Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Replacing Thumb strap Hohner Erica  (Read 5865 times)

0 Members and 1 Guest are viewing this topic.

shalomjj

  • Member
  • *
  • Offline Offline
  • Posts: 29
Replacing Thumb strap Hohner Erica
« on: May 26, 2014, 07:21:25 PM »

I have a Hohner Erica and I want to replace the thumb strap. I took off the finger board and lo and behold the thumbstrap is held in place with what looks like two permanent rivets.  :-[  Does anyone know how to change a thumbstrap in this situation?
Thanks!!
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing Thumb strap Hohner Erica
« Reply #1 on: May 27, 2014, 05:17:51 AM »

They are indeed rivets and the only way to remove them is carefully to drill them out.  I've removed a number of thumbstraps from Hohners but never replaced one as I can't be doing with them and losing the thumbstrap is the first job on any Hohner that comes my way, but the obvious way would be to replace the rivets with short machine screws and nuts.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Replacing Thumb strap Hohner Erica
« Reply #2 on: May 27, 2014, 10:04:22 AM »

Or just put in new rivets with a pop rivet gun, after drilling out the old ones. It worked for me until I ditched the thumb strap forever, and stopped getting blisters on my thumb !
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing Thumb strap Hohner Erica
« Reply #3 on: May 27, 2014, 11:56:45 AM »

Yes, I guess that would work!  I think I'd be a bit wary about using a pop rivetter on a fairly brittle plastic, but obviously it can stand up to it.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Replacing Thumb strap Hohner Erica
« Reply #4 on: May 27, 2014, 01:12:29 PM »

Yes, I guess that would work!  I think I'd be a bit wary about using a pop rivetter on a fairly brittle plastic, but obviously it can stand up to it.

It's also important to take care when drilling out the old rivets i.e. going through the dead-centres, not bearing down too hard (use a sharp drill bit) and providing adequate support behind.

From past shattering experience, pop-rivetting through the very brittle plastic requires careful selection of the right length rivets, as well as delicate control over the amount of riveter "squeeze" when nearing close of the rivet.

If I were doing this again, I'd use small stainless round-headed machine screws and Nyloc nuts as suggested by GPS. There's less possibility of damage, and if, like many of us, you decide the thumbstrap does nothing for you, you'll be able to take it off easily, and neatly fill the holes with black plastic caps.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Replacing Thumb strap Hohner Erica
« Reply #5 on: May 28, 2014, 02:00:41 AM »

They are indeed rivets and the only way to remove them is carefully to drill them out.

Not quite the only way! From experience, I have found that power tools and brittle, hard plastic don't mix too well. (I'm assuming the OP's Erica has a plastic keyboard, but the same probably applies to brittle old wood).

I remove the keyboard, then just cut the old strap off with a sharp blade (protecting the underside of the keyboard with a slim piece of brass). Once the leather is all cleared away, enough of the rivet remains proud of the keyboard to cut the head off with a pair of sharp cutters. Then just push the remains of the rivet through.  If the rivets are a tight fit though, a piece of wood the exact depth of the keyboard should be placed on either side of the rivets for support before pushing too hard....

Logged
Tuner/repairer, now retired.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Replacing Thumb strap Hohner Erica
« Reply #6 on: May 28, 2014, 06:19:55 AM »

They are indeed rivets and the only way to remove them is carefully to drill them out.

Not quite the only way! From experience, I have found that power tools and brittle, hard plastic don't mix too well. (I'm assuming the OP's Erica has a plastic keyboard, but the same probably applies to brittle old wood).

I remove the keyboard, then just cut the old strap off with a sharp blade (protecting the underside of the keyboard with a slim piece of brass). Once the leather is all cleared away, enough of the rivet remains proud of the keyboard to cut the head off with a pair of sharp cutters. Then just push the remains of the rivet through.  If the rivets are a tight fit though, a piece of wood the exact depth of the keyboard should be placed on either side of the rivets for support before pushing too hard....

You could use a hand drill........ ;)
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Replacing Thumb strap Hohner Erica
« Reply #7 on: May 28, 2014, 06:37:52 AM »

They are indeed rivets and the only way to remove them is carefully to drill them out.

Not quite the only way! From experience, I have found that power tools and brittle, hard plastic don't mix too well. (I'm assuming the OP's Erica has a plastic keyboard, but the same probably applies to brittle old wood).

I remove the keyboard, then just cut the old strap off with a sharp blade (protecting the underside of the keyboard with a slim piece of brass). Once the leather is all cleared away, enough of the rivet remains proud of the keyboard to cut the head off with a pair of sharp cutters. Then just push the remains of the rivet through.  If the rivets are a tight fit though, a piece of wood the exact depth of the keyboard should be placed on either side of the rivets for support before pushing too hard....

You could use a hand drill........ ;)

This is true! Somehow whenever a drill is mentioned I tend to think of my old clunky Dack and Blecker  :o

Still, I find I have more control with an edged tool than a pointy one.... Others may not!
Logged
Tuner/repairer, now retired.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Replacing Thumb strap Hohner Erica
« Reply #8 on: May 28, 2014, 01:43:22 PM »

A dremel cut off wheel works very well.  Much better than a drill. It very neatly will remove the top off of the rivet.

http://www.dremel.com/en-us/Accessories/Pages/SubCategories.aspx?catid=2058
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal