Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: plastic bellows frame versus wood  (Read 2502 times)

0 Members and 1 Guest are viewing this topic.

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
plastic bellows frame versus wood
« on: November 18, 2013, 02:39:43 AM »

I have two nice used Hohner Erica's I recently bought. The one I like better leaks more air than the other at the bellows gasket. When I opened them up the one that leaks more air has a hard plastic bellows frame whereas the other one has a wooden one. I am thinking the plastic over time gives more and gets loose. Would it be a good idea to replace it with wood if that is even an option or is the plastic good and I should just put new gasket material on?  Thanks!!  :D
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: plastic bellows frame versus wood
« Reply #1 on: November 18, 2013, 05:58:04 AM »

Unless they're warped, plastic frames should be fine. Usually it's wood that warps. So first, have you identified the real source of the leaks? While a worn out gasket will certainly leak (and this is true for synthetic and natural materials), usually when an accordion is old enough to require a new gasket, it is also leaking in other places. The biggest ones I check are to make sure the bellows frames are not misshapen or warped. Then the bellows pins and I shore up the holes around the pins with magic wood. Also check where keyboard meets the carcass, and remove the reed block to check for a warped shoe where reed block meets soundboard. Then the padding of the pallets, and any stray holes or cracks with holes from screws and nails. If you want, run a bead of glue around the edge where the board meets the carcass. That ought to do it.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: plastic bellows frame versus wood
« Reply #2 on: November 18, 2013, 07:50:33 AM »

The leakage is more likely to come from where the bellows meets the plastic frames which are notoriously difficult to hold most types of glue.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: plastic bellows frame versus wood
« Reply #3 on: November 18, 2013, 07:56:05 AM »

I have seen quite a number of plastic bellows frames on Ericas, though I am not convinced any of them were original, but replacements, (though I could be wrong???).

I bought several sets of bellows with these frames from Hohner some years ago and was somewhat surprised that the holes for the bellows pins were pre-drilled, all slightly differently, and never quite aligned with existing holes in any body. Sensibly, I filled the holes in the frames and re-drilled them to match the body.

However, not every one would have done this if they had little or no repair experience. I have seen a number of these frames shattered by some one presumably having hammered the pins in, with no true guide holes even. These frames won't take that sort of punishment!!! (I doubt if wooden frames would either, but they are a bit easier to repair). Others I have seen have had the pins bent to try and reach the pre-drilled hole that are close, but not close enough to where they are required, or the pins being inserted at an angle and consequently distorting the holes in the body and allowing air to escape.

The other problem with these frames is that it seems the glue between the frame and the bellows always seems to fail; whether it is the glue or the frame material that is to blame, I don't know. (*See comment from Diatonix, cross-posted with this post.)

So I would suggest that you definitely isolate the leakage to either between the frame and the body or to the frame and the bellows. But there is a fair chance it could be both (like the one I spent the past weekend fixing!!! Grrrrrrr!!)

Sorry, this probably doesn't help you to fix the problem, but perhaps gives you a few clues as to the probable cause(s)....

Good luck.

*Edited to acknowledge cross posting.
and further edited to correct grammar...
« Last Edit: November 18, 2013, 08:45:10 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic bellows frame versus wood
« Reply #4 on: November 18, 2013, 09:18:57 AM »

Yes definitely isolate the exact source of the leak first.

But... my experience of plastic bellows frames on Hohners is that they are more likely to distort than are wooden ones, and the holes for the bellows pins seem to be more prone to wearing larger and even breaking out.   If I had to replace a set of bellows I would always prefer to use wooden frames, but I don't think I would go to the trouble of changing the frames if the bellows are ok.   Replace the gasket, check the pin holes, and check the glued joint between the frame and the bellows.

In the UK I see plastic bellows frames only on Hohners built in the last number of years before production moved to China.   I've only seen wood frames on Chinese built Hohners. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: plastic bellows frame versus wood
« Reply #5 on: November 18, 2013, 02:11:46 PM »

Thanks for all the feedback. I did locate a leak at the corner by the gasket so I am going to try putting thicker gasket material on first.  :||:
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: plastic bellows frame versus wood
« Reply #6 on: November 18, 2013, 02:32:39 PM »

Thicker gasket can put more pressure on the frame and cause it to twist more.   Best to use the same the original gasket thickness, which will of course be thicker than the old compressed gasket. 2mm may be sufficient, or 3mm might be needed, should not need any more than that.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: plastic bellows frame versus wood
« Reply #7 on: November 20, 2013, 11:15:34 PM »

I ordered 3mm, so I hope that will work. So, from your earlier post, my Hohner having a plastic frame means that it was probably made in Germany before they moved to China? That would be a plus for me I think. When did they move to China and how much is still done in Germany?
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: plastic bellows frame versus wood
« Reply #8 on: November 20, 2013, 11:57:13 PM »

A business group from Taiwan is the main shareholder (80% unless it's changed) in Hohner AG, the German company. This group has exclusive factories for Hohner goods made in China, and other factories that make other stuff unrelated. They bought the controlling interest in Hohner during the 1990s or early 2000s, when Hohner was floundering. I don't remember the year, for some reason 2002 is in my head, but it's in History Unfolds and elsewhere on the web. Probably someone else on the forum knows.

The Hohner "Made in Germany" line is still built in Trossingen. These are cuts above the Chinese products. Or in some cases, many cuts above.  (:) Quality control and materials for the Chinese accordions are often very poor.

Some general information that might answer questions:

- There are no Pokerworks, Ericas, Double-Rays, Compadres, Rey de Vallenato, Panther, Corsos, "standard" Coronas, or one-row stopper boxes built in Germany.
- Several variants of the Corona are built in Trossingen (Xtreme, Classic, etc.).
- Anacleto line are built in Italy, for Hohner.

hohner.eu has more complete infomation and I think an online tour.

FWIW I've used neoprene gasket tape (for marine or plumbing, etc.) for accordion bellows. It does the same job and is available at hardware stores but you may have to cut it to size depending on what the store offers.

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: plastic bellows frame versus wood
« Reply #9 on: November 21, 2013, 07:55:00 PM »

I replaced the gasket and there is still a small leak on one of the corners so I am suspecting it is between the frame and bellows. Would a bead of Elmer's glue be good for fixing? I was also thinking of maybe trying hot glue as the is flexible and stays bonded well. Any thoughts?

Thanks!!
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: plastic bellows frame versus wood
« Reply #10 on: November 21, 2013, 08:07:10 PM »

Any glue - unless you use a release agent on one face - will make it a lot harder to take apart next time. Have you got a really flat surface, e.g piece of flat glass, that you can lay the mounting faces on and see where the distortion is occurring?

And - is the leak small enough to ignore?
« Last Edit: November 21, 2013, 08:47:41 PM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: plastic bellows frame versus wood
« Reply #11 on: November 21, 2013, 08:45:22 PM »

Us Chansonistas aint afraid of a few leaks...... ::)
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: plastic bellows frame versus wood
« Reply #12 on: November 21, 2013, 08:48:18 PM »

Us Chansonistas aint afraid of a few leaks...... ::)

At our age you have to learn to live with them  >:E
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: plastic bellows frame versus wood
« Reply #13 on: November 21, 2013, 10:00:49 PM »

Well, I may be being a little compulsive about it   :-\  I am comparing the two Erica's I have and if you let the bellows fall without pressing any buttons the other one is a bit slower, so I guess I was trying to get the one I like to the same place. But, it may not be that big of a deal. How long should a bellows hold air if you hold it upright and just let it set without pressing buttons?
Logged

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Re: plastic bellows frame versus wood
« Reply #14 on: November 21, 2013, 10:04:48 PM »

Also, where I am thinking of gluing isn't between the accordion bellows and main frame, but the part that is inside the bellows where the bellows frame meets the bellows, so I wouldn't have to ever take that apart.  Thanks for all your input!!
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: plastic bellows frame versus wood
« Reply #15 on: November 24, 2013, 02:12:58 PM »

Us Chansonistas aint afraid of a few leaks...... ::)

At our age you have to learn to live with them  >:E

My name must not be coupled with this.  >:E
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal