Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Best tool for removing bellows pins?  (Read 9489 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Best tool for removing bellows pins?
« Reply #20 on: May 28, 2014, 11:24:24 PM »

End nippers, as so many have already suggested and very much a straight pull. If the pins are really stubborn then sideways leverage is the last thing you should try! I have a tiny pair of 'Mole' or 'Vise' (American for vice) Grips, lock them onto the head of the pin at right angles and gently turn the pin in a circle to break the grip of rust and swollen wood before using the nippers to pull the pin straight out. That should do it!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Best tool for removing bellows pins?
« Reply #21 on: May 28, 2014, 11:36:28 PM »

small joiners pincers (AKA end cutters)
george

Sorry George but this is very misleading! End cutters/nippers are very sharp hardened cutters intended to cut metal almost flush to the surface, pincers are semi blunt end grips intended to drag nails out of wood. End nippers should either be blunted before gripping bellows pins or used with great care because they are sharp enough to bite the heads of the bellows pins off!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #22 on: May 29, 2014, 12:04:31 PM »

I agree with Anahata's description, I can confirm dentists do waggle  :(

Anyway I've just returned from town and popped into Maplins and ordered a pair of mini top cutting pliers. They didn't have a set there but have ordered direct from their warehouse 'delivery 3-5 days' which is fine.
Once I have them I'll run a file over the ends to blunt them.
I promise I'll use them with a straight pull  ;)
.... And will use either a thin piece of card or chamois leather cut to fit under the pin so's not to damage my casework.

Phew.... Think I'm sorted now. Thanks all for thoughts and advice
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Best tool for removing bellows pins?
« Reply #23 on: May 29, 2014, 01:01:51 PM »


Anyway I've just returned from town and popped into Maplins...
Q

I tell you what...you Devon lot know how to live... 8)
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Best tool for removing bellows pins?
« Reply #24 on: May 29, 2014, 01:48:12 PM »

End cutters/nippers are very sharp hardened cutters

That's why I suggested "cheap"; you can get a whole set of mini pliers including side-cutters, end-cutters, snipe-nose, curved and lord knows what for two or three quid in the market or at Aldi/Lidl etc. They're not desperately sharp to begin with, and not being made of the best Swedish tool steel are easy to blunt for use as pin-pullers.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Best tool for removing bellows pins?
« Reply #25 on: May 29, 2014, 02:25:59 PM »

That's why I moved to Brighton Baz, the frenetic excitement of Okehampton nearly did for me... ::)
Logged

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #26 on: May 29, 2014, 02:27:15 PM »

Baz: You would be surprised! Excitement - pah I spit at the word, it's all a total adrenalin rush here.

I realise the tool should be not of the best quality, hence Maplins @ £1.49, hopefully the cutting edge is made of best Swiss Cheese ( a mountain biking term for cheap bendy chainrings! )
Once I've filed the cutting edge off too that should do it.
As it's Castagnari, the pins are brass, and have been out twice in the last few days, so nothing more than a firm ( straight!! ) pull will be needed.
Q

Brian's added about Okehampton. Never go there.... just too much like Las Vegas ( apparently...)
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Best tool for removing bellows pins?
« Reply #27 on: May 29, 2014, 02:35:12 PM »

Swiss Cheese ( a mountain biking term for cheap bendy chainrings! )

Just replaced my cheese based tyres on my road bike with Gatorskins, rides better and hopefully less visits from the puncture fairy! 

Grumpy

  • Grumpy
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 134
Re: Best tool for removing bellows pins?
« Reply #28 on: May 29, 2014, 03:08:08 PM »

If you intend to remove pins on a regular basis try to get a pair of archery pliers, these are used to crimp small metal balls (just about the same size as bellows pins) onto a bow string. These pliers have a round cavity to take the ball and a lead through for the bow string there are no sharp or cutting edges, I do however use a small piece of low tack macking tape around the area of the pin to avoid accidents. Remember to pull the pin directly away from the instrument so as not to bend the pin or fracture the head from the spike. There are archery supplies in most areas or possibly EBay, mine came from Decathlon a sports store thoughout France they were only a few Euro.
Logged
Chris D, Surrey, UK
Getting old but still learning. Pokerwork G/D, Saltarelle L'Elfique G/D, Castagnari Lilly G/D and Hohner Liliput Declubed G/D + English concertinas, mandolins, recorders, tin whistles and other items unknown to household managment

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #29 on: May 29, 2014, 03:22:02 PM »

Lester - good tyres are a great investment, good luck with them. We get a lot of Puncture Piskies here, the Dartmoor equivalent, I understand your pain   ;)

Chris - thanks, sounds like a good idea, except have a set of end cut pliers on order now!
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

gurdypad3

  • Good talker
  • **
  • Offline Offline
  • Posts: 60
  • Gaillard D-G. Gaillard G-C.
Re: Best tool for removing bellows pins?
« Reply #30 on: May 29, 2014, 06:40:11 PM »

...a bit of common sense works best...to avoid dragging a thread out. ;)
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Putting the bellows pins back again
« Reply #31 on: May 29, 2014, 06:55:40 PM »

Just another bit of common sense and 'best practice'...

When you've removed the bellows pins, make sure that you replace them in the same hole from whence they came. Take care not to muddle them. Some people might think this is unnecessary, but in my experience, bellows pins from the same instrument can be of slightly differing diameters, especially the Italian ones. This can cause difficulties when trying to replace the pins, e.g. by trying to force a misplaced, fatter pin into a hole which is too narrow. Not good.  :(
 
To hold the pins whilst out of the instrument, I use a piece of expanded polystyrene (a base from pizza packaging is good) like a pin cushion; I've seen others use a block of wood with holes drilled in it as a rack to hold the pins safely.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #32 on: May 29, 2014, 07:58:57 PM »

Yes, I've seen mine being replaced by Theo and it was obvious that each were specific to their own hole.
Must remember!
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Best tool for removing bellows pins?
« Reply #33 on: May 29, 2014, 09:21:40 PM »

...a bit of common sense works best...to avoid dragging a thread out. ;)
Where can you get this from?
Do you need to use it if your pins are not threaded?
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Best tool for removing bellows pins?
« Reply #34 on: May 30, 2014, 04:31:13 PM »

I very often use a  Bosch mini chuck. Its 3 jaws (slightly modified by me) ensure a safe grip and perfect control, without any damage to the pin. A small piece of  leather with a hole for the pin head protects the casing, just in case.

http://i00.i.aliimg.com/wsphoto/v5/1381057872_1/mini-1-4-Inch-Keyless-font-b-Drill-b-font-Bit-font-b-Chuck-b-font.jpg_220x220.jpg
« Last Edit: May 30, 2014, 04:33:47 PM by diatonix »
Logged

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #35 on: June 01, 2014, 03:28:23 PM »

OK.... I started this thread knowing I will have to pull the pins on my bellows and replace the bass reed block after it's been re-waxed by Theo.
I ordered the end cutters as I'm in no rush, they will be delivered before the reed block is finished so all well and good.
I have my Hascy, my main weapon of choice to play so worries...........

After popping up to see the gang in Yeovil, I returned and played a tune or two, only to discover my Hascy has a sticky reed.
To coin a phrase " @rse!"
As you can tell by my sheer lack of knowledge shown on this thread, I've never opened up a melodeon before, which is bizarre as my English Concertina I could take apart and re assemble in the dark!
I also learnt from that what a reed sounds like when a bit of dust is stopping it sounding, a sort of strangled 'arghhhh' instead of a meaty full sound. The reed in question sounded just like that.
The Hascy has switches on the front, so I could tell by selecting a single reed, M, it was just a single reed high up on the D row, pushing, 2nd button in.
I had intended to wait until my tool arrived, but with a very busy week ahead dancing and hopefully playing in my monthly session,  it might be prudent to take time now and try and sort it rather than rush later in the week. In a drawer full of various pliers, cutters ( no! ) and pincers ( no again! ) I'd  found a nice small pair of pliers with smooth-ish inside gripping plates so I decided to give it a go.
I've drilled a piece of 2x1" wood with 8 holes and labelled hem in pencil top/bottom/ L, R etc to make sure the pins are kept for their specific hole, and a piece of card where I've cut a slot in to protect the casework.
I pulled the pins, ( straight pull, they were fine to remove ) put them in their labelled holes and gently lifted off the keyboard end - it's beautiful in there!
It is exactly as a picture I have from Steve Freereeder, and so I knew which reed I was heading for anyway. ( I'd also rang Steve quickly to discuss my first foray!)
I used a needle to gently ping the reed, and fitted the top half back on - reed sounds properly, job done!
I put the pins back and pressed them home with the end of my wooden block so's not to scratch, and after this will go and have a nice play..

To seasoned melodeon mechanics out there it seems a lot of fuss over nothing, but..... I've learnt it really is simple to get inside so long as you are careful and considerate to the pins and casework. I feel a congratulatory cup of tea coming on, plus some tunes......
A happy Q  (:)

Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Best tool for removing bellows pins?
« Reply #36 on: June 01, 2014, 05:03:42 PM »

Congratulations, my 12-sided friend!
Glad you've got that reed sorted, and pleased to have been of assistance along the way.
 (:)  :M  :|glug
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #37 on: June 01, 2014, 05:51:00 PM »

Yes, thank you so much for your guidance.
After chatting and consulting the photo I knew that once I'd got into it exactly which reed to head for.
I found I could ping it with a needle without having to take the reed blocks out which was a blessing, and a couple of pings was all it needed.
All good stuff!
cheers
Q  :|||:
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Best tool for removing bellows pins?
« Reply #38 on: June 01, 2014, 09:34:29 PM »

Knew you could do it Q . Why did you doubt yourself?  8)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Best tool for removing bellows pins?
« Reply #39 on: June 01, 2014, 10:04:50 PM »

Dunno really, p'raps I just needed a real reason to get inside!
Necessity being the mother of invention  and all that......
Also needed to practice for when my bass reeds return  (:)
Q
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal