Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: reed problems  (Read 2369 times)

0 Members and 1 Guest are viewing this topic.

RobLandberger

  • Member
  • *
  • Offline Offline
  • Posts: 13
reed problems
« on: December 08, 2013, 02:20:34 PM »

Hi,

I have a second-hand Erica G/C, purchased a couple of months ago. Because the bass notes were a bit too deep into the case, and consequently playing it was becoming painful, I was trying to get a bit more purchase on them by bending them out a tiny bit.

In doing so, I've caused myself one or two problems, most of which I seem to have resolved, but I'm stuck with one: one of the reeds is sticking on the push; it releases itself on the pull, and then the push is ok again, but as soon as I leave it a starts playing up again and sounds very weedy. Any hints/suggestions, please? Or have I tried one "repair" too many this time?

Rob
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: reed problems
« Reply #1 on: December 08, 2013, 05:58:23 PM »

Bending the levers should not have any effect on the reeds so I think the problems are unrelated.
To fix the reed you will need to remove the bellows pins in order to access the reed block.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: reed problems
« Reply #2 on: December 08, 2013, 06:21:29 PM »

If the reeds were speaking properly before the changes, I suspect it's probably the lever or the button that's sticking, and leaving the pallet open by a tiny crack. If so, it's a case of tracing by trial and error where the friction spot is and deciding the best way of relieving it. Opening out the hole VERY slightly will probably do it if it's the button that's sticking, or gentle fine adjustment or light lubrication with something such as graphite if it's a pivot or a slightly rubbing lever.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

RobLandberger

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: reed problems
« Reply #3 on: December 11, 2013, 11:55:39 PM »

Thanks both. I seem to have sorted the situation out...reeds were sticking. Not quite sure what I did to unstick them...but it made me wonder how I go about lubricating the reeds?


Cheers again,

Rob
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed problems
« Reply #4 on: December 12, 2013, 08:09:32 AM »

it's a case of tracing by trial and error where the friction spot is and deciding the best way of relieving it.

Exactly!

Opening out the hole VERY slightly will probably do it if it's the button that's sticking,

That should ever be necessary, unless there is a visible defect in the wood eg the hole has not been machined to the full diameter, or the there is a splinter of wood causing a problem.   Opening out the hole will just jive you a button that feels sloppy and is more noisy.  Buttons sticking in holes are comparatively rare, and almost always caused by the button being misaligned.

but it made me wonder how I go about lubricating the reeds?

Presumably this was intended as a humorous remark?  There is nothing in a reed plate or block that can be improved by lubrication.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: reed problems
« Reply #5 on: December 12, 2013, 08:15:34 AM »

but it made me wonder how I go about lubricating the reeds?

Presumably this was intended as a humorous remark?  There is nothing in a reed plate or block that can be improved by lubrication.
From reading the previous posts, I think the OP is using the term 'reed' rather loosely, to include buttons and/or action. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: reed problems
« Reply #6 on: December 12, 2013, 09:58:49 AM »

but it made me wonder how I go about lubricating the reeds?

Presumably this was intended as a humorous remark?  There is nothing in a reed plate or block that can be improved by lubrication.
From reading the previous posts, I think the OP is using the term 'reed' rather loosely, to include buttons and/or action.

Yes, I think that too.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed problems
« Reply #7 on: December 12, 2013, 10:20:25 AM »

but it made me wonder how I go about lubricating the reeds?

Presumably this was intended as a humorous remark?  There is nothing in a reed plate or block that can be improved by lubrication.
From reading the previous posts, I think the OP is using the term 'reed' rather loosely, to include buttons and/or action.

Yes, I think that too.

I see what you mean, but it makes it harder to give good information if the questions are open to such wide interpretation.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

RobLandberger

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: reed problems
« Reply #8 on: December 13, 2013, 11:12:35 AM »

Just to set the record straight, it wasn't meant as a humorous remark.

I've been playing melodeon for a few years, and only recently have found myself delving into the inner workings of it, more out of necessity than desire, as I had to repair a broken spring. Once one starts delving, curiosity takes over and one wants to find out more. The question was asked purely out of ignorance - I  literally did not know whether it was possible to make the reeds "looser" - one or two were sticking, after all, and although I seem to have rectified the initial problem, I'm still not quite sure how I managed to do it!

I also know the difference between a reed, a button and actions, but I'd worked those out for myself.

I asked the question for guidance. "There is nothing in a reed plate or block that can be improved by lubrication " tells me all I needed to know. Now I know, thank you. However, I could have done without the rather high-handed reprimand for asking a question that wasn't sufficiently well structured. One has to start somewhere.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: reed problems
« Reply #9 on: December 13, 2013, 12:25:08 PM »

PM sent.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: reed problems
« Reply #10 on: December 13, 2013, 12:43:52 PM »

Ooh!  This is the conflict between the written and the spoken word. It is so easy to misread that that was written as opposed to a face to face conversation.  I'm sure there was absolutely no malice in the "reprimand"  probably just badly writ!
This forum is amazing for its discipline and good nature and long may it continue.
Shame about the Limericks though  >:E
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: reed problems
« Reply #11 on: December 13, 2013, 01:12:50 PM »

Nick's right - personally I didn't see any reprimand or high-handedness, just a couple of opinions based on the evidence as it stood at the time.  This forum is a very supportive and friendly one - if a reply was meant to be anything other than that, I imagine you'd be left in no doubt!

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: reed problems
« Reply #12 on: December 13, 2013, 02:19:01 PM »

Nick's right - personally I didn't see any reprimand or high-handedness, just a couple of opinions based on the evidence as it stood at the time.  This forum is a very supportive and friendly one - if a reply was meant to be anything other than that, I imagine you'd be left in no doubt!

Graham
Yep, have just pressed the LIKE button  ;D
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

RobLandberger

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: reed problems
« Reply #13 on: December 13, 2013, 06:36:10 PM »

Thanks guys,

I also agree that this is a very friendly and supportive site, and I've already gained hugely from my 5 hours spent on it! Perhaps it struck a nerve, as I hadn't intended to ask a question which was considered "open to such wide interpretation". I just didn't know. I do now, so I've gained knowledge from the posting, which is surely what it's all about.

 ;D



Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed problems
« Reply #14 on: December 13, 2013, 07:09:44 PM »

Rob, my "open to wide interpretation" comment was following on from what Steve suggested, not a direct response to your question.
Please do keep asking if you have more questions.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

RobLandberger

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: reed problems
« Reply #15 on: December 13, 2013, 10:53:32 PM »

Thanks, Theo.
Apologies for any misunderstanding/misinterpretation on my part. 
As I said, I've gained from the exchange, and folks sharing their expertise is what it's all about!
Thanks again.

Rob
 ;D
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal