Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Melodeon tuning tools  (Read 13521 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Melodeon tuning tools
« Reply #20 on: January 05, 2014, 10:11:48 PM »

@Rees: I've just realized that I may have misunderstood your question. If you are referring to the scratchers made from worn-out quality files, the end is bent over after heating it, then shaped and finally hardened again..
Do you use "normal" heat treating/tempering methods (haven't thought about those for years!).

Cool in oil or water?

Thanks,
Malcolm

PS thought the video excellent.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon tuning tools
« Reply #21 on: January 05, 2014, 10:19:20 PM »

Your second assumption is correct. No need to worry about the ping. On the contrary: I'd get nervous if I didn't hear it (which may mean that I have chosen the wrong reed lifter and managed to bend the reed!).
I'm still surprised that these work without damage; if the reed end clearance is small (e.g. expensive hand-made reeds) the reed will have to be "shortened" by the difference between the lifter thickness and the clearance, which would mean quite a lot of lengthwise force on the reed which is "encastre" at the riveted base (look it up, like a beam rigidly mounted into a wall) so it can't even flex over the whole length.

Even if they do work in practice, as an engineer the idea gives me the willies... ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #22 on: January 05, 2014, 10:55:17 PM »

@diatonix, my reed lifters are completely flat and have no hook at the end!

@IanD your worst fears are realised, as the lifter goes through it pushes the reed tongue away from the slot. When it is pulled back the tongue clearance is so slight that the lifter is jammed between the tongue and the frame. Pulling causes the reed tongue to flex enough at the free end to ping along the lifter and flip through. I take your point about the stresses on the reed but the reason it took me so long to work out how to do this because I spent a long time pushing the lifter through at an upward angle then trying to force it down the back of the reed so that a greater length would flex, result? complete jam and bent reed lifter!

Accordion techs have used this method for decades without detriment to the reeds so I guess our natural instinct to recoil from it is unfounded. Sometimes brute force and ignorance knows best.  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Melodeon tuning tools
« Reply #23 on: January 05, 2014, 10:57:05 PM »

All I can say is that I cannot remember having ever done any damage to any of those small non-valved reeds. It all boils down to using the correct tool in the correct fashion. As I've pointed out earlier, a good "Rausheber" should do the job almost by itself... I admit that I sometimes abort the lifting of a reed and change to a different better suited hook. As soon as the hook catches the tip of the reed I can tell whether it's safe to lift it or not.
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #24 on: January 05, 2014, 11:07:31 PM »

I should also point out that I've never attempted to tune anything other than standard Hohner reeds. My Italian a mano reeded box will be sent to a good accordion tech for tuning as was my Liliput!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon tuning tools
« Reply #25 on: January 05, 2014, 11:16:49 PM »

@diatonix, my reed lifters are completely flat and have no hook at the end!

@IanD your worst fears are realised, as the lifter goes through it pushes the reed tongue away from the slot. When it is pulled back the tongue clearance is so slight that the lifter is jammed between the tongue and the frame. Pulling causes the reed tongue to flex enough at the free end to ping along the lifter and flip through. I take your point about the stresses on the reed but the reason it took me so long to work out how to do this because I spent a long time pushing the lifter through at an upward angle then trying to force it down the back of the reed so that a greater length would flex, result? complete jam and bent reed lifter!

Accordion techs have used this method for decades without detriment to the reeds so I guess our natural instinct to recoil from it is unfounded. Sometimes brute force and ignorance knows best.  ;D

<shudder>... :'(
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #26 on: January 05, 2014, 11:31:24 PM »

<shudder>... :'(

I'm intrigued. You're an engineer with a good grounding in theoretical physics (applied maths as we mortals know it) so how about undertaking a study of the forces involved in flipping reeds of different hardness of steel (Rockwell?) I am willing to donate several reed plates from a Scandalli accordion.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon tuning tools
« Reply #27 on: January 06, 2014, 09:21:58 PM »

<shudder>... :'(

I'm intrigued. You're an engineer with a good grounding in theoretical physics (applied maths as we mortals know it) so how about undertaking a study of the forces involved in flipping reeds of different hardness of steel (Rockwell?) I am willing to donate several reed plates from a Scandalli accordion.

I am indeed (also good grounding in structures and materials), and it's not the hardness as such that's the issue (Young's modulus is what matters), it's that to get the reed to bend to get past the lifter you need it to buckle like a thin column under compression, and the force needed to do this can be very high if the reed is almost straight at the time -- which it will be since it'll be almost parallel with the top of the reed frame -- and is probably higher the shorter the reed is, so treble reeds will be worse.

It's unlikely to break the reed since it *will* buckle and then bend, and they can bend a long way with no damage -- but if the initial force is big enough it could possibly loosen the rivets that hold the reed down, or move the reed down the frame if it's held down by a screwed clamp like a concertina reed or some bass reeds.

Even if it seems to work (or always works!) in practice, doing something like this to a hard steel reed that's supposed to only have a very small gap between it and the frame still makes me cringe -- it's doing something that's technically horrible just because you think can get away with it...

Which you could also say makes it good practical engineering, not physics -- reality trumps idealised theory every time :-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Melodeon tuning tools
« Reply #28 on: January 06, 2014, 09:32:47 PM »


It's unlikely to break the reed since it *will* buckle and then bend, and they can bend a long way with no damage -- but if the initial force is big enough it could possibly loosen the rivets that hold the reed down, or move the reed down the frame if it's held down by a screwed clamp like a concertina reed or some bass reeds.


Reeds typically are not completely straight, they usually have some degree of curve, I imagine that helps (??).

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon tuning tools
« Reply #29 on: January 06, 2014, 09:49:49 PM »


It's unlikely to break the reed since it *will* buckle and then bend, and they can bend a long way with no damage -- but if the initial force is big enough it could possibly loosen the rivets that hold the reed down, or move the reed down the frame if it's held down by a screwed clamp like a concertina reed or some bass reeds.


Reeds typically are not completely straight, they usually have some degree of curve, I imagine that helps (??).

It does, but as the lifter pulls it towards the frame this will straighten out. The force along the reed will depend very strongly on exactly how straight the reed is at the point where it bends, how thick the lifter is, how much reed clearance there is, how long (and thick) the reed is, the phase of the moon...

Either way, this method looks like an abomination that nevertheless works in practice ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Melodeon tuning tools
« Reply #30 on: January 06, 2014, 10:28:53 PM »

 I've noticed (or had the impression) that quite often reeds benefit from a good healthy "ping", sounding not only stronger than before, but also responding better. I wonder if other tuners have made the same observation?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Melodeon tuning tools
« Reply #31 on: January 06, 2014, 10:44:42 PM »

Yes I often find a good ping is necessary after filing a reed.  I always assumed this dislodged any loose filing debris.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #32 on: January 06, 2014, 10:48:18 PM »

I'll try and make a video of the tools I have actually being used, but that will be in the latter half of next week. In addition I'll measure the tools accurately if I can remember how to read a micrometer properly. (Theo can probably do that better than I can!)

Mr Dedic, is the phase of the moon crucial? Surely the ambient temperature would have more bearing. The higher the temperature the more pliable the steel but expansion would have an effect on the clearance gap and would the plate being made of aluminium or zinc (or even brass in the case of concertina reeds) have a significant effect on the outcome? All tongue in cheek of course but there's more than a small nod here to the imponderables that make simple answers impossible to many day to day questions.  8)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon tuning tools
« Reply #33 on: January 06, 2014, 11:05:07 PM »

I'll try and make a video of the tools I have actually being used, but that will be in the latter half of next week. In addition I'll measure the tools accurately if I can remember how to read a micrometer properly. (Theo can probably do that better than I can!)

Mr Dedic, is the phase of the moon crucial? Surely the ambient temperature would have more bearing. The higher the temperature the more pliable the steel but expansion would have an effect on the clearance gap and would the plate being made of aluminium or zinc (or even brass in the case of concertina reeds) have a significant effect on the outcome? All tongue in cheek of course but there's more than a small nod here to the imponderables that make simple answers impossible to many day to day questions.  8)

Indeed, which is why I said that if it works in practice that trumps any amount of theoretical analysis -- especially something with so many variables, including the ones you didn't think of. Simulation and calculations are only as good as your models and what you thought to simulate -- ask the designers of the wobbly bridge, which went wrong in a way nobody thought to check. It's been said that many structures are just looking to find a way of escaping from a load, and they'll often find a way out that nobody thought to check.

Still makes me wince, though... ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #34 on: January 06, 2014, 11:21:21 PM »

especially something with so many variables, including the ones you didn't think of.

They will have been legion!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Melodeon tuning tools
« Reply #35 on: January 07, 2014, 12:12:59 AM »

Yes I often find a good ping is necessary after filing a reed.  I always assumed this dislodged any loose filing debris.
Dave Elliott of Oughtibridge - he who wrote the 'Concertina Maintenance Manual' - explains that, when filing concertina reeds in the middle/root region to flatten the pitch, the removal of metal from the reed alters the stress distribution in the reed tongue, which in turn often causes the reed to curve down into the reed frame slot, preventing the reed from speaking. The remedy is a good upwards ping which seems to re-set the reed tongue to its proper position.

I've also found this to be the case with melodeon reeds; flattening a reed by using a file or broad-tipped scratcher over the width of the tongue tends to cause the reed tongue to bend down where all had been OK before. Again, a good upward ping is all that's needed to correct the reed height set (and it does indeed clear away fining debris. Flattening a reed by using a narrow tipped scratcher doesn't seem to have this undesirable effect.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Melodeon tuning tools
« Reply #36 on: January 15, 2014, 04:36:52 PM »

Had a spare 10 mins in the workshop today.

German Lifter Video

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Melodeon tuning tools
« Reply #37 on: January 15, 2014, 05:09:32 PM »

great vid. thank you.
makes for uncomfortable viewing initially, ...but gets easier the more times you watch it!
Logged

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Melodeon tuning tools
« Reply #38 on: January 15, 2014, 05:45:14 PM »


Mr Dedic, is the phase of the moon crucial?

Of course, plus the wearing of the ritual clothing, the burning of special incense, and the incantation before work starts

'nowwheredidiputmytoolsiamsureileftthemintheusualboxthedogmusthavemovedthem'.......
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Melodeon tuning tools
« Reply #39 on: January 15, 2014, 06:27:05 PM »

Had a spare 10 mins in the workshop today.

German Lifter Video

Just out of interest Lester have you tried pulling the reed through without using any leverage? The end of your reed lifter is even more mangled than mine!  :D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal