Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Button travel on Hohner Cajun 114  (Read 5762 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Button travel on Hohner Cajun 114
« on: February 06, 2014, 03:24:19 PM »

A while ago there was a thread sharing the best ways to stop buttons disappearing into the keyboard on a Pokerwork, and a thread mentioning same on the Hohner one row 114 - (the Cajun lookalike), but no details were shared on solutions to this issue with the 114.
Please can you share your solutions to this?
I don't think a strip of wood within the plastic keyboard is going to help because you won't be able to get it on and off (you have to thread the key arms and buttons through the holes), but if I come up with something I'll share... honest.

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Button travel on Hohner Cajun 114
« Reply #1 on: February 06, 2014, 06:34:50 PM »

One of mine has a strip of brass  under the levers mounted with a bolt at each end from the top of the keyboard. . The depth can thus be adjusted by tweaking the bolts. There are no nuts, the strip is tapped  and springs around the bolt below the top stop it rattling.
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Button travel on Hohner Cajun 114
« Reply #2 on: February 06, 2014, 06:43:25 PM »

Ah I see. And it does the job ok?

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Button travel on Hohner Cajun 114
« Reply #3 on: February 06, 2014, 08:13:56 PM »

it could do with a strip of suede or felt adding  but it works well.
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Button travel on Hohner Cajun 114
« Reply #4 on: February 06, 2014, 09:25:37 PM »

Ive never had disappearing buttons on a 114, or a Pokerwork for that matter. I don't know why, all I can guess is that my fingers are more horizontal than vertical when I play.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Button travel on Hohner Cajun 114
« Reply #5 on: February 06, 2014, 10:29:15 PM »

A few months ago I cut off part of the tip of my RH ring finger. It's still quite sensitive and when the button drops into the fingerboard, the hole edge is quite sharp against this sensitive area, so I kinda want to solve the problem. Have to say I think the design of the pokerwork and 114 keyboard is crap in this respect. And Hohner do have a solution for this. I have an old Vienna box that has an access plate on the underside of the keyboard, lined with a key buffer; on the Modell 2 I have, the top of the keyboard comes off, so that the key lever assembly can be removed, revealing the key lever buffers. I'm wondering if I could cut out a plate from the keyboard casing with a Dremel saw, to duplicate this solution.
Oh.. The culinary mandoline is a lethal tool...

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Button travel on Hohner Cajun 114
« Reply #6 on: February 06, 2014, 10:36:20 PM »

Ouch :-( sorry to hear that Roger.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Button travel on Hohner Cajun 114
« Reply #7 on: February 06, 2014, 11:01:01 PM »

I once did the trick of a recessed backplate to a wooden hohner keyboard. Quite simple, with the right tools.

I made a plate from aluminium, traced the outline to the surface, and routet down 1 mm (thickness of the alu plate). Then routed through the whole wooden plate 5 mm further towards the center, leaving a 5 mm ledge for the alu plate. 4 small screws later, you have a removable back plate, ready for felt:)
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Button travel on Hohner Cajun 114
« Reply #8 on: February 06, 2014, 11:31:48 PM »

if you're stuck with a plastic fingerboard, limiting the travel can be more of a problem, a different set up to the two row. 
I've found that by just bevelling off the sharp edges of the holes with something like a small rotary dremel helps much more than you would think. it needs to be said, however, that a small round file would be much more in keeping with melodeon fettling ethos....but this is a plastic fingerboard!
I should add that the spring tension on this type of box usually needs reducing, which can reduce fingertip pressure.
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Button travel on Hohner Cajun 114
« Reply #9 on: February 06, 2014, 11:45:11 PM »

this advice re dremel and plastic...warrants a health and safety warning   ::)
Logged

tedrick

  • Guest
Re: Button travel on Hohner Cajun 114
« Reply #10 on: February 07, 2014, 01:11:08 AM »

I used a process of wedging strips of basswood craft wood under the hinge points of the levers and it really worked nicely -
I removed the keyboard fastened the strips along the surface of where the lever arms were the most near to the case - this served as a wedge to limit the travel near near the fulcrum point as opposed to ad the end of the arms - down under the buttons -

sorry this isn't very clear - I wish I would have taken pictures...
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Button travel on Hohner Cajun 114
« Reply #11 on: February 07, 2014, 01:20:42 AM »

I used a process of wedging strips of basswood craft wood under the hinge points of the levers and it really worked nicely -
I removed the keyboard fastened the strips along the surface of where the lever arms were the most near to the case - this served as a wedge to limit the travel near near the fulcrum point as opposed to ad the end of the arms - down under the buttons -

sorry this isn't very clear - I wish I would have taken pictures...

are these individual strips for each lever?
Logged

Harmonicatunes

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 261
    • Harmonicatunes
Re: Button travel on Hohner Cajun 114
« Reply #12 on: February 07, 2014, 01:49:12 AM »

I screwed a strip of wood horizontally inside the pallet cover. Works a treat. Only problem: now there is an extra clack
Logged
Harmonica Player
Just starting with the Box

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: Button travel on Hohner Cajun 114
« Reply #13 on: February 07, 2014, 02:21:52 AM »

are folks here talking about the traditional hohner one row, ha114, (2,3 or 4 stops, with two 'spoon' basses,) or maybe the American market Cajun model...or other?
I might be up the wrong tree? thanks.
Logged

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Button travel on Hohner Cajun 114
« Reply #14 on: February 07, 2014, 12:21:53 PM »

Keep kn mind that wood onder the levers will stop the levers very abruptly. I personally prefer felt under the buttons where possible, since it both stops softly, make no noise, and keeps the buttons in place when pressed down. I sometimes play hard, and if the button still 'wobbles' in the hole, it slows me down a little.

I've not worked on plastic keyboards, so things might be a little trickier for those.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Button travel on Hohner Cajun 114
« Reply #15 on: February 07, 2014, 05:43:34 PM »

are folks here talking about the traditional hohner one row, ha114, (2,3 or 4 stops, with two 'spoon' basses,) or maybe the American market Cajun model...or other?
I might be up the wrong tree? thanks.

I had in mind the HA114 for this problem. I don't know if the issue exists for the other ones you mentioned.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Button travel on Hohner Cajun 114
« Reply #16 on: February 07, 2014, 06:07:02 PM »

if you're stuck with a plastic fingerboard, limiting the travel can be more of a problem, a different set up to the two row. 
I've found that by just bevelling off the sharp edges of the holes with something like a small rotary dremel helps much more than you would think. it needs to be said, however, that a small round file would be much more in keeping with melodeon fettling ethos....but this is a plastic fingerboard!
I should add that the spring tension on this type of box usually needs reducing, which can reduce fingertip pressure.

You do have to be careful mentioning a dremel on this forum. :-X
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Button travel on Hohner Cajun 114
« Reply #17 on: February 07, 2014, 06:22:55 PM »

A while ago there was a thread sharing the best ways to stop buttons disappearing into the keyboard on a Pokerwork, and a thread mentioning same on the Hohner one row 114

The method I use on the pokerwork and Erica does not work on a 114 because the end if the instrument is different.  On the 2 rows the case extends up above the action board and gives a convenient surface yo mount the wooden strip that restricts the movement if the levers.  On a 114 the end of the instrument is almost flat except for a tiny ledge.  It might be possible to do something similar, but I've not tried.  It would certainly have to be fixed differently.

Pete Ward the maker of the Acorn replacement fingerboards is working on a design for a 114.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

ayreforcepyper

  • Member
  • *
  • Offline Offline
  • Posts: 20
Re: Button travel on Hohner Cajun 114
« Reply #18 on: February 17, 2014, 05:55:37 AM »

i put a strip of 1/4 inch (ish) craft foam under the buttons inside the plastic fingerboard. it works well, doesnt let the buttons drop into the fingerboard too much, and it doesnt stop the buttons abruptly. And it was cheap, and replaceable if the foam wears out. i used double sided tape to hold it in place.  the foam gives enough so that i was able to fit the fingerboard back onto the 114.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Button travel on Hohner Cajun 114
« Reply #19 on: February 17, 2014, 09:39:06 AM »

Yes I might try this, as a quick and easy solution. Craft foam can be bought (in the UK) from The Range, very cheaply, as can sheets of felt.
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal