Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: sticky key  (Read 8051 times)

0 Members and 1 Guest are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
sticky key
« on: October 19, 2013, 06:16:23 PM »

Ok so 60% to 70% humidity level lately and my fifth button is sticking some times, but enough to be annoying.
So I broke out the screw driver and pulled things apart and removed keyboard (on the Beltuna's the spring for the rocker
is under the wood rocker and not on the bottom attach like most of the Cajun brands I've seen with screws or nails) which releases all springs. All but three of the rocker levers move easily and those three seem to have a little less tolerance in the space where they sit. I was going to pull the pin or rod holding them in place but was surprised at how much force I needed and Yes I was twisting a little. It seems to twist but wasn't pulling out much and when twisting back and forth those same three levers where moving with the rod and now I think maybe the hole in the lever or rocker is tight. I also moved rocker back and forth 90 degrees a few times and this helped a little and it is playing now with out sticking but feel like to fix it right I need to pull the pin to enlarge the hole or sand the channel or rocker so everything moves freely.
Any Advise?
thanks

Edit: I should add I have a Beltuna one row four stop
« Last Edit: October 19, 2013, 06:25:42 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: sticky key
« Reply #1 on: October 20, 2013, 12:03:14 AM »

Is there enough axle sticking out to hold in the chuck of a cordless drill. If so, try revolving it very slowly as you pull it out. Beware, brass axles will snap, steel should be OK.

I have instructions in a book somewhere which advise connecting a car battery to each end of the axle. This a desperate measure which I have tried only once. Clouds of smoke ensued from a rather pretty Oakwood.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: sticky key
« Reply #2 on: October 20, 2013, 12:46:27 AM »

Yes there is plenty of axle to grab with pliers , I'm not sure if there's enough for drill though.
It looks like a steel rod to me and like I said it twist pretty easy. I just didn't want ruin anything.
moving the fifth button around did help as it not sticking now but I'm hearing a little bird chirping when I push the button
so it must be rubbing still. and I only have one end of axle sticking out so I can't burn my way out ( this method sounds counter intuitive as the heat wood cause the metal to expand)
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: sticky key
« Reply #3 on: October 20, 2013, 08:05:30 AM »

I only have one end of axle sticking out so I can't burn my way out ( this method sounds counter intuitive as the heat wood cause the metal to expand)

...which would widen the hole a little, then when the metal cools and contracts it's a looser fit.
Also the heat might dry out the wood making it shrink.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticky key
« Reply #4 on: October 20, 2013, 08:56:05 AM »

If keys are moving as you rotate the rod then either the hole in the wooden key is too small, or the rod surface has some roughness, or both.  When you get the rod out you can test for roughness by running your fingers along the rod and you will be able to feel any asperities.  These can be removed by gentle rubbing with very fine abrasive paper, I suggest 1200 grit.
When you've done this take each of the sticking keys and thread them onto the rod where they should swing freely.  If you do have to ream the hole be extremely cautious, it is very easy to remove too much wood and end up with a sloppy fit which will give the key a sloppy feel when playing. Sometimes it is sufficient to run the rod back and forth a few times through the hole. If that doesn't do it then a twist drill of the same size of the rod can be used IN THE FINGERS ONLY to team the hole. If you see the drill removing visible wood particles it is cutting too much. Take care.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: sticky key
« Reply #5 on: October 20, 2013, 09:23:15 AM »

I'm reminded of the time I couldn't get the brake pins out of the front wheel assembly of my motor bike. Took it down to a family friend, who had a garage in Jesmond Dene. Dave tried most of the tricks described above, or similar, and got no further than me. Then he muttered something about "sometimes a little gentle heat" … disappeared into the back.

It was an oxyacetylene torch! Worked, but was never quite as pretty again 
Logged
  _       _    _      _ 

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: sticky key
« Reply #6 on: October 20, 2013, 02:34:13 PM »

thanks for the replies
I probably give it another try but for now it's playing with out sticking.
but now I see why those buttons always felt a little stiffer than the rest and while I'm in there I'll see if I can fix the squeak
in button 6 spring.
I wonder if a soldering tool could heat the rod enough to free it up?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #7 on: October 20, 2013, 03:31:56 PM »

Is there enough axle sticking out to hold in the chuck of a cordless drill. If so, try revolving it very slowly as you pull it out. Beware, brass axles will snap, steel should be OK.

I have instructions in a book somewhere which advise connecting a car battery to each end of the axle. This a desperate measure which I have tried only once. Clouds of smoke ensued from a rather pretty Oakwood.

Now that would be a good stage trick :-)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #8 on: October 20, 2013, 03:33:56 PM »

thanks for the replies
I probably give it another try but for now it's playing with out sticking.
but now I see why those buttons always felt a little stiffer than the rest and while I'm in there I'll see if I can fix the squeak
in button 6 spring.
I wonder if a soldering tool could heat the rod enough to free it up?

The professionals will probably kill me for suggesting it, but have you thought of spraying if with a thin penetrating oil, like WD40 ?
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticky key
« Reply #9 on: October 20, 2013, 03:43:50 PM »

Don't send you boxes to pikey for repair.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #10 on: October 20, 2013, 03:59:09 PM »

 ;)

Does that mean wd40 is bad news ??  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: sticky key
« Reply #11 on: October 20, 2013, 03:59:47 PM »

Don't send you boxes to pikey for repair.
Don't send ANYTHING to Pikey for repair!  ;D
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #12 on: October 20, 2013, 04:04:04 PM »

I agree !!!!  :D

Seriously though Theo, is it acceptable to use any kind of lubricant on moving melodeon parts ? I've used sewing machine oil before. I know that dust tends to stick to it, but is there anything better.? What about the ptfe/Teflon sprays that you can get for lubricating cycle parts ? Or is it best not to use any lubricant at all?
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: sticky key
« Reply #13 on: October 20, 2013, 04:05:01 PM »

;)

Does that mean wd40 is bad news ??  ;)

No. World War Z is worse.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #14 on: October 20, 2013, 04:07:22 PM »

I heard that Tony Blair mistook WMD for OMD. Having that band in Iraq made him very worried......
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

IanD

  • Hero Member
  • *****
  • Online Online
  • Posts: 1703
  • Too many melodeons...
Re: sticky key
« Reply #15 on: October 20, 2013, 04:09:55 PM »

If keys are moving as you rotate the rod then either the hole in the wooden key is too small, or the rod surface has some roughness, or both.  When you get the rod out you can test for roughness by running your fingers along the rod and you will be able to feel any asperities.  These can be removed by gentle rubbing with very fine abrasive paper, I suggest 1200 grit.
When you've done this take each of the sticking keys and thread them onto the rod where they should swing freely.  If you do have to ream the hole be extremely cautious, it is very easy to remove too much wood and end up with a sloppy fit which will give the key a sloppy feel when playing. Sometimes it is sufficient to run the rod back and forth a few times through the hole. If that doesn't do it then a twist drill of the same size of the rod can be used IN THE FINGERS ONLY to team the hole. If you see the drill removing visible wood particles it is cutting too much. Take care.

My Oakwood has suffered exactly the same problem on several occasions (with years between them). As Theo said, the only thing that worked was to take the rod (and all the levers) out, clean the rod with a mild abrasive (green pan scrubbers work fine), and also run each key up and down the rod while rotating it to clear out anything in the pivot hole.

This has fixed the problem every time for me without risking using a reamer or a drill which can enlarge the holes.

Ian

P.S. If the levers aren't numbered (mine are!) write a number on the hidden heel of the lever, they need to go back in the same order they came off.

P.P.S. Don't do all the above in the back garden of a pub in Glasgow after 5 hours on the beer...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: sticky key
« Reply #16 on: October 20, 2013, 04:11:32 PM »

Seriously though folks, there are so many different lubricants out there is must be a mine field.
When you consider that our reeds are air dependant placing anything on them must surely create a problem. The trouble with sprays is that they get everywhere and can creep. I think the most benign substance could be Beeswax. What say you, you wonderful Fettlers all. ?
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

IanD

  • Hero Member
  • *****
  • Online Online
  • Posts: 1703
  • Too many melodeons...
Re: sticky key
« Reply #17 on: October 20, 2013, 04:23:13 PM »

Seriously though folks, there are so many different lubricants out there is must be a mine field.
When you consider that our reeds are air dependant placing anything on them must surely create a problem. The trouble with sprays is that they get everywhere and can creep. I think the most benign substance could be Beeswax. What say you, you wonderful Fettlers all. ?
A wood on metal pivot shouldn't need (or want!) any lubrication once the surface of the wood (inside the holes) becomes polished; IIRC the wheels in mills used to use hard wood teeth (hornbeam?) to mesh with cast iron cogs and lasted hundreds of years with no lubrication once both surfaces were smoothed and hardened.

Any lubricant with any kind of powder in (graphite?) might appear to free it up at first (think tiny ball bearings), but will then more than likely act as a grinding paste (since the particles aren't smooth) and wear the wood away over time.

Almost any liquid lubricant tends to go sticky as it ages and the more volatile components evaporate, especially with a lot of moving air around.

Wax will quite possibly increase the "stiction", and will probably pump out over time anyway.

I agree with Theo -- all lubricants are bad in this case :-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: sticky key
« Reply #18 on: October 20, 2013, 04:41:20 PM »

However, I was in a windmill once in Holland, in Leyden. And the Miller, never forgot his name ,Franz Croon or Frank Crown if you like. I was wearing a Barber waxed jacket at the time  and he invited us to come in and explore the windmill. Wax and flour don't mix. Anyway, at the top of the mill, the sails were whizzing round at a terrifying speed. I noticed some sheep fat hanging up (Lanolin). On questioning he said "ah yes, this mill is 300 hundred years old and we use Sheep fat to make the gears quieter and stop them wearing" all the cogs were wood and looked as good as they day they were made.
On emerging, someone said in an American voice " jeez, they got real Flour Graders in there"

So maybe Lanolin around the wooden bits?
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: sticky key
« Reply #19 on: October 20, 2013, 04:44:37 PM »

If you want to wrap a sheep around your wooden bits, I would keep it quiet if I were you.....  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal