Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Best tool for removing bellows pins?  (Read 9469 times)

0 Members and 1 Guest are viewing this topic.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Best tool for removing bellows pins?
« on: May 28, 2014, 01:01:11 PM »

Dear All,
I need to remove the bellows pins to get into my Tommy's bass end to replace the reed block after it's been repaired.
An emergency fix on stage ( to see what was going on inside ) used a Gerber multi-tool pliers ( with one nose longer than the other! ) and at the time 'needs must'.
I think Theo uses a small pair of snipping pliers.

In my brain somewhere I'm sure there was a thread on what's best to use, and someone uses snipping pliers with a groove cut into both edges to enable the pin to sit in the groove without the cutting edges trying to cut through it. Seems a sensible modification.
I have countless pairs of ordinary pliers, though don't want to mark the pin or the casework by any gripping serrations in their jaws.
I think I'm popping into town tomorrow so could pick up some snipping pliers ( don't know their exact title ) if that's a good thing.
Any advice to those avid mechanic's out there?
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Best tool for removing bellows pins?
« Reply #1 on: May 28, 2014, 01:07:12 PM »

A cheap pair of small end-cutters. The cheap ones are usually not very sharp anyway, but it's simple enough to dull the edges to prevent damage to the pins. Some people do file a notch into the edges, but I've never found that necessary.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Best tool for removing bellows pins?
« Reply #2 on: May 28, 2014, 01:47:04 PM »

I keep meaning to attach a scrap of heavyish leather to the handles of my pincers to lay on the box to protect the finish should a bit of leverage be necessary - although to date I've always managed to get the pins out with a straight pull.  Usually I end up pulling the pins with a p[ocket tool - the purpose of which escapes me - in a pub garden, 'cause that's where and when the problem occured.  Then something to lever against rather than the casework is important.

Rob.
Logged

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #3 on: May 28, 2014, 01:53:24 PM »

end cutters that's what I meant!
Yep, taking the edge off them makes sense.
Thanks Graham, will investigate Maplins tomorrow.

Ahhh Rob's just replied.
Yes I can see something to protect the casework is a sound idea. To be fair, when I've seen them removed over the last couple of days, a steady straight pull looks like it will do.
If I'm right, end cutters are miniature pincers, so I suspect I'll find them easier to handle with care.
Thanks both
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Best tool for removing bellows pins?
« Reply #4 on: May 28, 2014, 02:25:53 PM »

You should avoid any tool that does not give the pin a straight pull.  Any levering that has a sideways component will tend to enlarge the holes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Best tool for removing bellows pins?
« Reply #5 on: May 28, 2014, 04:39:51 PM »

I use a very old pair of pincer/pliers. The kind that cobblers used to use, to pull out old nails, and rip off worn soles. It's also just about the right weight, for knocking them back in again.


John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Best tool for removing bellows pins?
« Reply #6 on: May 28, 2014, 06:15:00 PM »

I use a pair of end cutters to pull the bellows pin with a straight upward pull. I've never found it necessary to grind a cut-out slot in the middle of the cutter jaws.

To protect the casework of the instrument, I also use a small square scrap of chamois leather, with a slot and a hole which fits over the head of bellows pin head. I can grip the pin head with the end cutters through the hole in the chamois leather. See attached photo.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Foma

  • Member
  • *
  • Offline Offline
  • Posts: 21
    • Гармонь
Re: Best tool for removing bellows pins?
« Reply #7 on: May 28, 2014, 06:44:45 PM »

Accordion Pin Pliers


http://www.elane-electronics.com/musical_accessories/accordion_pliers.html

I made a similar pliers itself.
« Last Edit: May 28, 2014, 06:48:02 PM by Foma »
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Best tool for removing bellows pins?
« Reply #8 on: May 28, 2014, 06:58:34 PM »

You should avoid any tool that does not give the pin a straight pull.  Any levering that has a sideways component will tend to enlarge the holes.

This is an important suggestion. And, for instance, if you decide to attempt it with a pair of ordinary pliers and cover the pin with something to avoid marring it with the tool, use caution that the covering isn't so thick that you can't see if the pin is being tilted and enlarging the hole.

Nail clippers with a notch filed in them was a fun idea but offered me little grip. I did the same to a pair of blunted end nippers like the ones described above.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #9 on: May 28, 2014, 07:30:50 PM »

Thanks all, really sensible thoughts here.
Straight pull makes total sense, and I'm sure I have a little chamois leather to make Steve's protective patch.
I'll have a nose around tomorrow in town and see if I can come up with something as in Foma's picture.
Thanks for that, it gives me a visual prompt.
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Best tool for removing bellows pins?
« Reply #10 on: May 28, 2014, 07:45:51 PM »

I'll have a nose around tomorrow in town and see if I can come up with something as in Foma's picture.
Foma's picture is pretty much what my end cutters are like, except without the cut-out notch. I got mine from Homebase for about £3.50. As mentioned, I don't find the notch necessary - indeed it might almost be a disadvantage to have a cut-out notch: Hohner bellows pin heads are quite small and might well slip through a notch which was designed for fat-headed Italian pins.*

(* Have to be careful what I say there, to avoid any possible offence to the worthy inhabitants of that estimable nation!  ;) )
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Best tool for removing bellows pins?
« Reply #11 on: May 28, 2014, 07:52:37 PM »

Thanks all, really sensible thoughts here.
Straight pull makes total sense, and I'm sure I have a little chamois leather to make Steve's protective patch.
I'll have a nose around tomorrow in town and see if I can come up with something as in Foma's picture.
Thanks for that, it gives me a visual prompt.
Q

If you have a nearby Maplins
http://www.maplin.co.uk/p/rolson-mini-top-cutting-pliers-n23cy

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #12 on: May 28, 2014, 07:55:17 PM »

 ( shhh don't shout too loud )
Yep I've got a Homebase somewhere, plus B&Q and Maplins, so will have a good root around.
Cheers
Q

Ahhh someone else has replied - Lester - great! Maplins is my closest so will start there.
Thanks all.....
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Best tool for removing bellows pins?
« Reply #13 on: May 28, 2014, 08:38:23 PM »

I use a simple carpet tack lifter and keep it solely for removing bellows pins. I also have a dedicated piece of Whiskas cardboard for surface protection.   :-*
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #14 on: May 28, 2014, 08:44:34 PM »

Thanks Ebor fiddler..... only I use Iams for my cat  ;D
sorry couldn't resist. Yep take the point, a nice bit of cereal type cardboard will also do the trick.
Ta
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Best tool for removing bellows pins?
« Reply #15 on: May 28, 2014, 08:52:51 PM »

I use a simple carpet tack lifter and keep it solely for removing bellows pins. I also have a dedicated piece of Whiskas cardboard for surface protection.   :-*

No No No and once again NO!

The pins must be pulled out straight from the holes, using tack lifters etc puts sideways force on the pin and can cause the pins to enlarge the holes and cause air leaks and loose pins.

In case you didn't notice my previous NO!

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Best tool for removing bellows pins?
« Reply #16 on: May 28, 2014, 09:46:47 PM »

small joiners pincers (AKA end cutters) can be had from many £1 shops for £1!  As others have said  its a straight pull job with absolutely no waggling or levering.   Think of it being not unlike pulling teeth out  - the dentist doesn't lever  against your gum , other teeth or anything else .  Sometimes a 'tight' pull is easier with the box on the table and  you standing up rather than sitting down  as it is easier to get a straight pull that way.

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Best tool for removing bellows pins?
« Reply #17 on: May 28, 2014, 10:48:23 PM »

Come on gang, we are going round in circles.
 I have seen more bellows pins pulled up and down in the last few days than a Brides Nightie.
A decent pair of flat nosed pliers and a straight pull upwards does the trick, and I've  been watching experts!  :P
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Best tool for removing bellows pins?
« Reply #18 on: May 28, 2014, 11:18:55 PM »

I'll have a nose around tomorrow in town and see if I can come up with something as in Foma's picture.
Foma's picture is pretty much what my end cutters are like, except without the cut-out notch. I got mine from Homebase for about £3.50. As mentioned, I don't find the notch necessary - indeed it might almost be a disadvantage to have a cut-out notch: Hohner bellows pin heads are quite small and might well slip through a notch which was designed for fat-headed Italian pins.*

(* Have to be careful what I say there, to avoid any possible offence to the worthy inhabitants of that estimable nation!  ;) )

Absolutely true, the gap is a [mostly] needless feature and one gets along perfectly fine without it. In retrospect I realize that I added them to mine more for the enjoyment of 'specializing' a tool than real necessity. ;D

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Best tool for removing bellows pins?
« Reply #19 on: May 28, 2014, 11:20:06 PM »

Quote
the dentist doesn't lever  against your gum , other teeth or anything else

He does do some waggling, though. You needn't ask how I know...
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal