Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pallets on old Hohners  (Read 1419 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Pallets on old Hohners
« on: January 21, 2014, 10:33:25 AM »

I know this subject has been discussed but...
I have a couple of old Hohners: the pallets are a bit clacky but otherwise they don't leak and look in decent condition. The facing is a piece of chamois/soft leather, which is quite thin. I am aware that replacing the pallet facing means resetting the pallet on the end of the lever so that it sits exactly flat on the...er sound board (or whatever it's called). And if I upgrade the pallet facing to the felt/leather combo to quiet the pallet clack the lever will sit higher and the button(s) lower.
So what is the opinion on either (a) upgrading the facing and then adjusting the button position, or (b) leaving the thing as is, because it's not leaking and plays ok.
I mean from a restorer's perspective you always make this choice (you've been asked to do it by the owner? you factor the cost into the finished product?) Or do you always upgrade to improve the quality, by quieting the clack? Or are there circumstances where you leave the pallets alone?

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Pallets on old Hohners
« Reply #1 on: January 21, 2014, 10:45:15 AM »

I invariably fit felt/leather quieter facings and reset the button height. Whilst about it I also usually restrict the button travel.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pallets on old Hohners
« Reply #2 on: January 21, 2014, 11:16:30 AM »


I mean from a restorer's perspective you always make this choice (you've been asked to do it by the owner? you factor the cost into the finished product?) Or do you always upgrade to improve the quality, by quieting the clack? Or are there circumstances where you leave the pallets alone?

When renovating an old Hohner for sale re-facing pallets is a standard part of my overhaul procedure.  If working on a customers instrument I follow their instructions.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ted

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Pallets on old Hohners
« Reply #3 on: January 31, 2014, 12:46:38 PM »

On this subject, is there a minimum, or optimum, gap spacing between the pallet and soundboard with the key fully depressed? How is that gap determined? Is there any dependence on reed length or thickness, and subsequent amount of air, that may be required to sound the reed properly?
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Pallets on old Hohners
« Reply #4 on: February 01, 2014, 05:51:57 PM »

 I think you want about 1/8th of an inch clearance opening with the button depressed. This is more important on the low notes or distortion may occur on them if playing loudly.
 You want to watch out when adding thicker pads that you don't hit the underside of the grill with the button depressed.
If you remove the pallets and ad padding, clean out the slot on the pallet really well so the arm does not bind, ajust the arm so that it rests close to the middle of the pallet ,this can be aided by gluing a tiny 1mm thick dot of card in the middle of the slot, so the arm rests on it. Then glue ,or wax the arm in ,and finish with a cloth or leather dot glued over the arm and on the pallet.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal