it's ready to receive the new valve.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Hohner Valve Adhesive question
« Reply #25 on: March 21, 2014, 08:13:51 AM »

In a field emergency I've used reed wax a few times, just steal a small blob using a penknife blade, and press the valve onto it. It's remarkable how long valves stay put just using reed wax!
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Valve Adhesive question
« Reply #26 on: March 21, 2014, 09:12:01 AM »

Being serious for a change. This happened to me. Most venues have a first aid kit. Two pallets fell off during a wedding gig. All rescued by Elastoplast...... For an hour or so  ;D
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Valve Adhesive question
« Reply #27 on: March 21, 2014, 09:13:31 AM »

Like Theo and others have already mentioned, I use a cocktail stick to apply a thin smear of glue to the valve only and then press the valve in place immediately.

I've never done this.  Just apply the glue direct from the tube to the valve.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Valve Adhesive question
« Reply #28 on: March 21, 2014, 09:15:51 AM »

Typical. We're talking valves not pallets. Doh!  Evo stick is the stuff. Don't know the equivalent in the US.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner Valve Adhesive question
« Reply #29 on: March 21, 2014, 09:17:08 AM »

Like Theo and others have already mentioned, I use a cocktail stick to apply a thin smear of glue to the valve only and then press the valve in place immediately.

I've never done this.  Just apply the glue direct from the tube to the valve.

Me neither, about the only thing I learned from a dremel toting tuner bloke was to keep my glue tube stood upright in a small portable bench vice so I can just squeeze it and wipe the valve over the top of the tube.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner Valve Adhesive question
« Reply #30 on: March 21, 2014, 09:21:37 AM »

Strangely enough, that's about the only thing that I've learned from him too  ;)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner Valve Adhesive question
« Reply #31 on: March 21, 2014, 10:18:47 AM »

Like Theo and others have already mentioned, I use a cocktail stick to apply a thin smear of glue to the valve only and then press the valve in place immediately.

I've never done this.  Just apply the glue direct from the tube to the valve.
Sorry to confuse - I didn't mean to imply that you used a cocktail stick, but that you added the glue to the valve only.
But - I tend to be a bit heavy-handed with glue (in the words of Emmanuel: "does your father own ze glue factory?") and so I like the cocktail stick method as it gives me fine control.  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Hohner Valve Adhesive question
« Reply #32 on: March 21, 2014, 12:45:37 PM »

I have used Barge cement successfully too.  The only thing I don't like about it is that it is a little difficult to remove cleanly.  I always liked the way shellac cleaned off the plates so easily but it is difficult to prepare and use. I recently discovered a pre-prepared shellac adhesive sold in automotive stores as 'gasket shellac'.  I suspect it will work well also and be easier to remove.
Logged

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: Hohner Valve Adhesive question
« Reply #33 on: March 21, 2014, 12:52:56 PM »

32 replies on the matter of glue for reed valves. What a wonderful place this is!
 ;D
No wonder I couldn't stay away!
Tom
Logged

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Hohner Valve Adhesive question
« Reply #34 on: March 21, 2014, 01:02:07 PM »

Yes,  it helps you to stick around  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Hohner Valve Adhesive question
« Reply #35 on: March 21, 2014, 02:15:46 PM »

Am actually riveted to this thread. However, I think the valves are made of Mylar, in which case a contact adhesive would seem to be the answer, but not Copydex.
 By the way, what glue is used on Mouthorgan valves?
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal