Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Rusty bellows corners - replace or clean?  (Read 1963 times)

0 Members and 1 Guest are viewing this topic.

Dan

  • Member
  • *
  • Offline Offline
  • Posts: 12
Rusty bellows corners - replace or clean?
« on: December 11, 2013, 11:06:20 PM »

A request for advice here; needing to retape bellows on my Presswood, I thought I should also deal with the rusty corners. Searches haven't shown me much but this http://forum.melodeon.net/index.php/topic,526.msg4022.html#msg4022 does not encourage me to replace them.

So the questions are:

How bad a job is removing the corners?
How should I go about it if I do decide to do it?
Is cleaning, presumably with careful use of fine steel wool an alternative? (I'd worry about damaging bellows paper)
Does it really matter, other than visual appeal, is the rust at all likely to damage the bellows themselves?

All advice gratefully received.

Dan

 
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Rusty bellows corners - replace or clean?
« Reply #1 on: December 12, 2013, 12:20:13 PM »

I have no experience of actually doing a replacement, but my worry would be that the corners will deform a little as you pinch them up.  Apparently, the angle increases a little, but wait for advice from those who have done it.  The cleaning option is a bit of a temporary measure as the metal will corrode gaain quite quickly unless protected.  I'd suggest you cut up a Fairy Liquid botle to make a mask to protect the bellows paper whilst you're abrading the corners and then laquer the metal to protect them. 

At the end of the day, bellows are almost a consumable item and the real answer is to buy a new set!

Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rusty bellows corners - replace or clean?
« Reply #2 on: December 12, 2013, 12:29:01 PM »

Yes concur with the suggestion of new bellows.  The rust on the corners may well have had a damaging effect on the material under the metal, so if replacement bellows will blow the budget, then I suggest a little of time cleaning the worst rust off is about all that is worth doing.  Scotchbrite is a good material for removing rust.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Rusty bellows corners - replace or clean?
« Reply #3 on: December 12, 2013, 02:25:45 PM »

Rusty bellows corners and/or bellows pins in older Hohners are very often indicative of a more serious problem, namely rusty reeds.
Logged

Dan

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: Rusty bellows corners - replace or clean?
« Reply #4 on: December 14, 2013, 09:58:56 AM »

Thanks for replies, it doesn't seem worth putting that much work into the bellows although they still work fine as far as I can tell. I seem to have leaks from gasket which is what led me to think about overhauling bellows at the same time as replacing that.

I do have a set on a C box with cheap and nasty reeds which I'm fairly sure will fit. I need to check out how to fix bellows to frames; best glue, etc. See what I can find with a search.

Cheers

Dan

Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal