Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Cut up long zinc plate to make individual reeds  (Read 1892 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Cut up long zinc plate to make individual reeds
« on: November 29, 2013, 05:26:15 PM »

I've got some Saxony boxes with one long zinc(?) plate per set of brass reeds, and I'm just tinkering with them to see how they can be revived... a kind of variation on Chansoneering. Seems to me there are so many of these old boxes out there it would be good to find a cheap way of reviving them.
Anyway, has anyone thought of or tried cutting up the long zinc plate to make individual reed plates? Is there any point in doing this, except ease of tuning and repair if you break a reed?
Also this would mean making reed blocks to match, which can't be all that difficult  :P, but I'll also need to mess about with the existing long reed block - like take it out.
So one problem (and there must be others that I haven't come across yet) is that after cutting you don't get an awful lot of plate before you get to the reed (because the reeds are quite close together on the plate), so fitting in a reed block would be delicate as there would be very little plate to overlap onto the block, and waxing might also be tricky.
And does anyone know what wood is best for reed blocks?

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Cut up long zinc plate to make individual reeds
« Reply #1 on: November 29, 2013, 05:52:07 PM »

And does anyone know what wood is best for reed blocks?

Most of the boxes I've dismembered have had reedblocks of well-seasoned slow-grown pine or of what looks like poplar. I usually use lime (aka linden) for repairs & replacements, partly because it's excellent for the job and partly because I have a fair amount of it.  I don't see why you shouldn't use any timber that's stable & not too dense; the mahogany family should fit the bill, as would holly, sycamore, alder etc.  The pine family can work well but ideally you'd go for instrument-grade slow-grown winter-felled spruce - Russian redwood from the DIY shop isn't going to be the best choice! Stay away from oily or resinous woods (they're the very devil to glue) and heavy-duty timbers such as oak, ash or elm, and avoid woods with wild or irregular grain because they're very hard to work to fine tolerances; otherwise the only real constraints are availability, weight and price.  Old solid wood furniture - especially drawers with mahogany sides - is an excellent cheap source of stable, well-seasoned timber. And I don't think I'd try MDF.... ;D

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Cut up long zinc plate to make individual reeds
« Reply #2 on: November 29, 2013, 05:53:37 PM »

especially drawers with mahogany sides

As I was posting this I thought of Nick's potential response... ::)
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Cut up long zinc plate to make individual reeds
« Reply #3 on: November 29, 2013, 05:57:12 PM »

I chucked away loads of laurel which I remember as being dense and close grained. Would be nicely seasoned by now...

Hadn't really though about MDF for reed blocks but I can't immediately think of its drawbacks, apart from maybe dust when machining.

PS
I had thought about modifying long reed plates, but couldn't see the gain. They are fairly easy to get the whole thing off, and I would have thought in-situ tuning would be about the same.
I've seen a couple of boxes I i liked and fancied fitting "normal" reed plates, but I think that would involve changing soundboard & pallet spacing etc so gets a bit major.
« Last Edit: November 29, 2013, 06:09:10 PM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Cut up long zinc plate to make individual reeds
« Reply #4 on: November 29, 2013, 06:05:50 PM »

Hadn't really though about MDF for reed blocks but I can't immediately think of its drawbacks, apart from maybe dust when machining.

Yes, nasty stuff to work. My concerns would be that it's very heavy for its volume, more vulnerable than timber to climatic conditions, and less forgiving to handling in and out of tight spaces than real wood. Be interesting to know if anyone's tried it, though.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Cut up long zinc plate to make individual reeds
« Reply #5 on: November 29, 2013, 06:21:10 PM »

Thinking over that last posting, I realised that MDF would at least be very stable, and it occurred to me that I have also seen reedblocks made from plywood. It would have to be good quality birch ply, I'd guess, but it would offer a good strength-to-mass ratio and should be extremely stable.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Cut up long zinc plate to make individual reeds
« Reply #6 on: November 29, 2013, 06:25:41 PM »

Thanks - great advice. And of course, old furniture is a great source of timber.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cut up long zinc plate to make individual reeds
« Reply #7 on: November 29, 2013, 07:34:09 PM »

Problem with renovating cheap Saxony boxes is that the reeds are often poor, broken reeds can be replaced by riveting in a new tongue. You could make new blocks but probably better to use decent reeds.  Then you have to do something about the poor treble action which is prone to break springs, loose buttons and leak air from the pallets.  The bellows are often poor quality too, finished with paper which tends to wear readily.  So by the time you have replaced the reeds, blocks, action and bellows you may as well build a new box.  But it can be quite satisfying if you can get thebox rebuilt to play well, and it is a good learning experience.

Of course if you find one of the less common models with reeds on separate plates and other parts also of a better standard then it's a different matter.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Cut up long zinc plate to make individual reeds
« Reply #8 on: November 29, 2013, 07:35:45 PM »

I have a friend who's a luthier, and he's very fond of Bubinga wood, for making guitar sides, and backs.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Cut up long zinc plate to make individual reeds
« Reply #9 on: November 29, 2013, 09:16:40 PM »

Problem with renovating cheap Saxony boxes is that the reeds are often poor, broken reeds can be replaced by riveting in a new tongue. You could make new blocks but probably better to use decent reeds.  Then you have to do something about the poor treble action which is prone to break springs, loose buttons and leak air from the pallets.  The bellows are often poor quality too, finished with paper which tends to wear readily.  So by the time you have replaced the reeds, blocks, action and bellows you may as well build a new box.  But it can be quite satisfying if you can get thebox rebuilt to play well, and it is a good learning experience.

Of course if you find one of the less common models with reeds on separate plates and other parts also of a better standard then it's a different matter.

Have to say I am coming to this conclusion myself. The best use so far is to make tuning bellows from the ..bellows, if they don't leak too much. There is v little to be done with the treble keyboard, as you say. There is no way to get them apart without destroying them; the only thing I can do is make a new one so might as well build a new box altogether.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Cut up long zinc plate to make individual reeds
« Reply #10 on: November 30, 2013, 12:41:01 PM »

I think Marcus Music uses waterproof MDF reed pans in his concertinas.

An Italian reed block maker told me that alder is best but any close grained wood will do. I often use cherry or maple.
Softwood is fine for waxed in reeds but hardwood is required if the reeds are screwed onto the blocks.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal