Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: How to move reeds.. ? with a soldering iron ?!?!  (Read 2876 times)

0 Members and 1 Guest are viewing this topic.

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
How to move reeds.. ? with a soldering iron ?!?!
« on: September 13, 2014, 10:23:28 AM »

Hello all
I want to move several reeds on a new melodeon, as I've changed my mind about the keyboard.  I was going to send it to an expert for this job, but I've just read  Chris Ryall's  mail telling how he did it himself on his Handry.....with a soldering iron! 

I'd be glad of advice on how I might move reeds myself, without risking any damage.   Years ago I did succeed in flipping over the accidentals reeds for my Hascy, by slightly melting the wax and then quickly pulling off and pressing down the reeds.  They've stayed put for many years since, but I can't remember quite how I did it.

I'd be glad of some advice from melnetters. I don't want to take any risks!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #1 on: September 13, 2014, 11:09:32 AM »

If you want to make a premanent and good quality repair here is what I would do:

Remove the reeds and scrape off all the old wax and discard it.

Get some new wax, and a soldering iron with temperature control.   It is possible to use an uncontrolled soldering iron, but it is more difficult to make a neat job.     Place the reeds in the new positions and and use the new wax and iron to melt a bead of wax all round the reeds.  This takes a bit of practice but by the time you have done a few you will get the idea of keeping the wax where you want it.

Allow the wax to cool and then check the tuning of the reeds you have moved.   If its a wet tuned box any differences will probably be small enough to be un-noticed, with dry or swing tuning you might hear a difference.

Just re-melting the existing wax can work quite well, but can lead to reeds working loose after some time.   It just depends how permanent you want the changes to be.

Others may offer different advice of course, but these suggestions are based on experience.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #2 on: September 13, 2014, 11:21:50 AM »

Thank you Theo for such a prompt and comprehensive reply, and the authority of experience.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #3 on: September 13, 2014, 11:37:31 AM »

Wot Theo said or you could use silicone sealer  >:E

ps Don't use silicone sealer.
« Last Edit: September 13, 2014, 11:42:20 AM by Lester »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #4 on: September 13, 2014, 11:42:02 AM »

pps You don't say what box it is you are working one, if it is the likes of Castagnari Lilly or Hohner Liliput the task is harder as the reed plates butt against each other so replacing reeds other than the end ones can be a pain. You need to melt the wax on either side of the position where the reed goes and then quickly seat the reed in the still soft wax prior to rewaxing the top and the bottom of the reed plate.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #5 on: September 13, 2014, 12:13:30 PM »

I cut mine out with a scalpel, but then as above

And the time my 3 year old flicked the Lilly off my shoulder four plates came adrift spontaneously; those were waxed back in with a heated tent peg! As needs must …  :|glug
Logged
  _       _    _      _ 

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #6 on: September 13, 2014, 05:49:40 PM »

Do you know, Theo is a superb person not afraid to give all his skill away thereby reducing his trade.
Bravo Theo.
When I was on the Emmanual Pariselle course, there was no waxing, we used a type of double sided tape which seemed to work very well.
  To re- wax reeds is a real skill. I know I've tried it.
Go on have a go. I dare you. 8)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #7 on: September 13, 2014, 05:56:30 PM »

Do you know, Theo is a superb person not afraid to give all his skill away thereby reducing his trade.
Bravo Theo.
When I was on the Emmanual Pariselle course, there was no waxing, we used a type of double sided tape which seemed to work very well.
  To re- wax reeds is a real skill. I know I've tried it.
Go on have a go. I dare you. 8)

Unless Emmanuel has changed thinks I bet you were using Olivice which is cork 'tape' with adhesive on only one side. The reeds are clamped to the Olivice with the mounting screws.

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #8 on: September 13, 2014, 06:46:24 PM »

I use Charlie Marshalls method using a flat artists brush. It works for me  (:)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #9 on: September 13, 2014, 07:29:38 PM »

I use Charlie Marshalls method using a flat artists brush. It works for me  (:)

Different strokes for different folks, clearly.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #10 on: September 13, 2014, 08:34:48 PM »

Correct Lester.  (:)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #11 on: September 13, 2014, 10:16:16 PM »

If possible, leave this kind of job to an expert - especially if your box is new and valuable. I've seen way too many disastrous results!
« Last Edit: September 13, 2014, 10:18:05 PM by diatonix »
Logged

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #12 on: September 14, 2014, 10:27:22 AM »

Thanks for all the advice. It's great to know you are all out there ready to help!

Pat.

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 176
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #13 on: September 14, 2014, 11:17:39 AM »

If possible, leave this kind of job to an expert - especially if your box is new and valuable. I've seen way too many disastrous results!

            Sound advice , tried it myself once , and it was a complete disaster, lucky it was only 2 buttons on the base end.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #14 on: September 14, 2014, 11:34:40 AM »

Well, not so much a disaster as a lack of success - but it does render the box unplayable.  All the parts should be completely reusable after you've scraped all the wax off.  If it doesn't work, though you're in for a trip to your nearest or most favourite repairer and not at a time of your choosing.

Rob.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: How to move reeds.. ? with a soldering iron ?!?!
« Reply #15 on: September 14, 2014, 04:56:52 PM »

Melted wax seems to splash in tiny droplets very easily, and if you are careless little drops of wax can end up on the reed tongue or between the tongue and the reed slot, or in valves etc. I would suggest you try waxing in some old reeds first, just to get the technique right. I bought an old piano accordion for just this purpose.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal