Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Re facing pallets  (Read 12209 times)

0 Members and 1 Guest are viewing this topic.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re facing pallets
« on: September 27, 2014, 06:14:06 PM »

I have looked through and although there are plenty comments about refacing pallets, nowhere can I find hints/instructions on how to do it.
I have very clacky bass pallets on my Corona II, and would appreciate a hint or two, on how to go about refacing them, please.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #1 on: September 27, 2014, 07:29:59 PM »

Refacing pallets - here's how I do it...

1. Buy the correct stuff from Charlie Marshall. For a Corona II, I would recommend the Persian leather/felt composite. You will also need: PVA or Bostik clear contact adhesive, hot-melt glue and glue gun, sharp craft knife, medium sandpaper sheet, small Swiss-type flat file for cleaning up pallet slots/lever arms.

2. Remove the grille to access the pallets. They will probably be glued on to the lever arms with hide glue and a linen disk over the end of the arm, but possibly on a newer instrument with blob of hot-melt glue. With a pencil, mark a faint line on the pallet board-fondo thingy so you can eventually replace the pallets in the same position. Carefully remove the pallets by gently easing/rocking each one to-and-fro on the lever arm until the pallet comes away.

3. Carefully remove the old pallet facing by picking at it at one corner with a blunt blade; with luck the whole facing will come off more or less cleanly with a gentle pull. The wood base of the pallets can be quite thin and delicate, so take care not to be too rough and splinter off slivers of wood from the edge. If this happens, use PVA glue to stick the sliver back on.

4. Clean off any residual facing and glue by gently rubbing on medium to fine sandpaper on a flat surface such as a worktop or sheet of glass. Take care not to sand a convex surface onto the pallet.

5. Similarly, remove any residual glue from the slot where the pallet arm goes, and also clean off any old glue residue from the end of the lever arm.

6. Glue the new facing on to the cleaned-up pallets: lay the sheet of facing material felt side uppermost on a flat surface. Apply a thin coat of glue to the flat face of the pallet and press firmly into place on the felt. I use Bostik clear contact adhesive - just a single thin layer spread evenly on the pallet face and then pressed immediately on to the felt. You could also use PVA woodworking glue, but take care not to use too much so that it soaks through the felt and makes it stiff.

7. Glue and press all the pallets side-by-side on to the flat facing felt. Allow about a 2 mm gap between pallets. When all the pallets are pressed on to the sheet, cover the entire assembly with a sheet of scrap plywood or kitchen chopping board, etc. Place a few books on top to weight it down evenly and leave for a few hours for the glue to dry throughly.

8. Using a sharp blade on a cutting board, carefully cut round all the individual pallets from the facing sheet to leave a flush edge all round.

9. Reposition all the newly faced pallets on the pallet board with the lever arm spring tension holding them in place. Make sure the lever arm end fits snugly into the pallet slot. Carefully position the pallets so that they are all nicely lined up with the pencil line which you marked in step 2.

10. Using the hot-melt glue gun, fix each pallet on to the end of the lever arm with a small blob of glue. This takes a bit of care to manoeuvre the glue gun nozzle between the lever arms and to avoid messy strings of glue and oversize blobs. Practice on an old sheet of card first until you can control the glue gun properly. It also helps to have a thin sliver of card handy to catch the stringy bits of glue as you remove the glue gun from each pallet.

11. Adjustment: the pallets now will have a thicker facing than previously, so the buttons will be sitting slightly too far down in the keyboard holes. You now have to adjust each button height by very carefully and gently bending the lever arm away from the pallet board until the button height is correct (about 4 - 5 mm proud of the keyboard). This requires care and patience to get all the buttons at the same height. Also, you may find that some of the buttons are now not quite central in the keyboard hole and may be fouling on one side. Use a pair of thin round-nosed pliers to grasp the lever arm between the button and the keyboard hole edge and gently bend the lever arm slightly and gently to correctly centralise the button in the hole. Go gently, slowly and don't use excessive force.

That's it. You should end up with a quiet and even action, with airtight seals on the pallet board vents. Good luck!

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #2 on: September 27, 2014, 07:41:45 PM »

Addendum

When I wrote my previous post, I had in mind the replacement of the treble side pallets, but I've just noticed you were enquiring about the bass end pallets. The procedure is pretty much the same, except that you probably won't need any lateral adjustment on the bass buttons (step 11). You will need to adjust the button height though. 

In any case, I would recommend replacing both bass and treble end facings with the new felt/leather composite. It makes the entire action of the instrument so much quieter.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Re facing pallets
« Reply #3 on: September 27, 2014, 08:27:00 PM »

Thank you, nice, clear, and concise.

John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Re facing pallets
« Reply #4 on: January 10, 2016, 08:52:42 PM »

Refacing pallets - here's how I do it...

6. Glue the new facing on to the cleaned-up pallets: lay the sheet of facing material felt side uppermost on a flat surface. Apply a thin coat of glue to the flat face of the pallet and press firmly into place on the felt. I use Bostik clear contact adhesive - just a single thin layer spread evenly on the pallet face and then pressed immediately on to the felt. You could also use PVA woodworking glue, but take care not to use too much so that it soaks through the felt and makes it stiff.

10. Using the hot-melt glue gun, fix each pallet on to the end of the lever arm with a small blob of glue. This takes a bit of care to manoeuvre the glue gun nozzle between the lever arms and to avoid messy strings of glue and oversize blobs. Practice on an old sheet of card first until you can control the glue gun properly. It also helps to have a thin sliver of card handy to catch the stringy bits of glue as you remove the glue gun from each pallet.
Steve, it looks like I should expect the pallet facing and pallet mounting to separate nicely from your description. If I use PVA glue and hot glue gun to replace them, am I going to cause more trouble later if I need to undo my fix? I've got a table tennis rubber glue, that means I can just unpeel the rubbers from my bats and reglue them to other bats, wouldn't something like this be better than PVA? And does the hot glue also release well if I need to undo a poorly fitted pallet later on?
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #5 on: January 10, 2016, 10:23:09 PM »

Refacing pallets - here's how I do it...

6. Glue the new facing on to the cleaned-up pallets: lay the sheet of facing material felt side uppermost on a flat surface. Apply a thin coat of glue to the flat face of the pallet and press firmly into place on the felt. I use Bostik clear contact adhesive - just a single thin layer spread evenly on the pallet face and then pressed immediately on to the felt. You could also use PVA woodworking glue, but take care not to use too much so that it soaks through the felt and makes it stiff.

10. Using the hot-melt glue gun, fix each pallet on to the end of the lever arm with a small blob of glue. This takes a bit of care to manoeuvre the glue gun nozzle between the lever arms and to avoid messy strings of glue and oversize blobs. Practice on an old sheet of card first until you can control the glue gun properly. It also helps to have a thin sliver of card handy to catch the stringy bits of glue as you remove the glue gun from each pallet.
Steve, it looks like I should expect the pallet facing and pallet mounting to separate nicely from your description. If I use PVA glue and hot glue gun to replace them, am I going to cause more trouble later if I need to undo my fix? I've got a table tennis rubber glue, that means I can just unpeel the rubbers from my bats and reglue them to other bats, wouldn't something like this be better than PVA? And does the hot glue also release well if I need to undo a poorly fitted pallet later on?

That's why I prefer to use contact adhesive for fixing the facing to the pallets. It doesn't set totally hard like PVA does, so it is easier to clean off at some point in the future, should it become necessary. I don't know about table tennis bat rubber glue; it sounds a bit like Copydex latex glue which is horrible stuff and I wouldn't recommend it at all.

Hot melt glue remains flexible and can be peeled off and cleaned up fairly easily if ever needed.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Re facing pallets
« Reply #6 on: January 10, 2016, 11:56:17 PM »

Thanks, Steve. It is a little bit like Copydex, but less lumpy. Peels off a treat.
Should explain the rubber bit is the hitting surface that you glue on to the plywood (if you can call anything that pricey plywood). The 'rubber' doesn't mean rubbery glue. Modern table tennis glues are human friendly - VOC free, and seriously easy to use. Not cheap, but I've got plenty lying around.
« Last Edit: January 12, 2016, 12:03:31 AM by playandteach »
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

AlexCJones

  • Good talker
  • **
  • Offline Offline
  • Posts: 89
  • 3 row Hohner GCF 16 Bass
Re: Re facing pallets
« Reply #7 on: January 16, 2016, 03:58:10 AM »

Thanks.  I needed this post.  There is another one in which East Clare Box Player tells how he glues sheets of 1/16" wool felt to chamois leather.  At the moment, I find that preferable to having to order from across the ocean.
 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Re facing pallets
« Reply #8 on: January 16, 2016, 09:00:41 AM »

Chamois leather is not ideal, it can be rather variable in thickness.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Re facing pallets
« Reply #9 on: January 16, 2016, 10:53:51 AM »

Just refaced the pallets on the Hohner Erika I got from German ebay. Very satisfying. Had good advice over the phone from Charlie Marshall and went with bog standard bostik glue, to wood surface only. The felted leather he supplied is gorgeous.
Now have to fit, reset key height (by the way I cleaned up the buttons with an electric toothbrush). I'm going to use a hot glue gun on hot setting, unless anyone screams at me, for gluing arms to pallets after getting key height sorted.
SO therapeutic. Hope it all ends up working.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #10 on: January 16, 2016, 02:53:27 PM »

Just refaced the pallets on the Hohner Erika I got from German ebay. Very satisfying. Had good advice over the phone from Charlie Marshall and went with bog standard bostik glue, to wood surface only. The felted leather he supplied is gorgeous.
Now have to fit, reset key height (by the way I cleaned up the buttons with an electric toothbrush). I'm going to use a hot glue gun on hot setting, unless anyone screams at me, for gluing arms to pallets after getting key height sorted.
SO therapeutic. Hope it all ends up working.

You are doing all the right things with the right materials. You should end up very satisfied.  (:)

The felt/persian leather composite from Charlie Marshall is indeed very fine. I fail to understand why others persist in trying to cobble together anything else when the very best materials are so readily available from this most trustworthy and reliable source.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Re facing pallets
« Reply #11 on: January 16, 2016, 05:16:07 PM »

I assume that standard bostik glue is what we in the US would call contact cement?  It seems bostik makes many adhesives.
Logged

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Re facing pallets
« Reply #12 on: January 16, 2016, 05:20:45 PM »

I assume that standard bostik glue is what we in the US would call contact cement?  It seems bostik makes many adhesives.
Just says Bostik All purpose clear glue on the tube. It was easy enough to apply, and no sign of pulling away as I trimmed the facing after gluing. Also dirt cheap.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Re facing pallets
« Reply #13 on: January 16, 2016, 06:00:51 PM »

Not the contact cement I know then.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Re facing pallets
« Reply #14 on: January 16, 2016, 08:28:37 PM »

I used regular wood glue when doing wood pallets to felt, applied to wood only then pressed to felt.
You then have time to adjust if needed.
Contact cement you apply to both surfaces let dry to the touch, and no adjustments once the two surfaces meet.  hence the name
Sounds like you used the glue that he sells for valves also, which I'm sure is fine. Maybe a little harder to work with as it is quite stringy, well the stuff I used was.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Re facing pallets
« Reply #15 on: January 16, 2016, 08:30:57 PM »


The felt/persian leather composite from Charlie Marshall is indeed very fine. I fail to understand why others persist in trying to cobble together anything else when the very best materials are so readily available from this most trustworthy and reliable source.

Probably because Alex-C-Jones despite his very British sounding name is on the other side of the planet , Charlie can send the stuff overnight to us here (Miraculously fast in a lot of cases) but I can understand a reluctance to order to the USA (Time, Distance, cost, diminishing returns etc) ..

I use EVOstik for valves
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #16 on: January 16, 2016, 10:53:32 PM »


The felt/persian leather composite from Charlie Marshall is indeed very fine. I fail to understand why others persist in trying to cobble together anything else when the very best materials are so readily available from this most trustworthy and reliable source.

Probably because Alex-C-Jones despite his very British sounding name is on the other side of the planet , Charlie can send the stuff overnight to us here (Miraculously fast in a lot of cases) but I can understand a reluctance to order to the USA (Time, Distance, cost, diminishing returns etc) ..

I use EVOstik for valves
Charlie sends stuff abroad including USA. No problem. Just send him an e-mail.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Re facing pallets
« Reply #17 on: January 16, 2016, 11:23:23 PM »

Contact cement you apply to both surfaces let dry to the touch, and no adjustments once the two surfaces meet.  hence the name
That may be what it tells you on the package instructions.
However, it is perfectly possible to use contact adhesive on a one-surface application and join the two parts immediately. There is a short adjustment time possible. This is a good method for attaching pallet facing to pallets as several of us on here, and also Charlie Marshall who sells the blimmin facing material, keep recommending.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Re facing pallets
« Reply #18 on: January 17, 2016, 12:01:02 AM »

Refacing pallets - here's how I do it...
Now I've done this, I realise that the advice given is sound. Any mistakes made were due to lack of experience, but this really is a step by step idiot's guide. Button height and lateral adjustment is tricky - but it is more the front / back adjustment that is fooling me - you'd need to be able to bend against the intentional strength of the lever. I'm guessing that either I've set the buttons too high, or the celluloid finger plate has shrunk - or both.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Re facing pallets
« Reply #19 on: January 17, 2016, 12:20:28 AM »

Actually I remember when the instructions on glue tubes gave details for use as a contact adhesive and for single surface application - though the price paid for a little adjustment time was an extended drying time.  Of course, with felt onto a pallet one wouldn't dream of trying to peel it off and restick it.

Rob.
Logged
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal