Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Cutting a groove in a Double Ray finger board?  (Read 2383 times)

0 Members and 1 Guest are viewing this topic.

burnt nial

  • Member
  • *
  • Offline Offline
  • Posts: 37
Cutting a groove in a Double Ray finger board?
« on: March 05, 2014, 02:17:00 PM »

Anyone ever do this to a plastic finger board? I believe the material is thick enough at the edge to allow for a shallow groove. It wouldn't need to be very deep to serve it's purpose. The alternative of getting a new wooden board with all the fitting that would entail doesn't appeal to me at present. Thanks
nial
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Cutting a groove in a Double Ray finger board?
« Reply #1 on: March 05, 2014, 02:43:36 PM »

I use a router to groove a wooden finger board but I think that method would melt a plastic one and make a right mess.
Perhaps if you used a very shallow cut to take off a wafer thin slice at each pass but I still have my doubts.

Emery cloth wrapped around a dowel, perhaps. Long job though.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Cutting a groove in a Double Ray finger board?
« Reply #2 on: March 05, 2014, 02:46:39 PM »

I'm sure I've heard of shaping out a strip of wood, front and back, and sticking that onto the plastic fingerboard ?

I think it would be much easier and cheaper to buy one of Pete's wooden fingerboards. Dead easy to fit, and you know it will work.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Cutting a groove in a Double Ray finger board?
« Reply #3 on: March 05, 2014, 03:09:42 PM »

True dat.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Cutting a groove in a Double Ray finger board?
« Reply #4 on: March 05, 2014, 03:25:05 PM »

I too would go for one of Pete's wooden keyboards.

However if that is not an option for whatever reason I would avoid trying to groove a plastic keyboard.  There is no need to try to shape a bit of wood as   can be bought ready done from B & Q etc in 2metre lengths with one side flat and t'other grooved The slight lack of flatness on the edge of the plastic keyboard could easily be accommodated with the araldite used to glue the wood to the keyboard.

Having said all that  I think the simplest option is to get used to the non grooved keyboard!.  I prefer a groove but have absolutely no problem on boxes without the groove.

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Cutting a groove in a Double Ray finger board?
« Reply #5 on: March 05, 2014, 03:31:08 PM »

Yep, don't try to put a groove in the plastic. You could well end up with "it come apart in me ands Guv"
Syndrome  :'(
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Cutting a groove in a Double Ray finger board?
« Reply #6 on: March 05, 2014, 04:51:21 PM »

I switched from 'thumb behind' to 'thumb on edge' and have no trouble at all with Erica or Pokerwork fingerboard, and they have rounded edges.

The Dino Bafetti Black Pearl 3 is a different story though, the edge is very square and really cuts into your thumb.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Cutting a groove in a Double Ray finger board?
« Reply #7 on: March 05, 2014, 04:58:08 PM »

The slight lack of flatness on the edge of the plastic keyboard could easily be accommodated with the araldite used to glue the wood to the keyboard.

That would officially be a botched job, that would!

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Cutting a groove in a Double Ray finger board?
« Reply #8 on: March 06, 2014, 12:05:35 AM »

The gallant frigate Araldite stuck fast in Plymouth sound .............
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Cutting a groove in a Double Ray finger board?
« Reply #9 on: March 06, 2014, 12:33:41 AM »

Rees, I think you might have a virus, you are getting worse than Pikey and me. And that's saying something. 8)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

First pilot

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: Cutting a groove in a Double Ray finger board?
« Reply #10 on: March 06, 2014, 01:15:17 AM »

Plastic is only as thick as it needs to be for its purpose; so there is not enough there to make any kind of a cut or burn.  They should design in a thumb  slide in all accordian's so users have a choice.
Pilot
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Cutting a groove in a Double Ray finger board?
« Reply #11 on: March 06, 2014, 06:26:53 PM »

Here's an alternative for consideration. I have a DG Tommy that I love. My disappointment after receiving it was that the outer row of buttons was too close to the edge for comfort with my large hands. The Tommy has a concave finger groove but not in the right place for me. I wanted an extender that could be easily removed by a future owner if desired. I fashioned a piece of wood with another concave groove at a slightly different angle (see pictures) similar to some of the Hohner Club and Piccola boxes I have. I then hand filed and sanded the back edge to the approximate convex shape to match the existing keyboard groove.

The next task was to fit that convex shape exactly to the Tommy groove. By using a series of increasingly fine sandpapers with the back to the Tommy and the cutting side to the extension, I was able to get a perfect fit between the two. I did make a temporary fixture (no picture, but if you like I can locate and photograph it) that aided in keeping the top surface of the extension in the same plane as the top of the Tommy keyboard. I simply slid the extension back and forth along the edge. The convex surface slowly conformed to the Tommy's profile. It took less than an hour.

The final step was to place some good double sided tape to the convex interface surface and carefully connect the two. Because the fit is so close, it is attached very strongly without wobble. My guess is that it will stay for the duration of my ownership but is fully reversible by the next owner if I ever sell.

The Tommy remained completely unaltered.

Scott 
Logged
too many boxes...please buy one, or two, or

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Cutting a groove in a Double Ray finger board?
« Reply #12 on: March 06, 2014, 06:30:53 PM »

Excellent workmanship !
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Johnniez

  • Good talker
  • **
  • Offline Offline
  • Posts: 51
Re: Cutting a groove in a Double Ray finger board?
« Reply #13 on: June 17, 2015, 02:59:03 PM »

Yes indeed, very nice job..  Good on U !!!
Logged
Every Day Is A Great Day
Some Are Better Than Others
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal