Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Reed chamber depth variation  (Read 6666 times)

0 Members and 1 Guest are viewing this topic.

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Reed chamber depth variation
« Reply #20 on: June 05, 2014, 01:41:39 PM »

Very interesting. As always, it would depend on the sound that you want. I would expect this to reduce harshness, taking out some of the higher frequency content? But Franz' boxes are quite raw in their sound - perhaps due to some other design feature.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed chamber depth variation
« Reply #21 on: June 05, 2014, 02:01:46 PM »

Frans's Z strap crosses three sets of blocks, rotated 45 deg or so clockwise. The middle block screws to middle of the Z, others to its tips.

So in essence, two V joins, one looping to left, one to right, same piece of metal, simple. I'd expect it to act as an acoustic spring. With the weight judged right it'll transmit a wave very efficiently, but advance its phase by a fraction. That fraction would be frequency dependent.

All adding flexibility to the link (instead of it being rigid) does is to move the resonant frequency of the "bad" block slightly.

At the frequency where there is a block resonance (usually torsional along the length), to stop this you want to rigidly connect it to something which doesn't move. In practice this is the other reed block(s) which appears as a mass, assuming it's not resonating at the same frequency. Then when the second block has a resonance the first one doesn't and acts as a stabilising mass. What you end up with is two resonators coupled with a (relatively) stiff link.

If the link is flexible then it adds a bit to the torsional stiffness of the resonating block and just moves the resonance up a bit in frequency -- depending on where this is in the frequency range and how flexible the link is, it may or may not fix the problem or it may just move it to another note.

The whole system is much more complex than it first appears because there's no such thing as a rigid link -- just more or less flexible ones -- or a non-resonant mass (or a rigid case to attach everything to). Anything you do moves the resonant frequencies around, which could be from a bad place to a good one or vice versa. A simple analysis like Chris was trying to do is unlikely to be correct :-(

With any system like this, the real key to fixing resonance problems is usually to damp them, not just change the frequency and hope that it's better -- this is how problems like the Millennium Bridge get fixed. But it's difficult to see how you can build damped absorbers into the structure of a melodeon...

I'm not saying that reed block links don't work -- just don't try coming up with simple scientific-sounding explanations, because they're probably wrong ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Reed chamber depth variation
« Reply #22 on: June 05, 2014, 02:23:32 PM »

What it really needs is a fat strip of lead along the top edge of the block.
Plenty of mass and damping - but the box will be unliftable   >:E

It doesn't really matter too much - that strap is there to fix a problem evidenced by erratic burbling tremolo, but once the problem's fixed, adding more weight/stiffness won't improve things further.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Reed chamber depth variation
« Reply #23 on: June 05, 2014, 02:32:11 PM »

Never said it was simple. But you cannot ignore phase in any resonant system. In-phase can double things up, out of phase 180o completely cancel, even? In what I did (magnetic imaging) the phase is equally important to amplitude in things. Most kit codes X-axis on one, Y-axis on the other.

Been Googling: I'd mixed springs with coils (electrical equivalent). It looks that a phase retard happens. But one block retarded relative to other advanced .. comes to the same.  We discussed this last year:  "In the craft" these staps (all kinds) definitely have effects.  There is a certain lack eg test tones, oscilloscope stuff as to what?

Aha, Anahata's arrived. Won't heavier and heavier straps just end up with "no coupling" at the limit. It'd act as a wall? That's effectively what an air gap does.
Logged
  _       _    _      _ 

bellowpin

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 119
Re: Reed chamber depth variation
« Reply #24 on: June 05, 2014, 02:38:13 PM »

Frans's Z strap crosses three sets of blocks, rotated 45 deg or so clockwise. The middle block screws to middle of the Z, others to its tips.

So in essence, two V joins, one looping to left, one to right, same piece of metal, simple. I'd expect it to act as an acoustic spring. 
     
    the "Z" strap being angled at 45degree may have the additional effect of changing the direction of movement. the side to side rocking of the reedblock converted into a longetudinal motion .  however it works ,clever people will to continue to experiment and make improvements.   brian.
Logged
whole life in the shropshire hills. on the slow track and enjoying it.

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed chamber depth variation
« Reply #25 on: June 06, 2014, 01:51:48 PM »

Frans's Z strap crosses three sets of blocks, rotated 45 deg or so clockwise. The middle block screws to middle of the Z, others to its tips.

So in essence, two V joins, one looping to left, one to right, same piece of metal, simple. I'd expect it to act as an acoustic spring. 
     
    the "Z" strap being angled at 45degree may have the additional effect of changing the direction of movement. the side to side rocking of the reedblock converted into a longetudinal motion .  however it works ,clever people will to continue to experiment and make improvements.   brian.

I doubt that you'd get any significant longitudinal movement, a quick calculation suggests the longitudinal stiffness is at least 100x more than lateral...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Reed chamber depth variation
« Reply #26 on: June 06, 2014, 10:33:54 PM »

Enigmatic, Ian! As a Z strap has symmetry, how is that symmetry broken?
Logged
  _       _    _      _ 

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed chamber depth variation
« Reply #27 on: June 07, 2014, 01:12:25 AM »

Enigmatic, Ian! As a Z strap has symmetry, how is that symmetry broken?
I think that Ian is referring to the longitudinal stiffness of the reed blocks, not the Z-strap. Clearly the reed blocks are asymmetrical and very much less susceptible to end-to-end (longitudinal) movement compared with lateral side-to-side movement. It is the latter which a strap, Z or otherwise, is trying to prevent.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Reed chamber depth variation
« Reply #28 on: June 07, 2014, 02:10:43 PM »

Back to the original thread topic..... I recently ordered a set of C#/D reeds and blocks for my Swiss Erica.  The new blocks came with a tapered piece of wood down the center of the block effectively producing a gradual decrease in the reed chamber volume as you move toward the higher reeds.  The old G/C block did not have this.  The new block is on the right.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed chamber depth variation
« Reply #29 on: June 09, 2014, 01:32:46 PM »

Back to the original thread topic..... I recently ordered a set of C#/D reeds and blocks for my Swiss Erica.  The new blocks came with a tapered piece of wood down the center of the block effectively producing a gradual decrease in the reed chamber volume as you move toward the higher reeds.  The old G/C block did not have this.  The new block is on the right.
I don't know how long they carried on doing this because it must have been a pig to make, but the treble blocks in my Oakwood (first Model 4) are sort of spiral tapered to get smaller chambers towards the high reeds -- the width at the bottom of the block is constant but the width at the top tapers, so the angle of lean of the reed plates gradually increases with pitch.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal